Application Type Bond, Hold, Mount 1 Part or 2 Part 1 Part Material Form Foam Tape Manufacturer 3M Chemistry Polyurethane, Acrylic, Polyurethane Foam Cure Method Pressure Sensitive Color Natural, Off-White Relative Solvent Resistance Chemical Resistance: Hydrocarbon solvent High Temperature Resistance (°C) 104, 193, High Density (g/cm³) 0.190 Key Specifications TSCA
Technical Data for 3M 4004
- Adhesive - Bond, Hold, Mount
1 Part or 2 Part
- 1 Part or 2 Part - 1 Part
- Tape - Foam Tape
- Flow - Flow equipment
- Pressure Sensitive (min) - Pressure Sensitive
- Other - Natural
- TSCA (Toxic Substances Control Act) - TSCA
Application Temperature (°F) 70 to 100
Shear Strength (psi) High, 1000 (gms), 500 (gms), 500 (gms), 250 (gms) Test Method Tensile Strength (psi) 12, 90 Test Method
UV Resistance UV resistance High Temperature Resistance (°C) 104, 193, High
Dielectric Strength (V/mil) 200 to 300 Thermal Conductivity (W/m°K) 0.06
Elongation (%) 90 Flexibility Firm
Density (g/cm³) 0.190
Shelf Life Details Store in original cartons at 70°F (21°C) and 50% relative humidity.;To obtain best performance, use these products within 24 months from date of manufacture except 3M™ Double Coated Urethane Foam Tape 4085 which is 18 months from date of manufacture. Shelf Life Temperature (°F) 70 Shelf Life Type from date of manufacture Shelf Life (mon) 18
Best Practices for 3M 4004
To obtain optimum adhesion, the bonding surfaces must be clean, dry and well unified. Typical surface cleaning solvents are isopropyl alcohol* and water (rubbing alcohol) or heptane.*Note: Be sure to follow the manufacturer’s precautions and directions for use when using solvents.
Bond strength is dependent upon the amount of adhesive-to-surface contact developed. Firm application pressure helps develop better adhesive contact and improve bond strength.
Ideal tape application temperature range is 70°F to 100°F (21°C to 38°C). Initial tape application to surfaces at temperatures below 50°F (10°C) is not recommended because the adhesive becomes too firm to adhere readily. However, once properly applied, low temperature holding is generally satisfactory.
Comparable Materials for 3M 4004
Spec Engine® Results
Questions about this material?
Get personal assistance with your specific application needs.
Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of MaterialsRead Article
Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:Read Article
Shear Strength Test Methods
|Shear Strength||Type||Test Time||Test Temperature||Test Method|
|1000 (gms)||Static shear strength||360,000 sec||22°C||Measured at various temperatures and gram loadings. (1/2 sq. in. overlap).Will hold listed weight for 100 hours.|
|500 (gms)||Static shear strength||360,000 sec||49°C||Measured at various temperatures and gram loadings. (1/2 sq. in. overlap).Will hold listed weight for 100 hours.|
|500 (gms)||Static shear strength||360,000 sec||66°C||Measured at various temperatures and gram loadings. (1/2 sq. in. overlap).Will hold listed weight for 100 hours.|
|250 (gms)||Static shear strength||360,000 sec||93°C|
Tensile Strength Test Methods
|Tensile Strength||Test Method|
|12 psi||(“T” Block) 1 in2 (6.45 cm2) Jaw Speed 2 in/min (50 mm/min)|