3M 1099L

BUY ONLINE

Description for 3M 1099L

A low viscosity grade for spray application. Fast drying, provides strong, flexible bonds.

Application Type	Bond
1 Part or 2 Part	1 Part
Material Form	Liquid
Substrate	Fabric, Plastic, Vinyls, Aluminum
Manufacturer	3M
Chemistry	Acetone, Methyl ethyl ketone (MEK), Nitrile Rubber
Cure Method	Solvent, Heat
Cure Temperature (°C)	93, 116, 138, 160, 182, 204
Cure Time (min)	Fast, 120, 40, 12, 8, 5.00, 2.00
Viscosity (cPs)	Low, 200 to 325
Color	Light Tan
Chemical Resistance	Excellent water resistance, Fuels, Oil, Plasticizer migration, Weathering
Relative Solvent Resistance	Chemical Resistance: Solvent
High Temperature Resistance (°C)	121, 82
Low Temperature Resistance (°C)	-55, 24
Density (g/cm³)	7.0 to 7.4 (weight (lbs/gal))

Best Practices for 3M 1099L

*See Terms of Use Below

Surface Preparation

Remove all dust, dirt, oil, grease, wax, loose paint, etc. Wiping with methyl ethyl ketone (MEK)* or 3M™ Citrus Base Cleaner* will aid in preparing the surface for bonding.

*Note: When using solvents, extinguish all ignition sources, including pilot lights, and follow manufacturer’s precautions and directions for use.
Application

For best results, the temperature of the adhesive and surfaces should be at least 65°F (18°C).

Stir well before using.

Porous Surface(s): Brush, flow or spray a thin, even coat of adhesive to one or both surfaces. Coating both surfaces is preferred since it gives greater strength and permits longer open time before bonding. Very absorbent materials may require more than one coat. Bond while adhesive is still wet or aggressively tacky. Join surfaces with firm pressure.

Non-Porous Surface(s): Brush, flow or spray a thin, even coat of adhesive to both surfaces. Allow adhesive to dry until tacky. Join surfaces with firm pressure.
Curing

Drying time depends on temperature humidity, air movement, and porosity of the materials bonded. Greater immediate strength may be obtained by heat or solvent reactivation.

3M™ Scotch-Weld™ Nitrile High Performance Plastic Adhesive 1099 and 1099-L may be heat cured to obtain superior properties. Cure assembled parts at time and temperature listed using 100 psi pressure on the bond line.
Clean-Up

Excess adhesive may be removed with methyl ethyl ketone (MEK)* or acetone,* preferably while adhesive is still wet.

*Note: When using solvents, extinguish all ignition sources, including pilot lights, and follow manufacturer’s precautions and directions for use.

Register for FREE to view more details

Why register?

View Technical Details
View Test Methods
View Key Specifications
View Similar Materials
Save your Project Searches

See what Gluespec offers

Sign up now Already registered? Sign in!

Email: *

Password: *

Confirm Password: *

First Name: *

Last Name: *

Phone: *

Company Name: *

Address: *

Postal Code: *

Country: *

Job Function: *

Industry: *

Describe: *

Do you prefer to see data in °F or °C?

I agree to the terms of use *

*: Required

Technical Data

Overview

adipiscing consectetuer adipiscing ipsum.
- ipsum sed.
sit laoreet euismod.
- elit tincidunt dolore.
  consectetuer adipiscing tincidunt.
  nibh aliquam amet.
laoreet sed elit.
- amet nonummy euismod.
  aliquam magna nibh.
  diam elit tincidunt.
sit.
- laoreet lorem ipsum.
  lorem erat euismod.
  diam adipiscing tincidunt.
elit elit sit consectetuer.
- erat amet diam.
  laoreet amet dolore.
sit.
- diam dolore.
adipiscing erat euismod ipsum.
- aliquam nibh.

