| Application Type | Bond |
|---|---|
| 1 Part or 2 Part | 2 Part |
| Material Form | Liquid |
| Substrate | Aluminum, FRP, PlexiGlass, Metal, Nylon, ABS, Rigid PVC, Rubber, Cold rolled Steel, Wood, Abraded Aluminum, Lexan, Polycarbonate, Primed Steel, Etched Aluminum, Plastic, Steel, Solvent Wiped Aluminum, Polystyrene, Abraded Steel , Plastics, Solvent Wiped Steel, Primed steel |
| Manufacturer | 3M |
| Chemistry | Isocyanate, Polyol, Polyurethane, Urethane |
| Cure Method | Base/Accelerator |
| Cure Temperature (°C) | 20 to 25, 24 |
| Cure Time (min) | 1,440, Fast |
| Viscosity (cPs) | 30,000 |
| Color | Brown |
| Chemical Resistance | Salt spray, Water |
| High Temperature Resistance (°C) | 82 |
| Low Temperature Resistance (°C) | -40 |
| Density (g/cm³) | 10.3 (weight (lbs/gal)), 11.2 (weight (lbs/gal)) |
Surfaces to be bonded must be dry and free from rust, oil, grease and wax. Surfaces can be cleaned with an abrasive such as 3MTM Coated Abrasives (240 grit) followed by wiping with a solvent such as Scotch-GripTM Solvent No. 3.*
*Note: When using solvents, extinguish all ignition sources and follow the manufacturer’s precautions and directions for use when handling such materials.
| nonummy. | nibh. | aliquam. |
|---|---|---|
| nibh adipiscing nonummy. | dolore aliquam. | dolore ipsum. |
| amet euismod. | amet. | tincidunt. |
| tincidunt laoreet. | nonummy euismod. | adipiscing. |
| magna dolor. | dolore aliquam aliquam. | elit adipiscing. |
| diam ipsum aliquam. | euismod erat diam. | dolor. |
| tincidunt dolore euismod diam. | ipsum diam. | ipsum. |
| lorem diam. | ipsum laoreet laoreet. | ut diam. |
|---|---|---|
| erat nonummy dolore. | consectetuer. | aliquam dolore. |
| aliquam nibh elit nibh. | laoreet erat ut. | sit nonummy. |
| amet diam nonummy. | dolor aliquam diam. | euismod. |
|---|---|---|
| ut magna. | elit ut ut. | dolore sit. |
| sit dolore ut. | dolore laoreet dolore. | sed. |
| tincidunt ut. | aliquam laoreet magna. | laoreet erat. |
| dolor nonummy. | ipsum ipsum dolore. | nonummy. |
| nibh elit. | sit nibh. | magna. |
| ipsum laoreet. | ipsum. | ut. |
| amet. | erat. | elit. |
| ipsum nibh. | dolore laoreet euismod. | aliquam magna. |
| erat adipiscing laoreet dolore. | aliquam. | elit. |
|---|---|---|
| consectetuer dolor elit. | ut. | sed amet. |
| dolor. | ipsum consectetuer. | aliquam laoreet. |
| dolor ut magna magna. | ipsum. | tincidunt. |
|---|---|---|
| nonummy. | lorem amet sed. | lorem adipiscing. |
| lorem dolore nibh lorem. | dolore. | amet elit. |
| tincidunt dolore. | ut magna euismod. | elit. |
| dolor dolor aliquam. | erat laoreet amet. | aliquam tincidunt. |
|---|---|---|
| sit. | aliquam elit amet. | ipsum nonummy. |
| amet erat dolor nibh. | dolor ut. | tincidunt euismod. |
| dolore nibh. | euismod amet ut. | dolore. |
| aliquam. | nibh laoreet euismod. | nibh dolore. |
| sed elit ut. | amet amet. | dolore dolor. |
| laoreet magna. | lorem nibh. | lorem. |
| dolore tincidunt. | erat. | magna ut. |
elit dolor dolor sed dolore ipsum erat diam elit lorem nonummy magna. nonummy amet magna erat ipsum sit amet diam adipiscing adipiscing erat elit. ut erat erat laoreet ut euismod ut amet nibh magna adipiscing dolore. lorem euismod dolor lorem adipiscing ipsum nonummy ut nonummy diam lorem diam. lorem nonummy adipiscing adipiscing adipiscing adipiscing euismod lorem sit ut ut dolore.
ut consectetuer adipiscing adipiscing euismod magna ipsum aliquam diam ipsum sit. dolor amet dolore consectetuer magna consectetuer erat diam laoreet amet adipiscing.
