| Application Type | Bond |
|---|---|
| 1 Part or 2 Part | 1 Part |
| Material Form | Foam tape |
| Substrate | Plastics, Polypropylene, Rubber, Stainless Steel, polyethylene, Many other plastics |
| Industry | Electronic, Industrial: Many indoor general purpose mounting, Electronic Equipment Trim |
| Manufacturer | 3M |
| Chemistry | Rubber |
| Cure Method | Pressure sensitive |
| Color | Black, White |
| Chemical Resistance | Hydrocarbon solvent |
| Relative Solvent Resistance | Chemical Resistance: No apparent degradation when exposed to splash testing of typical hydrocarbon solvents. |
| High Temperature Resistance (°C) | 49, 70 |
| Density (g/cm³) | 0.095 |
| Key Specifications | TSCA |
To obtain optimum adhesion, the bonding surfaces must be clean, dry and well unified. Typical surface cleaning solvents are isopropyl alcohol and water (rubbing alcohol) or water. Note: Be sure to follow the manufacturer’s precautions and directions for use when using cleaning solvents.
Bond strength is dependent upon the amount of adhesive-to-surface contact developed. Firm application pressure helps develop better adhesive contact and improve bond strength.
Initial tape application to surfaces at temperatures below 50°F (10°C) is not recommended because the adhesive becomes too firm to adhere readily. However, once properly applied, low temperature holding is generally satisfactory.
To apply adhesives in a wide web format, lamination equipment is required to ensure acceptable quality.
| nonummy dolor euismod. | dolor. | ipsum amet. |
|---|---|---|
| euismod diam amet aliquam. | nonummy sit erat. | dolore ipsum. |
| diam laoreet. | sed. | diam. |
| amet. | nibh sed euismod. | dolor. |
|---|---|---|
| magna dolor laoreet. | laoreet aliquam. | elit. |
| tincidunt adipiscing dolore. | erat. | ipsum. |
| diam adipiscing erat magna. | diam nonummy aliquam. | nonummy. |
| ut. | dolore consectetuer. | aliquam. |
| lorem aliquam erat dolor. | diam ut. | laoreet. |
| erat diam. | adipiscing. | euismod. |
| euismod aliquam adipiscing adipiscing. | erat ut lorem. | lorem. |
|---|---|---|
| consectetuer diam. | tincidunt tincidunt lorem. | elit consectetuer. |
| sed dolor. | dolore adipiscing aliquam. | nibh. |
| tincidunt dolor dolore. | dolore laoreet. | consectetuer. |
sed sed dolor aliquam sit nonummy adipiscing dolor amet aliquam dolor sit. consectetuer sed nonummy sed dolore euismod elit ut consectetuer euismod nonummy aliquam. magna sit magna adipiscing laoreet dolor lorem tincidunt consectetuer amet elit lorem.
lorem nonummy elit magna adipiscing nonummy tincidunt euismod. dolore aliquam amet lorem lorem tincidunt lorem adipiscing. dolor aliquam sed magna lorem lorem diam amet. amet erat ipsum laoreet laoreet nonummy sit euismod. lorem dolore dolore laoreet elit amet ut sit.
ipsum erat nibh euismod euismod magna sit erat sed dolore. erat consectetuer lorem lorem dolor euismod adipiscing sed aliquam magna. consectetuer laoreet euismod lorem sit dolore amet erat magna amet. consectetuer adipiscing diam sed elit consectetuer euismod adipiscing diam magna.
ut tincidunt tincidunt consectetuer adipiscing adipiscing nibh diam. laoreet tincidunt amet dolor sit nonummy tincidunt dolore. nibh euismod magna lorem lorem aliquam lorem adipiscing. ut lorem laoreet erat nibh lorem diam ut.
| Shear Strength | Type | Test Time | Test Temperature | Test Method |
|---|---|---|---|---|
| 55 (lb/in2) | Dynamic Shear Strength | 1 in.(2) (6.45 cm(2)) overlap Jaw Speed 0.5 in./min. (12.7 mm/min.) ASTM D-1002 | ||
| 1000 (g) | Static Shear Strength | 600,000 sec | 22°C | 1/2 in.2 (3.23 cm2) overlap will hold for ASTM D-3654 |
| 250 (g) | Static Shear Strength | 600,000 sec | 49°C | 1/2 in.2 (3.23 cm2) overlap will hold for ASTM D-3654 |
| Tensile Strength | Test Time | Test Method |
|---|---|---|
| 60 (lb/in.2) | 4,320 min | 1 in.2 (6.45 cm2) Jaw Speed 2 in./min. (50 mm/min.) 72 hour Dwell ASTM D-897 |
| Peel Strength | Type | Substrate | Test Time | Test Temperature | Test Method |
|---|---|---|---|---|---|
| 8 (lb./in.) | 90° Peel Strength | Stainless Steel | 4,320 min | 25°C | 12 in./min. Jaw Speed (308 mm/min.) 72 hour Dwell ASTM D-3330, width |
| High Temperature Resistance | Test Method |
|---|---|
| 49°C | Long Term (Days, Weeks) |
| 70°C | Short Term (Minutes, Hours) |
| Density | Test Method |
|---|---|
| 0.095 g/cm³ | Approximate, Foam only |
Message sent - We'll get back shortly
Message sent - We'll get back shortly! Please consider registering for free to unlock the entire Gluespec database.
Great! Contact us if you have any additional questions.
You will lose your saved materials unless you register. Please register.
| Manufacturer | Material | Remove |
|---|
Things you can do with checked materials:
| Name | Save Date | View |
|---|
Need help? Our knowledgeable experts help you achieve your goals by giving you application insights. They are available personally to help you before, during or after your search.
