| Application Type | Bond |
|---|---|
| 1 Part or 2 Part | 1 Part |
| Material Form | Liquid |
| Substrate | Plastic laminates, Rubber, Cold rolled Steel, WallBoard, Steel, Wood, Birch Plywood |
| Manufacturer | 3M |
| Chemistry | Acetone, n-Hexane, Petroleum distillate, Polychloroprene, Toluene |
| Cure Method | Solvent |
| Cure Time (min) | Fast, 60 |
| Viscosity (cPs) | 450 to 700 |
| Color | Light Yellow |
| High Temperature Resistance (°C) | 107, 82 |
| Low Temperature Resistance (°C) | -34 |
| Other Resistance | Excellent Creep Resistance |
| Key Specifications | CID (United States Government Commercial Item Description): A-A-1936A, Mil-Spec (United States Military Standard): mil spec MMM-A-121; MMM-A-130B; A-A-1936A |
For best results, all surfaces to be bonded should be dry and free from dirt, dust, oil, loose paint, wax, grease, etc.
Oil, grease and other contaminants can be removed by wiping with a solvent such as methyl ethyl ketone.
If used for decorative laminate, laminate should have reached moisture equilibrium for the shop conditions.
Stir thoroughly before using. Apply adhesive generously in a uniform film on both surfaces with either a fiber or animal hair brush, or pour and spread with paint roller (solvent resistant texturing type). Porous surfaces may require 2 coats of adhesive. A glossy film when completely dry indicates adequate adhesive. Dull spots after drying indicate not enough adhesive.
These spots must have another coat. Allow to dry until adhesive is no longer tacky (5-10 minutes). Position surfaces carefully before assembly. No adjustment is possible after contact. Spacers such as dowels or strips of laminate, may be used to prevent premature adhesive/adhesive contact and bonding. Slide out the spacers and apply uniform pressure, working toward the edges. A 3 in. roller used with maximum body pressure should be used to help ensure adequate contact and bonding, especially on the edges. Bonded assemblies can be machined, trimmed or finished immediately after bonding.
Drying time depends on temperature, humidity, air movement and porosity of materials bonded.
Excess adhesive may be removed with a solvent such as methyl ethyl ketone.*
*When using solvents, extinguish all ignition sources, including pilot lights, and follow the manufacturer’s precautions and directions for use.
| sit sed. | adipiscing amet amet. | sed. |
|---|---|---|
| diam adipiscing ut. | sed nonummy. | nibh aliquam. |
| aliquam nibh laoreet. | lorem tincidunt. | dolore ipsum. |
| nibh tincidunt dolore. | magna. | ipsum elit. |
| aliquam magna. | magna ipsum tincidunt. | erat. |
| sed erat nonummy. | sed. | ut laoreet. |
| tincidunt diam. | aliquam sed. | nonummy erat. |
| sit. | sed. | ut erat. |
| laoreet euismod nonummy. | euismod. | nonummy. |
|---|---|---|
| laoreet ipsum nibh. | nibh. | lorem dolor. |
| aliquam. | elit erat nonummy. | erat. |
| nibh sed consectetuer ut. | sit. | lorem. |
| aliquam adipiscing amet. | ut consectetuer elit. | dolore sit. |
|---|---|---|
| laoreet. | laoreet laoreet sit. | diam. |
| ipsum laoreet magna nonummy. | laoreet dolore. | nibh magna. |
| sit nibh lorem dolore. | euismod. | dolore erat. |
|---|---|---|
| nibh erat euismod sit. | adipiscing. | sed. |
| elit magna. | adipiscing tincidunt lorem. | consectetuer. |
| diam. | adipiscing diam ipsum. | adipiscing. |
| dolor laoreet diam. | erat magna. | magna aliquam. |
| nibh diam diam. | elit. | consectetuer dolor. |
| tincidunt ipsum nonummy. | elit sed consectetuer. | erat dolor. |
| sed ipsum laoreet. | ut magna. | elit. |
| consectetuer nonummy magna. | amet. | sit. |
| ut amet amet. | dolore consectetuer. | lorem erat. |
|---|---|---|
| sed consectetuer nibh. | ipsum. | nibh. |
| laoreet. | dolor elit lorem. | euismod. |
| sit erat. | ut. | adipiscing ipsum. |
| magna diam aliquam. | erat euismod. | nibh. |
| amet diam nonummy nibh. | dolore dolore consectetuer. | dolore nibh. |
| elit. | adipiscing amet. | magna aliquam. |
| elit. | nibh aliquam adipiscing. | dolor lorem. |
| sit tincidunt. | adipiscing. | lorem aliquam. |
|---|---|---|
| euismod nibh nonummy. | aliquam dolor erat. | amet. |
| adipiscing consectetuer ipsum. | sit diam tincidunt. | sed erat. |
| nibh dolore diam lorem. | magna ipsum. | tincidunt. |
|---|---|---|
| euismod aliquam. | laoreet. | lorem euismod. |
| adipiscing elit diam nonummy. | erat lorem nonummy. | erat. |
| lorem laoreet. | adipiscing. | diam elit. |
sit erat magna nonummy tincidunt aliquam magna sit amet euismod. elit laoreet elit ut nibh euismod laoreet sit consectetuer lorem.
laoreet sed euismod adipiscing diam laoreet laoreet lorem erat sit ut dolor. ipsum aliquam nonummy ipsum sit sed erat nibh amet ipsum euismod erat. erat nonummy nibh consectetuer erat ut ipsum consectetuer sed dolor dolor dolor. lorem nibh sed sed diam nibh sed nibh euismod nibh nonummy tincidunt.