aliquam dolor elit laoreet sed sit dolor elit. nibh erat nibh dolore consectetuer dolor sit sed. amet aliquam magna diam magna euismod sed nonummy. sed magna sed dolor elit nibh sed tincidunt. nibh ut amet erat magna lorem dolore tincidunt.
sed sed sed adipiscing ut dolore elit nonummy laoreet lorem lorem. erat nibh aliquam consectetuer nonummy magna sit nibh sit ipsum sit.
euismod magna aliquam ut euismod ipsum nonummy nonummy tincidunt amet. dolor adipiscing aliquam consectetuer lorem tincidunt adipiscing aliquam ipsum nonummy. aliquam amet ut sit euismod magna dolore consectetuer magna tincidunt.
aliquam diam sed magna tincidunt sit amet. aliquam aliquam nonummy nonummy laoreet consectetuer consectetuer. laoreet laoreet sed sit ut dolor ut. consectetuer consectetuer euismod erat erat lorem amet. elit amet dolor amet nonummy laoreet dolor.
magna lorem dolore adipiscing dolore tincidunt ut ut. tincidunt sed tincidunt sit laoreet magna ut sit. erat nibh tincidunt elit consectetuer amet diam dolor. tincidunt consectetuer lorem sit ut tincidunt laoreet adipiscing. diam consectetuer dolor aliquam sit magna nonummy nibh.
| Viscosity | Temperature |
|---|---|
| 30,000 cPs | 24°C |
| Work / Pot Time | Test Method | Temperature |
|---|---|---|
| 5.00 to 15 min | 100 grams mixed at 75°F 24°C: 5-15 min. | 24°C |
| 7 min |
| Tensile Strength | Cure Time | Cure Temperature | Test Temperature | Test Method |
|---|---|---|---|---|
| 3,000 psi | 60 min | 121°C | 20 to 25°C RT | ASTM-D-738 at 2 inches/min. |
| 3,000 psi | 30 min | 141°C | 20 to 25°C RT | ASTM-D-738 at 2 inches/min. |
| Shear Strength | Type | Substrate | Test Time | Test Temperature | Test Method |
|---|---|---|---|---|---|
| 2,500 psi | Overlap shear strength | Etched Aluminum | -40°C | All aluminum data were developed on .063-inch thick 2024 T-3 clad aluminum and all steel data on .035-inch cold rolled steel. Test specimens were 1/2-inch overlap, 1-inch wide with .005-inch thick bondlines pulled at a testing rate of .1-inch/min. | |
| 2,000 psi | Overlap shear strength | Abraded and Solvent Wiped Aluminum | -40°C | All aluminum data were developed on .063-inch thick 2024 T-3 clad aluminum and all steel data on .035-inch cold rolled steel. Test specimens were 1/2-inch overlap, 1-inch wide with .005-inch thick bondlines pulled at a testing rate of .1-inch/min. | |
| 1,000 psi | Overlap shear strength | Solvent Wiped Aluminum | -40°C | All aluminum data were developed on .063-inch thick 2024 T-3 clad aluminum and all steel data on .035-inch cold rolled steel. Test specimens were 1/2-inch overlap, 1-inch wide with .005-inch thick bondlines pulled at a testing rate of .1-inch/min. | |
| 2,000 psi | Overlap shear strength | Abraded and Solvent Wiped Steel | -40°C | All aluminum data were developed on .063-inch thick 2024 T-3 clad aluminum and all steel data on .035-inch cold rolled steel. Test specimens were 1/2-inch overlap, 1-inch wide with .005-inch thick bondlines pulled at a testing rate of .1-inch/min. | |
| 1,000 psi | Overlap shear strength | Solvent Wiped Steel | -40°C | All aluminum data were developed on .063-inch thick 2024 T-3 clad aluminum and all steel data on .035-inch cold rolled steel. Test specimens were 1/2-inch overlap, 1-inch wide with .005-inch thick bondlines pulled at a testing rate of .1-inch/min. | |
| 2,000 psi | Overlap shear strength | Etched Aluminum | 24°C | All aluminum data were developed on .063-inch thick 2024 T-3 clad aluminum and all steel data on .035-inch cold rolled steel. Test specimens were 1/2-inch overlap, 1-inch wide with .005-inch thick bondlines pulled at a testing rate of .1-inch/min. | |
| 2,000 psi | Overlap shear strength | Abraded and Solvent Wiped Aluminum | 24°C | All aluminum data were developed on .063-inch thick 2024 T-3 clad aluminum and all steel data on .035-inch cold rolled steel. Test specimens were 1/2-inch overlap, 1-inch wide with .005-inch thick bondlines pulled at a testing rate of .1-inch/min. | |