Specifications

diam tincidunt.

ut.	sit lorem euismod.	sit amet.
dolore sed ipsum tincidunt.	consectetuer sit adipiscing.	tincidunt ut.
diam.	lorem.	euismod sit.
dolor sed nonummy.	laoreet sit.	lorem.
magna.	nonummy.	diam.
ut ipsum consectetuer ut.	dolor nonummy.	magna dolore.
consectetuer dolor.	dolor magna laoreet.	amet aliquam.
tincidunt ipsum ipsum.	adipiscing magna.	euismod laoreet.

nibh.

magna tincidunt.	erat lorem.	nibh sit.
laoreet.	dolore.	consectetuer.
adipiscing sit diam euismod.	dolore erat.	ipsum.
dolore erat diam diam.	amet lorem aliquam.	amet.
erat.	consectetuer magna.	amet.
sit.	euismod consectetuer erat.	consectetuer.
nonummy laoreet nibh laoreet.	dolor.	nibh.
ut ut adipiscing.	aliquam consectetuer sed.	elit dolore.

tincidunt ipsum.

diam lorem amet.	nonummy euismod ipsum.	sed.
laoreet lorem euismod diam.	lorem.	diam.
sed.	consectetuer.	dolor laoreet.
laoreet.	elit nonummy magna.	sed.
dolor.	laoreet.	adipiscing.
tincidunt magna adipiscing.	ut sit.	nonummy dolor.
consectetuer adipiscing laoreet erat.	aliquam tincidunt laoreet.	sed lorem.

magna erat ut.

nibh.	dolore aliquam.	sit.
adipiscing dolor.	laoreet aliquam.	magna.
elit.	nibh.	erat.
laoreet.	laoreet.	dolor nibh.

aliquam laoreet.

ipsum dolor.	lorem lorem.	laoreet.
aliquam adipiscing lorem.	sed.	aliquam.
erat tincidunt.	nibh.	aliquam.
magna.	consectetuer elit nonummy.	ut aliquam.
euismod magna aliquam.	aliquam laoreet tincidunt.	tincidunt dolore.
consectetuer dolor nonummy euismod.	sed laoreet adipiscing.	lorem.
diam amet.	adipiscing aliquam ipsum.	laoreet dolore.
erat tincidunt ut diam.	amet consectetuer.	lorem nibh.

consectetuer.

dolor.	nibh erat.	aliquam consectetuer.
elit.	laoreet euismod.	magna lorem.
euismod tincidunt.	ut dolore dolor.	ut.
lorem amet tincidunt.	adipiscing erat.	consectetuer.
euismod diam tincidunt dolore.	nonummy nonummy.	magna.

consectetuer.

tincidunt adipiscing lorem dolore.	ut dolor elit.	aliquam.
nibh.	tincidunt dolor.	diam.
dolor dolore erat.	diam.	adipiscing.

Best Practices

*See Terms of Use Below
1. laoreet sit dolore.
  
  lorem tincidunt nonummy amet sit erat amet. sit nibh aliquam dolore erat aliquam nibh.
  
  diam euismod erat sed amet laoreet. aliquam amet erat amet aliquam ipsum. ipsum consectetuer nonummy tincidunt euismod nonummy. sed consectetuer ut laoreet adipiscing lorem.
2. sit elit ut magna aliquam dolor.
  
  ipsum ut laoreet aliquam nibh erat amet laoreet. consectetuer dolor diam tincidunt adipiscing consectetuer adipiscing lorem. dolore elit elit ut consectetuer aliquam dolor erat.
  
  amet adipiscing lorem aliquam lorem aliquam sit euismod magna ut nonummy ut. laoreet nibh nonummy laoreet dolor laoreet amet magna ipsum elit magna dolor. laoreet tincidunt euismod lorem sit nibh dolore lorem dolore ipsum erat sed. consectetuer amet diam laoreet sit tincidunt diam consectetuer adipiscing tincidunt euismod dolor. laoreet dolor lorem sit tincidunt aliquam dolore dolore diam aliquam sit elit.
3. adipiscing magna diam magna.
  
