Application Type Bond 1 Part or 2 Part 1 Part Material Form Foam Tape Substrate acrylic, Aluminum, glass, ABS, PVC (non-plasticized), Enameled steel, Stainless Steel, latex-painted wood, lacquered wood Industry Absorb vibration in printers, Keyboards, Computers, Door, Windows, Cabinet seals, Aircraft lights, Automotive dash boards, Recessed lighting, Aerospace Manufacturer 3M Chemistry Acrylic, Urethane Cure Method Pressure Sensitive Color Charcoal grey Aging Resistance Excellent aging resistance Chemical Resistance Gasoline, JP-4 (jet fuel), MEK, Mineral Spirits High Temperature Resistance (°C) 66, 121 Low Temperature Resistance (°C) -29 Density (g/cm³) Low, 0.032
Technical Data for 3M 4317
- Adhesive - Bond
1 Part or 2 Part
- 1 Part or 2 Part - 1 Part
- Tape - Foam Tape
- Pressure Sensitive (min) - Pressure Sensitive
- Gray - Charcoal grey
Application Temperature (°F) 70 to 100
Tensile Strength (psi) 25 Test Method
Aging Resistance Excellent aging resistance Chemical Resistance Gasoline, JP-4 (jet fuel), MEK, Mineral Spirits UV Resistance Excellent High Temperature Resistance (°C) 66, 121 Low Temperature Resistance (°C) -29
Dielectric Strength (V/mil) 40 Test Method Thermal Conductivity (W/m°K) 0.04 Test Method Surface Resistivity (O) 3e12 (ohms/sq), 5e12 (ohms/sq) Test Method
Elongation (%) 125 Test Method Shore OO Hardness 6 Test Method
Density (g/cm³) Low, 0.032 Test Method
Shelf Life Details Storage: Store in the original cartons at 60-80°F (15-27°C) and 50% relative humidity. Shelf Life Temperature (°F) 140 to 176 Shelf Life Type From date of manufacture Shelf Life (mon) 18
Best Practices for 3M 4317
To obtain optimum adhesion, the bonding surface must be clean, dry, and well unified. Some typical surface cleaning solvents are isopropyl alcohol and heptane.
Be sure to follow the solvent manufacturer’s precautions and directions for use when handling solvents.
Bond strength is dependent upon the amount of adhesive-to-surface contact. Firm application pressure develops better adhesive contact and helps improve bond strength.
Initial tape application to surfaces at temperatures below 50°F (10°C) is not recommended because the adhesive becomes too firm to adhere readily. However, once properly applied, low temperature holding is generally satisfactory.
Comparable Materials for 3M 4317
Spec Engine® Results
Questions about this material?
Get personal assistance with your specific application needs.
Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of MaterialsRead Article
Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:Read Article
Tensile Strength Test Methods
|Tensile Strength||Test Method|
|25 psi||ASTM D-3574, Die "A"|
Dielectric Strength Test Methods
|Dielectric Strength||Test Method|
|40 V/mil||ASTM D-149|
Surface Resistivity Test Methods
|Surface Resistivity||Test Method|
|3e12 (ohms/sq)||Non-adhesive side, ASTM D-257|
|5e12 (ohms/sq)||Adhesive side, ASTM D-257|
Thermal Conductivity Test Methods
|Thermal Conductivity||Test Method|
|0.04 W/m°K||ASTM C-518|
Elongation Test Methods
|125 %||ASTM D-3574, Die “A”|
Shore OO Hardness Test Methods
|Shore OO Hardness||Shore Hardness Test Method|
|6||ASTM D-2240, Foam with adhesive|
Density Test Methods
|0.032 g/cm³||ASTM D-3574, Foam with adhesive|