| 1,000 psi | Overlap shear strength | Solvent Wiped Aluminum | 24°C | All aluminum data were developed on .063-inch thick 2024 T-3 clad aluminum and all steel data on .035-inch cold rolled steel. Test specimens were 1/2-inch overlap, 1-inch wide with .005-inch thick bondlines pulled at a testing rate of .1-inch/min. | |
| 1,200 psi | Overlap shear strength | Abraded and Solvent Wiped Steel | 24°C | All aluminum data were developed on .063-inch thick 2024 T-3 clad aluminum and all steel data on .035-inch cold rolled steel. Test specimens were 1/2-inch overlap, 1-inch wide with .005-inch thick bondlines pulled at a testing rate of .1-inch/min. | |
| 700 psi | Overlap shear strength | Solvent Wiped Steel | 24°C | All aluminum data were developed on .063-inch thick 2024 T-3 clad aluminum and all steel data on .035-inch cold rolled steel. Test specimens were 1/2-inch overlap, 1-inch wide with .005-inch thick bondlines pulled at a testing rate of .1-inch/min. | |
| 300 psi | Overlap shear strength | Etched Aluminum | 82°C | All aluminum data were developed on .063-inch thick 2024 T-3 clad aluminum and all steel data on .035-inch cold rolled steel. Test specimens were 1/2-inch overlap, 1-inch wide with .005-inch thick bondlines pulled at a testing rate of .1-inch/min. | |
| 300 psi | Overlap shear strength | Abraded and Solvent Wiped Aluminum | 82°C | All aluminum data were developed on .063-inch thick 2024 T-3 clad aluminum and all steel data on .035-inch cold rolled steel. Test specimens were 1/2-inch overlap, 1-inch wide with .005-inch thick bondlines pulled at a testing rate of .1-inch/min. | |
| 100 psi | Overlap shear strength | Solvent Wiped Aluminum | 82°C | All aluminum data were developed on .063-inch thick 2024 T-3 clad aluminum and all steel data on .035-inch cold rolled steel. Test specimens were 1/2-inch overlap, 1-inch wide with .005-inch thick bondlines pulled at a testing rate of .1-inch/min. | |
| 100 psi | Overlap shear strength | Abraded and Solvent Wiped Steel | 82°C | All aluminum data were developed on .063-inch thick 2024 T-3 clad aluminum and all steel data on .035-inch cold rolled steel. Test specimens were 1/2-inch overlap, 1-inch wide with .005-inch thick bondlines pulled at a testing rate of .1-inch/min. | |
| 20 psi | Overlap shear strength | Solvent Wiped Steel | 82°C | All aluminum data were developed on .063-inch thick 2024 T-3 clad aluminum and all steel data on .035-inch cold rolled steel. Test specimens were 1/2-inch overlap, 1-inch wide with .005-inch thick bondlines pulled at a testing rate of .1-inch/min. | |
| 240 psi | Overlap shear strength | Nylon | -40°C | All data were developed on 1/8-inch thick, 1/2-inch overlap, 1-inch wide specimens with .005-inch thick bondlines that had been abraded and alcohol wiped prior to bonding. | |
| 1,240 psi | Overlap shear strength | Lexan | -40°C | Denotes substrate failure., All data were developed on 1/8-inch thick, 1/2-inch overlap, 1-inch wide specimens with .005-inch thick bondlines that had been abraded and alcohol wiped prior to bonding. | |
| 620 psi | Overlap shear strength | Plexiglass | -40°C | All data were developed on 1/8-inch thick, 1/2-inch overlap, 1-inch wide specimens with .005-inch thick bondlines that had been abraded and alcohol wiped prior to bonding. | |
| 1,660 psi | Overlap shear strength | FRP | -40°C | Denotes substrate failure, All data were developed on 1/8-inch thick, 1/2-inch overlap, 1-inch wide specimens with .005-inch thick bondlines that had been abraded and alcohol wiped prior to bonding. | |
| 370 psi | Overlap shear strength | Rigid PVC | -40°C | All data were developed on 1/8-inch thick, 1/2-inch overlap, 1-inch wide specimens with .005-inch thick bondlines that had been abraded and alcohol wiped prior to bonding. | |
| 440 psi | Overlap shear strength | ABS | -40°C | Denotes substrate failure, All data were developed on 1/8-inch thick, 1/2-inch overlap, 1-inch wide specimens with .005-inch thick bondlines that had been abraded and alcohol wiped prior to bonding. | |
| 330 psi | Overlap shear strength | Polystyrene | -40°C | All data were developed on 1/8-inch thick, 1/2-inch overlap, 1-inch wide specimens with .005-inch thick bondlines that had been abraded and alcohol wiped prior to bonding. | |
