• Description for Loxeal 31- 10

    Loxeal 31- 10 is a 2-Part 2-Part Cure Epoxy resin Liquid used to Adhere Rigid PVC, ABS and Polyester

    *See Terms of Use Below

    Chemical Resistance Chemical Resistance: Fluid Resistance: Well resistant to water, Well resistant to gasoline, Chemical resistance
    Application Type Bond
    1 Part or 2 Part 2-Part
    Material Form Liquid
    Substrate Rigid PVC, ABS, Polyester, Some plastics, Wood, Concrete, Glass, Ferrite, Metals, Marble, Steel, Ceramic
    Manufacturer Loxeal
    Cure Method 2-Part Cure, Room temperature
    Application Temperature (°F) <59
    Gap Fill (in) 0.004 to 0.079
    Cure Temperature (°C) 25
    Cure Time (min) 720 to 1,440
    Color Transparent, Amber, After mixing
    Oil Resistance Well resistant to oils
    High Temperature Resistance (°C) 80
    Low Temperature Resistance (°C) -40
  • Technical Data for Loxeal 31- 10

    • Chemical Resistance
      • Chemical Resistance : Fluid Resistance : Water Resistance - Well resistant to water
      • Chemical Resistance - Well resistant to gasoline
    • Application Type
    • 1 Part or 2 Part
      • 2-Part
    • Material Form
      • Liquid
    • Substrate
    • Industry
      • Other - Structural adhesive, Multipurpose
    • Cure Method
      • Room Temperature / Air Dry - Room temperature
      • 2-Part Cure
    • Color
      • Amber - Amber, After mixing
      • Clear / Transparent - Transparent
    Cure Specs
    Application Temperature (°F) <59
    Gap Fill (in) 0.004 to 0.079
    Cure Temperature (°C) 25 Test Method
    Cure Time (min) 720 to 1,440 Test Method
    Work / Pot Time (min) 90 to 150 Test Method
    Mix Ratio 1:1 (by volume)
    Bond Strength
    Peel Strength (piw) 10 - 25 (N/25mm) Test Method
    Shear Strength (psi) Test Method
    Material Resistance
    Oil Resistance Well resistant to oils
    Environmental Resistance Environmental resistance
    High Temperature Resistance (°C) 80
    Low Temperature Resistance (°C) -40
    Business Information
    Shelf Life Details 1 year in original unopened packaging at +5°/+25°C
    Shelf Life Temperature (°F) 41 to 77
    Shelf Life (mon) 12
    Not Good For
    Don't Use With Rubber, Soft materials, Polyethylene, Polypropylene, PTFE
  • Best Practices for Loxeal 31- 10

    *See Terms of Use Below

    1. Surface Preparation

      For best results we recommend to scratch the surfaces with a tool and then to degrease and clean with Loxeal Cleaner 10 or Acetone and let dry for a few seconds.

    2. Application

      Apply product at temperature higher than +15°C.

      Assembly: Parts to be bonded shall be assembled immediately after product application and kept close until full polymerization without providing any mechanical stress.

    3. Mixing

      The resin and the hardener need to be mechanically mixed before use in the ratio of weight and/or volume in compliance with technical specifications until a homogeneous colour is reached. Products are available in dual cartridges with proper static mixers (separately provided) allowing a direct and correct product application on the substrates to bond, completely discarding the first 3/5 cm of the extruded product. Avoid excess of product blend because heating produced by chemical reaction may cause risk and loss of product.

    4. Clean-Up

      Excess of product can be removed with Acetone or any other solvent based cleaner compatible with the substrates to bond. Application tools and dosing systems shall be cleaned before the product is hardened.

    5. Removal

      Cured product can be removed only mechanically.

  • Comparable Materials for Loxeal 31- 10

    *See Terms of Use Below

    Spec Engine® Results

    Closest Results from this Manufacturer

Popular Articles

6 objects held together by adhesives you probably can't live without

Read Article

Testing the effectiveness of surface treatments

Read Article

Lightweighting drives automotive adhesives demand

Read Article

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Read Article

Sponsored Articles

Unique Advantages of Contact Adhesives

Read Article

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Read Article

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Read Article

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Read Article

Featured Ads

Gluespec Poll

When you're researching or sourcing materials online, what device are you using?
Work / Pot Time Test Methods
Work / Pot Time Test Method Temperature
90 to 150 min Usable/Pot life, Curing, Time detected using 2 g of Part A +Part B mix 25°C
Cure Time Test Methods
Cure Time Test Method
720 to 1,440 min Functional cure time
Cure Temperature Test Methods
Cure Temperature Cure Time Test Method
25°C Functional cure time
Shear Strength Test Methods
Shear Strength Cure Temperature Substrate Test Method
Peel Strength Test Methods
Peel Strength Cure Temperature Test Method
10 - 25 (N/25mm) 25°C ISO 4578, Curing