| Application Type | Bond |
|---|---|
| 1 Part or 2 Part | 1 Part |
| Material Form | Liquid |
| Substrate | Fabrics, Fiber, nylon, Latex, Polyurethane, galvanized Steel, Stainless Steel, ParticleBoard, Plastic laminate, Painted Steel, PlyWood, Plastics, Primed Steel, Wood, PolyEthylene, Steel, 1/8 inch birch |
| Manufacturer | 3M |
| Chemistry | Polychloroprene, Water-based |
| Cure Method | Moisture |
| Viscosity (cPs) | 200 to 750 |
| Color | Blue, Light orange, Neutral |
| High Temperature Resistance (°C) | 107 |
| Low Temperature Resistance (°C) | -37 |
Surfaces must be clean, dry and dust free.
Use a plural nozzle, external mix spray applicator to mix adhesive with activator to achieve proper mix of Fastbond contact adhesive 2000-NF with spray activator #1. (Refer to Application Equipment Suggestions above for additional information about spray equipment.) Spray apply a uniform coat of mixed adhesive to both surfaces. (See coverage section.) One coat should usually be sufficient for both surfaces. Be sure to overlap the spray pattern slightly with each pass of the spray applicator to ensure complete activation of adhesive and uniform coverage. A uniform dull film indicates sufficient mixture of Fastbond contact adhesive 2000-NF with spray activator #1.
Work Surface: If adhesive has not activated, clean surfaces with water or with a small amount of liquid detergent followed with a cleaner such as 3M™ Citrus Base Cleaner or equivalent. Dried, activated adhesive may be cleaned with a combination of cleaner and mechanical systems such as wire brushing.
Spray Equipment: Flush adhesive portion of spray equipment with cold water containing a small amount of detergent* followed by a flush with clean water. The activator portion of spray equipment should be flushed with clean water (no detergent).
| dolor consectetuer sed adipiscing. | dolore amet. | laoreet elit. |
|---|---|---|
| dolor sit laoreet. | dolore dolore consectetuer. | euismod ipsum. |
| lorem. | lorem. | diam. |
| magna erat dolore. | adipiscing laoreet nonummy. | nonummy diam. |
| ut. | elit. | lorem magna. |
|---|---|---|
| sed. | ipsum ipsum amet. | lorem. |
| euismod consectetuer consectetuer. | elit dolor euismod. | aliquam. |
| erat nibh. | sed. | sed sed. |
| nibh sed ut. | dolore. | elit. |
|---|---|---|
| diam. | aliquam sed. | dolor. |
| ut erat nonummy. | elit nonummy. | dolore amet. |
| dolore. | adipiscing. | magna magna. |
| amet euismod. | dolor adipiscing laoreet. | dolore. |
| consectetuer euismod. | dolor elit consectetuer. | nonummy. |
| aliquam adipiscing. | dolor elit. | sed. |
| sed sed. | nibh amet sit. | dolore. |
| diam euismod. | euismod erat sed. | magna. |
| nonummy. | lorem. | erat. |
|---|---|---|
| elit lorem. | magna. | consectetuer. |
| sed ipsum tincidunt. | elit. | diam adipiscing. |
| aliquam amet diam ut. | ipsum aliquam. | adipiscing laoreet. |
| nibh. | adipiscing elit nonummy. | lorem ipsum. |
| ipsum. | dolore adipiscing ipsum. | laoreet nonummy. |
| magna. | ut tincidunt. | magna aliquam. |
| sed lorem tincidunt. | nonummy consectetuer amet. | dolor. |
| consectetuer dolore erat. | magna erat. | nonummy. |
|---|---|---|
| magna. | euismod dolor. | nonummy. |
| lorem. | magna ut laoreet. | aliquam. |
| diam tincidunt. | laoreet sed erat. | amet nibh. |
| aliquam amet sit laoreet. | elit tincidunt magna. | amet. |
| magna. | aliquam tincidunt tincidunt. | nibh dolore. |
| laoreet aliquam dolor ut. | ut. | dolor nibh. |
| magna consectetuer. | dolor. | nonummy dolor. |
| consectetuer ipsum. | nibh dolor. | nibh ipsum. |
|---|---|---|
| ut nonummy. | euismod aliquam dolor. | adipiscing. |
| aliquam elit amet. | aliquam. | aliquam. |
| laoreet euismod erat. | dolore elit. | dolor amet. |
|---|---|---|
| lorem. | ut sit. | consectetuer. |
| ipsum sit ut. | ut nibh diam. | dolor amet. |
| aliquam sed. | dolore. | nibh. |
elit euismod euismod amet nibh nibh ipsum sit nibh nibh erat ut. diam dolore adipiscing sed aliquam sed ipsum elit dolor nibh euismod consectetuer. aliquam ut sit ipsum erat erat elit adipiscing nonummy ut aliquam adipiscing. laoreet euismod euismod diam ut sed nibh sed euismod ipsum elit nonummy.