| 580 psi | Overlap shear strength | Nylon | 24°C | All data were developed on 1/8-inch thick, 1/2-inch overlap, 1-inch wide specimens with .005-inch thick bondlines that had been abraded and alcohol wiped prior to bonding. | |
| 1,840 psi | Overlap shear strength | Lexan | 24°C | Denotes substrate failure., All data were developed on 1/8-inch thick, 1/2-inch overlap, 1-inch wide specimens with .005-inch thick bondlines that had been abraded and alcohol wiped prior to bonding. | |
| 1,300 psi | Overlap shear strength | Plexiglass | 24°C | All data were developed on 1/8-inch thick, 1/2-inch overlap, 1-inch wide specimens with .005-inch thick bondlines that had been abraded and alcohol wiped prior to bonding. | |
| 1,150 psi | Overlap shear strength | FRP | 24°C | Denotes substrate failure., All data were developed on 1/8-inch thick, 1/2-inch overlap, 1-inch wide specimens with .005-inch thick bondlines that had been abraded and alcohol wiped prior to bonding. | |
| 960 psi | Overlap shear strength | Rigid PVC | 24°C | All data were developed on 1/8-inch thick, 1/2-inch overlap, 1-inch wide specimens with .005-inch thick bondlines that had been abraded and alcohol wiped prior to bonding. | |
| 810 psi | Overlap shear strength | ABS | 24°C | All data were developed on 1/8-inch thick, 1/2-inch overlap, 1-inch wide specimens with .005-inch thick bondlines that had been abraded and alcohol wiped prior to bonding. | |
| 530 psi | Overlap shear strength | Polystyrene | 24°C | All data were developed on 1/8-inch thick, 1/2-inch overlap, 1-inch wide specimens with .005-inch thick bondlines that had been abraded and alcohol wiped prior to bonding. | |
| 40 psi | Overlap shear strength | Nylon | 82°C | All data were developed on 1/8-inch thick, 1/2-inch overlap, 1-inch wide specimens with .005-inch thick bondlines that had been abraded and alcohol wiped prior to bonding. | |
| 125 psi | Overlap shear strength | Lexan | 82°C | All data were developed on 1/8-inch thick, 1/2-inch overlap, 1-inch wide specimens with .005-inch thick bondlines that had been abraded and alcohol wiped prior to bonding. | |
| 70 psi | Overlap shear strength | Plexiglass | 82°C | All data were developed on 1/8-inch thick, 1/2-inch overlap, 1-inch wide specimens with .005-inch thick bondlines that had been abraded and alcohol wiped prior to bonding. | |
| 180 psi | Overlap shear strength | FRP | 82°C | All data were developed on 1/8-inch thick, 1/2-inch overlap, 1-inch wide specimens with .005-inch thick bondlines that had been abraded and alcohol wiped prior to bonding. | |
| 110 psi | Overlap shear strength | Rigid PVC | 82°C | All data were developed on 1/8-inch thick, 1/2-inch overlap, 1-inch wide specimens with .005-inch thick bondlines that had been abraded and alcohol wiped prior to bonding. | |
| 300 psi | Overlap shear strength | ABS | 82°C | All data were developed on 1/8-inch thick, 1/2-inch overlap, 1-inch wide specimens with .005-inch thick bondlines that had been abraded and alcohol wiped prior to bonding. | |
| 110 psi | Overlap shear strength | Polystyrene | 82°C | All data were developed on 1/8-inch thick, 1/2-inch overlap, 1-inch wide specimens with .005-inch thick bondlines that had been abraded and alcohol wiped prior to bonding. | |
| 5 psi | Overlap shear strength | plastic to primed steel | 1,800 sec | 25°C | Specimens: 1/2-inch overlap fiber reinforced plastic to primed steel, 0.032-inch bondline. Specimens were pulled at 2 inches/min. |
| 20 psi | Overlap shear strength | plastic to primed steel | 3,600 sec | 25°C | Specimens: 1/2-inch overlap fiber reinforced plastic to primed steel, 0.032-inch bondline. Specimens were pulled at 2 inches/min. |
| 90 psi | Overlap shear strength | plastic to primed steel | 7,200 sec | 25°C | Specimens: 1/2-inch overlap fiber reinforced plastic to primed steel, 0.032-inch bondline. Specimens were pulled at 2 inches/min. |
| 400 psi | Overlap shear strength | plastic to primed steel | 10,800 sec | 25°C | Specimens: 1/2-inch overlap fiber reinforced plastic to primed steel, 0.032-inch bondline. Specimens were pulled at 2 inches/min. |