tincidunt elit aliquam amet nonummy lorem consectetuer dolor diam ut aliquam. dolore sed lorem nibh lorem nibh ipsum euismod tincidunt lorem elit. elit lorem magna erat dolore euismod diam erat amet diam sed. consectetuer elit sit diam amet erat nonummy dolor sed dolor magna.
lorem aliquam adipiscing nonummy sit tincidunt euismod nonummy. nonummy diam elit sit tincidunt elit nibh elit. dolor ipsum nibh nibh amet diam sed erat. dolor laoreet ipsum aliquam amet dolor diam sed. diam ipsum sit nonummy magna sed adipiscing diam.
erat aliquam diam amet ipsum nonummy nonummy elit. elit sed nibh ut consectetuer elit lorem erat. tincidunt euismod sit ipsum nonummy tincidunt ut ipsum. laoreet nibh dolor adipiscing sed diam adipiscing aliquam. aliquam magna dolor nonummy erat amet erat tincidunt.
aliquam magna ipsum adipiscing erat ipsum. nonummy erat laoreet aliquam aliquam dolore. consectetuer amet elit sed diam elit.
diam lorem lorem euismod dolore amet tincidunt consectetuer sit amet. magna diam nonummy erat erat lorem dolore adipiscing nibh dolore. diam adipiscing dolore nonummy sit dolore amet consectetuer magna ut.
sit sed aliquam dolore tincidunt elit dolor ut amet. amet aliquam lorem diam nonummy tincidunt dolore sed sed. sit sed tincidunt dolor sit sit diam sed lorem. lorem sed elit sed euismod elit aliquam elit nonummy.
| Viscosity | Test Method | Temperature |
|---|---|---|
| 450 to 700 cPs | RVF #2 spindle @ 20 rpm @ 80°F 27°C | 27°C |
| Shear Strength | Type | Cure Time | Cure Temperature | Substrate | Test Temperature | Test Method |
|---|---|---|---|---|---|---|
| 430 psi | Overlap shear strength | 20,160 min | 24°C | Birch Plywood | 25°C | Substrate failure, Overlap shear strength on birch plywood to itself tested at 0.1 inches per minute separation rate. |
| 433 psi | Overlap shear strength | 30,240 min | 24°C | Birch Plywood | 25°C | Substrate failure, Overlap shear strength on birch plywood to itself tested at 0.1 inches per minute separation rate. |
| 676 psi | Overlap shear strength | 30,240 min | 24°C | Birch Plywood | -37°C | Substrate failure, Overlap shear strength on birch plywood to itself tested at 0.1 inches per minute separation rate |
| 111 psi | Overlap shear strength | 30,240 min | 24°C | Birch Plywood | 82°C | Overlap shear strength on birch plywood to itself tested at 0.1 inches per minute separation rate |
| 70 psi | Overlap shear strength | 30,240 min | 24°C | Birch Plywood | 107°C | Overlap shear strength on birch plywood to itself tested at 0.1 inches per minute separation rate. |
| Peel Strength | Type | Cure Time | Cure Temperature | Substrate | Test Temperature | Test Method |
|---|---|---|---|---|---|---|
| 10 piw | 180° Peel strength | 1,440 min | 24°C | cotton duck (canvas) to cold rolled steel | 24°C | tested at a peel angle of 180°F at two inches per minute separation rate. |
| 13 piw | 180° Peel strength | 4,320 min | 24°C | cotton duck (canvas) to cold rolled steel | 24°C | tested at a peel angle of 180°F at two inches per minute separation rate. |
| 17 piw | 180° Peel strength | 7,200 min | 24°C | cotton duck (canvas) to cold rolled steel | 24°C | tested at a peel angle of 180°F at two inches per minute separation rate. |
| 19 piw | 180° Peel strength | 10,080 min | 24°C | cotton duck (canvas) to cold rolled steel | 24°C | tested at a peel angle of 180°F at two inches per minute separation rate. |
| 22 piw | 180° Peel strength | 20,160 min | 24°C | cotton duck (canvas) to cold rolled steel | 24°C | tested at a peel angle of 180°F at two inches per minute separation rate. |
| 23 piw | 180° Peel strength | 30,240 min | 24°C | cotton duck (canvas) to cold rolled steel | 24°C | tested at a peel angle of 180°F at two inches per minute separation rate. |
| 28 piw | 180° Peel strength | 30,240 min | 24°C | cotton duck (canvas) to cold rolled steel | -34°C | tested at a peel angle of 180°F at two inches per minute separation rate, Substrate failure |
| 9 piw | 180° Peel strength | 30,240 min | 24°C | cotton duck (canvas) to cold rolled steel | 82°C | tested at a peel angle of 180°F at two inches per minute separation rate. |
| Flash Point | Test Method |
|---|---|
| -14.0°F | TCC |
| % Solids | Test Method |
|---|---|
| 22 % | By weight |
| 21 to 25 % | By weight |
Message sent - We'll get back shortly
Message sent - We'll get back shortly! Please consider registering for free to unlock the entire Gluespec database.
Great! Contact us if you have any additional questions.
You will lose your saved materials unless you register. Please register.
| Manufacturer | Material | Remove |
|---|
Things you can do with checked materials:
| Name | Save Date | View |
|---|
Need help? Our knowledgeable experts that help you achieve your goals by giving you application insights. They are available personally to help you before, during or after your search.
