• Description for 3M 1300

    • Bonds neoprene, SBR, butyl and other types of rubber to various substrates • Bonding Range up to 12 minutes • A lower solids viscosity • Easier brushing and sprayability •

    *See Terms of Use Below

    Chemical Resistance Chemical Resistance: Aromatic solvents, Chemical Resistance: Ketone
    Application Type Bond, Gaskets
    1 Part or 2 Part 1-Part
    Material Form Liquid
    Substrate Metal, Neoprene, Plastic, Rubber, Steel, Birch, Porous, Butyl Rubber, SBR, Canvas Steel, Wood
    Manufacturer 3M
    Chemistry Methyl ethyl ketone, Solvent-Based, Petroleum distillate, Polychloroprene, Toluene
    Application Method Spatula, Trowel
    Cure Method Solvent
    Application Temperature (°F) 64
    Cure Time (min) Fast drying, <4.00
    Viscosity (cPs) 1,500 to 4,000, Lower
    Color Yellow
    High Temperature Resistance (°C) Excellent Heat Resistance, 149
    Low Temperature Resistance (°C) -34
    Density (g/cm³) Net wt. (Approx.) 7.1 to 7.5 (lbs/gal))
    Key Specifications Mil-Spec (United States Military Standard): MMM-A-121
  • Technical Data for 3M 1300

    Overview
    • Chemical Resistance
      • Chemical Resistance : Relative Solvent Resistance - Aromatic solvents, Ketone
    • Application Type
    • 1 Part or 2 Part
      • 1-Part
    • Material Form
      • Liquid
    • Substrate
      • Porous Substrates - Porous
      • Metal
      • Steel - Canvas Steel
      • Plastic
      • Rubber
      • Neoprene
      • Nitrile Rubber - Butyl Rubber
      • Styrene Butadiene Rubber (SBR) - SBR
      • Wood - Birch
      • Other - Reclaim
    • Chemistry
      • Solvent-Based
      • Other - Methyl ethyl ketone, Petroleum distillate, Polychloroprene, Toluene
    • Application Method
      • Dispenser - Application equipment
      • Flow - Flow equipment
      • Spatula/Trowel - Spatula, Trowel
    • Cure Method
      • Solvent
    • Color
      • Yellow
    • Key Specifications
      • Mil-Spec (United States Military Standard) : MMM-A-121
    Specifications
    Cure Specs
    Application Temperature (°F) 64
    Cure Time (min) Fast drying, <4.00
    Viscosity (cPs) 1,500 to 4,000, Lower Test Method
    Bond Strength
    General Bond Strength (psi) High immediate strength
    Peel Strength (piw) 18, 48, 51, 52, 30, 20, 49, 33, 26 Test Method
    Shear Strength (psi) 343, 549, 195, 136, 85, 85 Test Method
    Material Resistance
    High Temperature Resistance (°C) Excellent Heat Resistance, 149
    Low Temperature Resistance (°C) -34
    Other Properties
    Flash Point (°F) -14.8
    % Solids (%) Lower, 37, 34 Test Method
    Density (g/cm³) Net wt. (Approx.) 7.1 to 7.5 (lbs/gal))
    Business Information
    Shelf Life Details Storage: Store product at 60-80°F (16-27°C) for maximum storage life. Higher temperatures can reduce normal storage life. Lower temperatures can cause increased viscosity of a temporary nature. Rotate stock on a “first in-first out” basis.;Shelf Life: When stored at the recommended temperature in the original, unopened container this product has a shelf life of 15 months from date of shipment.
    Shelf Life Temperature (°F) 61 to 81
    Shelf Life Type from date of shipment
    Shelf Life (mon) 15
  • Best Practices for 3M 1300

    *See Terms of Use Below

    1. Surface Preparation

      Remove all dust, dirt, oil, grease, wax, loose paint, etc. Wiping with a solvent such as methyl ethyl ketone (MEK)* will aid in preparing the surface for bonding.

    2. Application

      For best results the temperature of the adhesive and surfaces to be bonded should be at least 65°F (18°C). If stored below 30°F (-1°C), allow adhesive to warm to room temperature by placing in a warm room only (do not exceed 120°F [49°C]) followed by thorough agitation.

      Stir well before using. Brush, flow or spray a thin, uniform coating of adhesive to each surface. A coating of 2.5 gms to 3.5 gms/ft.2 dry weight per surface is recommended. Porous surfaces may require more than one coat. A uniform, glossy film indicates sufficient adhesive.

    3. Curing

      Allow adhesive to dry until no longer wet (maximum dry time about 4 minutes).

      Once dry, these adhesives have a short bonding range (up to 8 to 12 minutes).

      Position surfaces carefully before assembly. Bonding is immediate upon contact. Apply sufficient pressure to ensure good contact between coated surfaces. Bonded parts may be handled immediately.

    4. Clean-Up

      Use a solvent such as 3M™ Scotch-Weld™ Solvent No. 2* or methyl ethyl ketone (MEK)* to clean brushes immediately after use. Excess adhesive may be removed from other surfaces with 3M™ Citrus Base Cleaner* or equivalent.

      *Note: When using solvents, extinguish all ignition sources, including pilot lights, and follow manufacturer’s precautions and directions for use.

  • Comparable Materials for 3M 1300

    *See Terms of Use Below

    Spec Engine® Results

Popular Articles

Lightweighting drives automotive adhesives demand

Read Article

6 objects held together by adhesives you probably can't live without

Read Article

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Read Article

Testing the effectiveness of surface treatments

Read Article

Sponsored Articles

Unique Advantages of Contact Adhesives

Read Article

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Read Article

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Read Article

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Read Article

Featured Ads

Gluespec Poll

Who do you read or follow for engineering news and entertainment?
Viscosity Test Methods
Viscosity Test Method Temperature
1,500 to 4,000 cPs Brookfield Viscometer:RVF #4 sp @ 20 rpm@80°F 27°C 27°C
Lower
Peel Strength Test Methods
Peel Strength Type Cure Time Cure Temperature Substrate Test Temperature
18 piw 180° Peel strength 1,440 min 24°C Canvas-Steel 24°C
48 piw 180° Peel strength 4,320 min 24°C Canvas-Steel 24°C
51 piw 180° Peel strength 7,200 min 24°C Canvas-Steel 24°C
52 piw 180° Peel strength 10,080 min 24°C Canvas-Steel 24°C
30 piw 180° Peel strength 20,160 min 24°C Canvas-Steel 24°C
20 piw 180° Peel strength 30,240 min 24°C Canvas-Steel 24°C
49 piw 180° Peel strength >30,240 min 24°C Canvas-Steel -34°C
33 piw 180° Peel strength >30,240 min 24°C Canvas-Steel 66°C
26 piw 180° Peel strength >30,240 min 24°C Canvas-Steel 82°C
Shear Strength Test Methods
Shear Strength Type Cure Time Cure Temperature Substrate Test Temperature
343 psi Overlap shear strength 20,160 min 25°C 1/8" Birch/1/8" Birch -34°C
549 psi Overlap shear strength 20,160 min 25°C 1/8" Birch/1/8" Birch 24°C
195 psi Overlap shear strength 20,160 min 25°C 1/8" Birch/1/8" Birch 65°C
136 psi Overlap shear strength 20,160 min 25°C 1/8" Birch/1/8" Birch 82°C
85 psi Overlap shear strength 20,160 min 25°C 1/8" Birch/1/8" Birch 93°C
85 psi Overlap shear strength 20,160 min 25°C 1/8" Birch/1/8" Birch 110°C
% Solids Test Methods
% Solids Test Method
Lower
37 % By weight
34 % By weight