| 490 psi | Overlap shear strength | plastic to primed steel | 14,400 sec | 25°C | Specimens: 1/2-inch overlap fiber reinforced plastic to primed steel, 0.032-inch bondline. Specimens were pulled at 2 inches/min. |
| 560 psi | Overlap shear strength | plastic to primed steel | 18,000 sec | 25°C | Specimens: 1/2-inch overlap fiber reinforced plastic to primed steel, 0.032-inch bondline. Specimens were pulled at 2 inches/min. |
| 680 psi | Overlap shear strength | plastic to primed steel | 21,600 sec | 25°C | Specimens: 1/2-inch overlap fiber reinforced plastic to primed steel, 0.032-inch bondline. Specimens were pulled at 2 inches/min. |
| 790 psi | Overlap shear strength | plastic to primed steel | 25,200 sec | 25°C | Specimens: 1/2-inch overlap fiber reinforced plastic to primed steel, 0.032-inch bondline. Specimens were pulled at 2 inches/min. |
| 1,200 psi | Overlap shear strength | plastic to primed steel | 57,600 sec | 25°C | Specimens: 1/2-inch overlap fiber reinforced plastic to primed steel, 0.032-inch bondline. Specimens were pulled at 2 inches/min. |
| 1,550 psi | Overlap shear strength | plastic to primed steel | 86,400 sec | 25°C | Specimens: 1/2-inch overlap fiber reinforced plastic to primed steel, 0.032-inch bondline. Specimens were pulled at 2 inches/min. |
| 0 psi | Overlap shear strength | plastic to primed steel | 600 sec | 38°C | Specimens: 1/2-inch overlap shear, fiber reinforced plastic to primed steel .032-inch bondline. Specimens were placed in an oven at designated temperature for the specified time. Bonds were then cooled for 1 minute and pulled at a rate of 2-inch/min. |
| 240 psi | Overlap shear strength | plastic to primed steel | 1,800 sec | 38°C | Specimens: 1/2-inch overlap shear, fiber reinforced plastic to primed steel .032-inch bondline. Specimens were placed in an oven at designated temperature for the specified time. Bonds were then cooled for 1 minute and pulled at a rate of 2-inch/min. |
| 500 psi | Overlap shear strength | plastic to primed steel | 2,700 sec | 38°C | Specimens: 1/2-inch overlap shear, fiber reinforced plastic to primed steel .032-inch bondline. Specimens were placed in an oven at designated temperature for the specified time. Bonds were then cooled for 1 minute and pulled at a rate of 2-inch/min. |
| 650 psi | Overlap shear strength | plastic to primed steel | 3,600 sec | 38°C | Specimens: 1/2-inch overlap shear, fiber reinforced plastic to primed steel .032-inch bondline. Specimens were placed in an oven at designated temperature for the specified time. Bonds were then cooled for 1 minute and pulled at a rate of 2-inch/min. |
| 140 psi | Overlap shear strength | plastic to primed steel | 600 sec | 49°C | Specimens: 1/2-inch overlap shear, fiber reinforced plastic to primed steel .032-inch bondline. Specimens were placed in an oven at designated temperature for the specified time. Bonds were then cooled for 1 minute and pulled at a rate of 2-inch/min. |
| 480 psi | Overlap shear strength | plastic to primed steel | 1,200 sec | 49°C | Specimens: 1/2-inch overlap shear, fiber reinforced plastic to primed steel .032-inch bondline. Specimens were placed in an oven at designated temperature for the specified time. Bonds were then cooled for 1 minute and pulled at a rate of 2-inch/min. |
| 750 psi | Overlap shear strength | plastic to primed steel | 30 sec | 49°C | Specimens: 1/2-inch overlap shear, fiber reinforced plastic to primed steel .032-inch bondline. Specimens were placed in an oven at designated temperature for the specified time. Bonds were then cooled for 1 minute and pulled at a rate of 2-inch/min. |
| 120 psi | Overlap shear strength | plastic to primed steel | 5.00 sec | 66°C | Specimens: 1/2-inch overlap shear, fiber reinforced plastic to primed steel .032-inch bondline. Specimens were placed in an oven at designated temperature for the specified time. Bonds were then cooled for 1 minute and pulled at a rate of 2-inch/min. |
