3M (08155) Quick Fix Adhesive Datasheet 3M (08155) Quick Fix Adhesive

CONTACT REP
Information provided by Gluespec

  • Description for 3M (08155) Quick Fix Adhesive

    Fast Rate of Strength Buildup. Good Adhesion to EPDM Rubber, Plasticized Vinyl and Most Plastics. Good Resistance to Alcohol, Soap Solutions and Cleaning Agents

    *See Terms of Use Below

    Chemical Resistance Alcohol, Soap Solutions, Cleaning Agents
    Application Type Bond, Adhesive: Instant Adhesives
    1 Part or 2 Part 1-Part
    Material Form Liquid, Thin Fluid
    Substrate Plasticized Vinyl, Most Plastics, EPDM Rubber, Rubber (including weatherstripping), Metal (painted or bare), Glass
    Manufacturer 3M
    Chemistry Cyanoacrylate, Solvent-free
    Cure Method Moisture
    Cure Time (min) 720
    Viscosity (cPs) Thin fluid, 400 to 600
    Color Transparent, Colorless
    High Temperature Resistance (°C) 71
    Other Resistance Run off
    Density (g/cm³) 8.7 to 9.0 (lbs/Gallon)

  • Technical Data for 3M (08155) Quick Fix Adhesive

    *See Terms of Use Below

    Overview
    • Chemical Resistance
      • Chemical Resistance - Alcohol, Soap Solutions, Cleaning Agents
    • Application Type
    • 1 Part or 2 Part
      • 1-Part
    • Material Form
      • Liquid
      • Other - Thin Fluid
    • Substrate
      • Glass
      • Metal - Metal (painted or bare)
      • Plastic - Most Plastics
      • Vinyl - Plasticized Vinyl
      • Rubber - Rubber (including weatherstripping)
      • EPM/EPDM - EPDM Rubber
      • Other - Variety of substrates, Trim pieces, Emblems, Side moldings
    • Industry
      • Other - close fitting parts
    • Chemistry
    • Cure Method
      • Moisture / Condensation Cure - Moisture
    • Color
      • Clear / Transparent - Transparent, Colorless
    Specifications
    Cure Specs
    Cure Time (min) 720
    Viscosity (cPs) Thin fluid, 400 to 600 Test Method
    Set Time (min) Quick
    Bond Strength
    General Bond Strength (psi) Good
    Material Resistance
    High Temperature Resistance (°C) 71 Test Method
    Other Resistance Run off
    Other Properties
    Flash Point (°F) 176.0 Test Method
    % Solids (%) 100 Test Method
    Density (g/cm³) 8.7 to 9.0 (lbs/Gallon) Test Method
    Business Information
    Shelf Life Details Store at room temperature. Rotate stock on a "first-in-first-out" basis. When stored at the recommended conditions in original, unopened containers, this product has a shelf life of 12 months.
    Shelf Life Temperature (°F) 77
    Shelf Life (mon) 12
    Not Good For
    Don't Use For gap filler

  • Best Practices for 3M (08155) Quick Fix Adhesive

    *See Terms of Use Below

    1. Surface Preparation

      Surfaces must be clean and dry.

      Use 3M™ General Purpose Adhesive Cleaner P.N. 08984 to remove grease, oil, dust and mold release

    2. Application

      Only small drops are needed. Apply only to close fitting parts-not a gap filler.

      Apply one drop per one square inch. Mate the second surface to first

      rub the two surfaces together to spread the adhesive.

    3. Curing

      Cure will start within 5-60 seconds. Handling strength is usually obtained within 1-5 minutes and highest strength within 12-24 hours.

  • Comparable Materials for 3M (08155) Quick Fix Adhesive

    *See Terms of Use Below

    Spec Engine® Results

    • PermaBond
      108(PermaBond)

      An intermediate viscosity cyanoacrylate that is used to bond through intermediate gaps. It is fast setting and suitable for use on plastics, rubber and metals.

    • PermaBond
      795(PermaBond)

      Surface insensitive – cures rapidly on most surfaces, wide range of viscosities, fast setting, rapid cure.

    • PermaBond
      170(PermaBond)

      Medium viscosity, maximum gap fill. Fast setting with rapid development of high strength.

    • Compare All

    Closest Results from this Manufacturer

    • 3M
      PR03(3M)

      A medium-high viscosity low odor cyanoacrylate that has good gap-filling capability.

    • Compare All
  Download Technical Data Sheet   Save This Material   Compare View Saved Items

Popular Articles

Cyanoacrylate 101

Read Article

Cyanoacrylate 202

Read Article

Testing the effectiveness of surface treatments

Read Article

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Read Article

Sponsored Articles

Unique Advantages of Contact Adhesives

Read Article

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Read Article

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Read Article

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Read Article

Featured Ads

Top Catalog Pages for 3M (08155) Quick Fix Adhesive

All 3M Materials
View Now

Gluespec Poll

Who do you read or follow for engineering news and entertainment?
Viscosity Test Methods
Viscosity Test Method
Thin fluid
400 to 600 cPs Brookfield Viscometer, RVF #4 @ 20 RPM
High Temperature Resistance Test Methods
High Temperature Resistance Test Method
71°C deg F
Low Temperature Resistance Test Methods
Low Temperature Resistance Test Method
Density Test Methods
Density Test Method
8.7 to 9.0 (lbs/Gallon) (Appx.)
Flash Point Test Methods
Flash Point Test Method
80.0°C Cures during test
% Solids Test Methods
% Solids Test Method
100 % Appx.