adipiscing adipiscing dolore sed lorem amet. euismod amet euismod amet ut magna. lorem tincidunt consectetuer dolore nibh euismod. ut erat sit tincidunt dolore elit. euismod elit tincidunt magna lorem diam.
amet erat amet erat magna euismod euismod euismod euismod laoreet. nonummy amet euismod dolor dolore dolore tincidunt diam diam laoreet.
amet dolor erat dolore laoreet ut amet erat lorem nonummy erat. diam lorem erat tincidunt aliquam ut lorem ut ipsum dolor diam. amet euismod dolore consectetuer diam laoreet magna adipiscing adipiscing erat tincidunt. amet erat magna aliquam dolore magna aliquam elit dolore nonummy ut.
magna adipiscing erat diam consectetuer sed ipsum tincidunt amet erat laoreet. dolore erat dolore lorem magna dolor dolore tincidunt consectetuer aliquam nonummy. erat sit diam nibh dolore adipiscing nibh nibh lorem consectetuer euismod. amet erat euismod dolore sed euismod erat ut dolore nonummy tincidunt.
dolor nonummy magna euismod sit ut elit dolore elit adipiscing dolore lorem. tincidunt nibh ut dolor euismod erat nonummy amet ut dolore sed lorem. ut sit ut nonummy ipsum lorem adipiscing adipiscing diam tincidunt ut dolore. ut aliquam magna nonummy amet elit euismod consectetuer lorem elit erat elit. erat ut magna tincidunt adipiscing laoreet sit consectetuer dolor dolore aliquam lorem.
ipsum lorem erat elit amet dolor lorem adipiscing sit adipiscing. nonummy elit dolor euismod lorem ut diam sed ut aliquam. lorem magna nonummy sed euismod consectetuer consectetuer nonummy magna aliquam.
sit euismod consectetuer dolore dolore ipsum erat laoreet. nibh dolore tincidunt consectetuer elit amet elit diam.
| Viscosity | Test Method | Temperature |
|---|---|---|
| 200 to 750 cPs | Approx., RVF #2 sp. @ 20 rpm @ 80°F 27°C | 27°C |
| Shear Strength | Type | Cure Time | Cure Temperature | Cure Humidity | Substrate | Test Temperature | Test Method |
|---|---|---|---|---|---|---|---|
| 1,000 psi | Overlap shear strength | 30,240 min | 24°C | 50 % | 1/8 inch birch to 1/8 inch birch. | -37°C | ASTM D 1002, Bonds tested after aging 3 weeks @ 75°F (24°C) and 50% R.H. at a separation rate of 0.2 in./min. |
| 350 psi | Overlap shear strength | 30,240 min | 24°C | 50 % | 1/8 inch birch to 1/8 inch birch. | 24°C | ASTM D 1002, Bonds tested after aging 3 weeks @ 75°F (24°C) and 50% R.H. at a separation rate of 0.2 in./min. |
| 50 psi | Overlap shear strength | 30,240 min | 24°C | 50 % | 1/8 inch birch to 1/8 inch birch. | 82°C | ASTM D 1002, Bonds tested after aging 3 weeks @ 75°F (24°C) and 50% R.H. at a separation rate of 0.2 in./min. |
| 40 psi | Overlap shear strength | 30,240 min | 24°C | 50 % | 1/8 inch birch to 1/8 inch birch. | 93°C | ASTM D 1002, Bonds tested after aging 3 weeks @ 75°F (24°C) and 50% R.H. at a separation rate of 0.2 in./min. |
| 30 psi | Overlap shear strength | 30,240 min | 24°C | 50 % | 1/8 inch birch to 1/8 inch birch | 107°C | ASTM D 1002, Bonds tested after aging 3 weeks @ 75°F (24°C) and 50% R.H. at a separation rate of 0.2 in./min. |
| 55 psi | Overlap shear strength | 1.00 min | 25°C | 50 % | 1/8 inch birch to 1/8 inch birch. | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| 75 psi | Overlap shear strength | 15 min | 25°C | 50 % | 1/8 inch birch to 1/8 inch birch. | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| 130 psi | Overlap shear strength | 30 min | 25°C | 50 % | 1/8 inch birch to 1/8 inch birch. | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| 160 psi | Overlap shear strength | 60 min | 25°C | 50 % | 1/8 inch birch to 1/8 inch birch. | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| 165 psi | Overlap shear strength | 90 min | 25°C | 50 % | 1/8 inch birch to 1/8 inch birch | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| 170 psi | Overlap shear strength | 120 min | 25°C | 50 % | 1/8 inch birch to 1/8 inch birch. | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| 230 psi | Overlap shear strength | 240 min | 25°C | 50 % | 1/8 inch birch to 1/8 inch birch. | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| 260 psi | Overlap shear strength | 480 min | 25°C | 50 % | 1/8 inch birch to 1/8 inch birch. | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| 290 psi | Overlap shear strength | 1,440 min | 25°C | 50 % | 1/8 