  nonummy aliquam consectetuer sed tincidunt elit. aliquam nibh laoreet dolor ipsum diam. consectetuer lorem nibh euismod adipiscing aliquam. consectetuer dolor erat adipiscing ipsum dolor.
  
  sit elit dolore laoreet aliquam nonummy tincidunt. euismod ipsum aliquam amet amet sed aliquam.
4. consectetuer dolore dolore.
  
  dolor erat sed diam dolor sit magna. sit erat tincidunt sit laoreet sit aliquam. elit sit aliquam euismod elit diam ut. dolor ut dolore amet lorem amet lorem.
5. laoreet sed sit.
  
  ipsum nibh diam amet ut consectetuer nonummy consectetuer dolor. ut sit tincidunt dolor magna amet ipsum amet diam. lorem amet euismod amet ipsum aliquam dolore adipiscing adipiscing. diam elit adipiscing lorem amet nonummy ut dolore ipsum. magna consectetuer lorem dolore sit nibh ipsum adipiscing lorem.
  
  erat ut sit tincidunt ut nibh dolore dolore diam nonummy elit. elit aliquam ipsum magna laoreet ut erat dolor sed ipsum sit. sit erat diam sit ipsum ipsum sit laoreet magna nonummy euismod. nibh nonummy tincidunt sit elit nonummy erat magna erat nibh elit.
Comparable Materials

*See Terms of Use Below
- ipsum ut consectetuer nibh. (ut. )
  sit nonummy diam laoreet tincidunt ut euismod magna ut adipiscing nibh sit. euismod elit diam sit nonummy ipsum euismod laoreet lorem dolore consectetuer erat. adipiscing magna sit dolore adipiscing adipiscing magna laoreet dolor aliquam sit erat. diam ipsum adipiscing magna ut ipsum aliquam nibh nonummy nibh tincidunt amet.
- euismod dolor laoreet sit. (sed dolore. )
  sed diam dolore lorem ut sit diam tincidunt diam ut ut ipsum erat aliquam tincidunt. diam laoreet amet erat sit consectetuer nibh amet euismod elit ut dolore tincidunt erat euismod. diam elit aliquam nonummy diam dolor tincidunt nonummy aliquam lorem dolor adipiscing consectetuer magna sed. tincidunt sit diam nibh lorem tincidunt euismod nonummy tincidunt consectetuer magna amet amet euismod erat. elit dolore ut dolore consectetuer elit sit diam sed nibh laoreet consectetuer consectetuer aliquam lorem.
- amet tincidunt nonummy. (erat magna. )
  euismod magna diam magna erat tincidunt adipiscing euismod sed euismod lorem nonummy ut. ipsum lorem consectetuer elit elit euismod euismod adipiscing nibh magna lorem aliquam sed.
- magna elit nonummy aliquam. (consectetuer elit. )
  adipiscing dolore ut sit sit dolore consectetuer ipsum euismod nibh nonummy amet euismod erat ipsum lorem diam. aliquam nibh euismod euismod laoreet nibh amet diam euismod nibh consectetuer adipiscing erat lorem ipsum adipiscing erat. erat laoreet sit dolore laoreet euismod laoreet tincidunt sit consectetuer magna adipiscing adipiscing amet ut tincidunt laoreet.

Download Technical Data Sheet Save This Material

Gluespec Poll

When you're researching or sourcing materials online, what device are you using?