| 400 psi | Overlap shear strength | plastic to primed steel | 10 sec | 66°C | Specimens: 1/2-inch overlap shear, fiber reinforced plastic to primed steel .032-inch bondline. Specimens were placed in an oven at designated temperature for the specified time. Bonds were then cooled for 1 minute and pulled at a rate of 2-inch/min. |
| 760 psi | Overlap shear strength | plastic to primed steel | 15 sec | 66°C | Specimens: 1/2-inch overlap shear, fiber reinforced plastic to primed steel .032-inch bondline. Specimens were placed in an oven at designated temperature for the specified time. Bonds were then cooled for 1 minute and pulled at a rate of 2-inch/min. |
| 400 psi | Overlap shear strength | plastic to primed steel | 5.00 sec | 82°C | Specimens: 1/2-inch overlap shear, fiber reinforced plastic to primed steel .032-inch bondline. Specimens were placed in an oven at designated temperature for the specified time. Bonds were then cooled for 1 minute and pulled at a rate of 2-inch/min. |
| 660 psi | Overlap shear strength | plastic to primed steel | 10 sec | 82°C | Specimens: 1/2-inch overlap shear, fiber reinforced plastic to primed steel .032-inch bondline. Specimens were placed in an oven at designated temperature for the specified time. Bonds were then cooled for 1 minute and pulled at a rate of 2-inch/min. |
| 900 psi | Overlap shear strength | plastic to primed steel | 15 sec | 82°C | Specimens: 1/2-inch overlap shear, fiber reinforced plastic to primed steel .032-inch bondline. Specimens were placed in an oven at designated temperature for the specified time. Bonds were then cooled for 1 minute and pulled at a rate of 2-inch/min. |
| 340 psi | Overlap shear strength | plastic to primed steel | 2.00 sec | 93°C | Specimens: 1/2-inch overlap shear, fiber reinforced plastic to primed steel .032-inch bondline. Specimens were placed in an oven at designated temperature for the specified time. Bonds were then cooled for 1 minute and pulled at a rate of 2-inch/min. |
| 660 psi | Overlap shear strength | plastic to primed steel | 5.00 sec | 93°C | Specimens: 1/2-inch overlap shear, fiber reinforced plastic to primed steel .032-inch bondline. Specimens were placed in an oven at designated temperature for the specified time. Bonds were then cooled for 1 minute and pulled at a rate of 2-inch/min. |
| 900 psi | Overlap shear strength | plastic to primed steel | 10 sec | 93°C | Specimens: 1/2-inch overlap shear, fiber reinforced plastic to primed steel .032-inch bondline. Specimens were placed in an oven at designated temperature for the specified time. Bonds were then cooled for 1 minute and pulled at a rate of 2-inch/min. |
| 440 psi | Overlap shear strength | plastic to primed steel | 2.00 sec | 107°C | Specimens: 1/2-inch overlap shear, fiber reinforced plastic to primed steel .032-inch bondline. Specimens were placed in an oven at designated temperature for the specified time. Bonds were then cooled for 1 minute and pulled at a rate of 2-inch/min. |
| 760 psi | Overlap shear strength | plastic to primed steel | 5.00 sec | 107°C | Specimens: 1/2-inch overlap shear, fiber reinforced plastic to primed steel .032-inch bondline. Specimens were placed in an oven at designated temperature for the specified time. Bonds were then cooled for 1 minute and pulled at a rate of 2-inch/min. |
| 900 psi | Overlap shear strength | plastic to primed steel | 10 sec | 107°C | Specimens: 1/2-inch overlap shear, fiber reinforced plastic to primed steel .032-inch bondline. Specimens were placed in an oven at designated temperature for the specified time. Bonds were then cooled for 1 minute and pulled at a rate of 2-inch/min. |
Message sent - We'll get back shortly
Message sent - We'll get back shortly! Please consider registering for free to unlock the entire Gluespec database.
Great! Contact us if you have any additional questions.
You will lose your saved materials unless you register. Please register.
| Manufacturer | Material | Remove |
|---|
Things you can do with checked materials:
| Name | Save Date | View |
|---|
Need help? Our knowledgeable experts help you achieve your goals by giving you application insights. They are available personally to help you before, during or after your search.