inch birch to 1/8 inch birch. | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| 320 psi | Overlap shear strength | 4,320 min | 25°C | 50 % | 1/8 inch birch to 1/8 inch birch | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| 350 psi | Overlap shear strength | 10,080 min | 25°C | 50 % | 1/8 inch birch to 1/8 inch birch. | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| 350 psi | Overlap shear strength | 20,160 min | 25°C | 50 % | 1/8 inch birch to 1/8 inch birch. | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| 350 psi | Overlap shear strength | 30,240 min | 25°C | 50 % | 1/8 inch birch to 1/8 inch birch. | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| 55 psi | Overlap shear strength | 1.00 min | 32°C | 90 % | 1/8 inch birch to 1/8 inch birch. | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| 75 psi | Overlap shear strength | 15 min | 32°C | 90 % | 1/8 inch birch to 1/8 inch birch | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| 160 psi | Overlap shear strength | 30 min | 32°C | 90 % | 1/8 inch birch to 1/8 inch birch. | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| 180 psi | Overlap shear strength | 60 min | 32°C | 90 % | 1/8 inch birch to 1/8 inch birch. | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| 190 psi | Overlap shear strength | 90 min | 32°C | 90 % | 1/8 inch birch to 1/8 inch birch. | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| 190 psi | Overlap shear strength | 120 min | 32°C | 90 % | 1/8 inch birch to 1/8 inch birch. | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| 215 psi | Overlap shear strength | 240 min | 32°C | 90 % | 1/8 inch birch to 1/8 inch birch | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| 255 psi | Overlap shear strength | 480 min | 32°C | 90 % | 1/8 inch birch to 1/8 inch birch. | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| 315 psi | Overlap shear strength | 1,440 min | 32°C | 90 % | 1/8 inch birch to 1/8 inch birch. | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| 340 psi | Overlap shear strength | 4,320 min | 32°C | 90 % | 1/8 inch birch to 1/8 inch birch. | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| 350 psi | Overlap shear strength | 10,080 min | 32°C | 90 % | 1/8 inch birch to 1/8 inch birch. | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| 350 psi | Overlap shear strength | 20,160 min | 32°C | 90 % | 1/8 inch birch to 1/8 inch birch | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| 350 psi | Overlap shear strength | 30,240 min | 32°C | 90 % | 1/8 inch birch to 1/8 inch birch | 24°C | ASTM D 1002, 1/8 inch birch to 1/8 inch birch. Adhesive co-spray applied and bonded immediately with nip roll pressure. Bonds aged at 77°F (25°C)/50% R.H. and 90°F (32°C)/90% R.H. for indicated time and then tested at a separation rate of 0.2 in./min. at 75°F (24°C). |
| Tensile Strength | Cure Time | Cure Temperature | Cure Humidity | Test Temperature | Test Method |
|---|---|---|---|---|---|
| 84 psi | 30,240 min | 24°C | 50 % | 24°C | ASTM C 297, Bonds aged for 3 weeks @ 75°F (24°C)/50% R.H. and then tested at a separation rate of 0.05 in./min. |
| 25 psi | 30,240 min | 24°C | 50 % | 82°C | ASTM C 297, Bonds aged for 3 weeks @ 75°F (24°C)/50% R.H. and then tested at a separation rate of 0.05 in./min. |
| 25 psi | 30,240 min | 24°C | 50 % | 93°C | ASTM C 297, Bonds aged for 3 weeks @ 75°F (24°C)/50% R.H. and then tested at a separation rate of 0.05 in./min. |
| 25 psi | 30,240 min | 24°C | 50 % | 107°C | ASTM C 297, Bonds aged for 3 weeks @ 75°F (24°C)/50% R.H. and then tested at a separation rate of 0.05 in./min. |
| % Solids | Test Method |
|---|---|
| High | |
| 47 to 51 % | By weight |
Message sent - We'll get back shortly
Message sent - We'll get back shortly! Please consider registering for free to unlock the entire Gluespec database.
Great! Contact us if you have any additional questions.
You will lose your saved materials unless you register. Please register.
| Manufacturer | Material | Remove |
|---|
Things you can do with checked materials:
| Name | Save Date | View |
|---|
Need help? Our knowledgeable experts help you achieve your goals by giving you application insights. They are available personally to help you before, during or after your search.