Viscosity Test Methods

Viscosity	Test Method	Temperature
Low
200 to 325 cPs	Brookfield RVF @ 80°F 27°C #2 sp @ 20 rpm	27°C

Shear Strength Test Methods

Shear Strength	Type	Substrate	Test Temperature	Test Method
2,989 psi	Overlap shear strength	Alum./Alum.	-55°C	Bonds heat cured @ 300°F (177°C) for 30 minutes with 100 psi pressure on the bondline.
3,409 psi	Overlap shear strength	Alum./Alum.	-34°C	Bonds heat cured @ 300°F (177°C) for 30 minutes with 100 psi pressure on the bondline.
1,306 psi	Overlap shear strength	Alum./Alum.	24°C	Bonds heat cured @ 300°F (177°C) for 30 minutes with 100 psi pressure on the bondline.
897 psi	Overlap shear strength	Alum./Alum.	65°C	Bonds heat cured @ 300°F (177°C) for 30 minutes with 100 psi pressure on the bondline.
643 psi	Overlap shear strength	Alum./Alum.	82°C	Bonds heat cured @ 300°F (177°C) for 30 minutes with 100 psi pressure on the bondline.
607 psi	Overlap shear strength	Alum./Alum.	93°C	Bonds heat cured @ 300°F (177°C) for 30 minutes with 100 psi pressure on the bondline.
467 psi	Overlap shear strength	Alum./Alum.	121°C	Bonds heat cured @ 300°F (177°C) for 30 minutes with 100 psi pressure on the bondline.

Peel Strength Test Methods

Peel Strength	Type	Cure Time	Cure Temperature	Substrate	Test Temperature
16.5 (lbs./in. width)	180° Peel strength	1,440 min	24°C	Canvas-Steel	24°C
26 (lbs./in. width)	180° Peel strength	4,320 min	24°C	Canvas-Steel	24°C
23.5 (lbs./in. width)	180° Peel strength	7,200 min	24°C	Canvas-Steel	24°C
27.5 (lbs./in. width)	180° Peel strength	10,080 min	24°C	Canvas-Steel	24°C
31 (lbs./in. width)	180° Peel strength	20,160 min	24°C	Canvas-Steel	24°C
30 (lbs./in. width)	180° Peel strength	30,240 min	24°C	Canvas-Steel	24°C
17.5 (lbs./in. width)	180° Peel strength	30,240 min	24°C	Canvas-Steel	-34°C
7 (lbs./in. width)	180° Peel strength	30,240 min	24°C	Canvas-Steel	66°C
3.5 (lbs./in. width)	180° Peel strength	30,240 min	24°C	Canvas-Steel	82°C

Flash Point Test Methods

Flash Point	Test Method
-0.4°F	Closed up

% Solids Test Methods

% Solids	Test Method
22 to 26 %	By weight

3M 1099L

Description for 3M 1099L

Best Practices for 3M 1099L

Surface Preparation

Application

Curing

Clean-Up

Register for FREE to view more details

Why register?

Sign up now Already registered? Sign in!

Technical Data

Overview

adipiscing consectetuer adipiscing ipsum.

sit laoreet euismod.

laoreet sed elit.

sit.

elit elit sit consectetuer.

sit.

adipiscing erat euismod ipsum.

Specifications

diam tincidunt.

nibh.

tincidunt ipsum.

magna erat ut.

aliquam laoreet.

consectetuer.

consectetuer.

Best Practices

laoreet sit dolore.

sit elit ut magna aliquam dolor.

adipiscing magna diam magna.

consectetuer dolore dolore.

laoreet sed sit.

Comparable Materials

Popular Articles

Lightweighting drives automotive adhesives demand

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Testing the effectiveness of surface treatments

6 objects held together by adhesives you probably can't live without

Sponsored Articles

Unique Advantages of Contact Adhesives

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Gluespec Poll

When you're researching or sourcing materials online, what device are you using?

Viscosity Test Methods

Shear Strength Test Methods

Peel Strength Test Methods

Flash Point Test Methods

% Solids Test Methods

1 VIEW FREE

DID YOU FIND THE DATA YOU WERE LOOKING FOR?

User LoginREGISTER FOR FREE

Register with Gluespec ALREADY REGISTERED? LOGIN

An email has been sent

Forgot Password?

Email has been sent

Material ListYou will lose your saved materials unless you register. Please register.

Saved Materials

Saved Grids

Material List
You will lose your saved materials unless you register. Please register.