

-
Description for 3M 4947F (Black version of 4941)
• Gray, closed-cell acrylic foam carrier • Conformable • Good adhesion to many painted metals • Plasticizer resistant • UL 746CChemical Resistance Chemical Resistance: Excellent solvent resistance, Chemical Resistance: Resistance to plasticizer migration Application Type Bond 1 Part or 2 Part 1-Part Material Form Tape Substrate Acrylic paint, Aluminum, Ceramic, Glass, Metal, A wide variety of plastics, Polycarbonate, Polyester paint, Polyurethane paint, PVC, Enameled Steel, Stainless steel, Nickel Coated ABS, Plasticized Vinyl, Galvanized Steel, Epoxy, Galvanized Steel, PBT, Foam, ABS, Painted Metals, Nickel Coated ABS Industry Ideal for use in many interior bonding applications, Ideal for use in many exterior bonding applications, Rivets Manufacturer 3M Chemistry Acrylic Cure Method Pressure sensitive Application Temperature (°F) 70 to 100, 59 Color Black High Temperature Resistance (°C) 110, 93, 149, 75, 90, Outstanding durability Low Temperature Resistance (°C) -35, Outstanding durability Other Resistance Fuel resistance Volume Resistivity (O) 2.1e14 (ohm-cm) Density (g/cm³) 0.720 Key Specifications UL 746C -
Technical Data for 3M 4947F (Black version of 4941)
Overview
-
Chemical Resistance
- Chemical Resistance : Relative Solvent Resistance - Excellent solvent resistance
- Chemical Resistance : Plasticizer Resistance - Resistance to plasticizer migration
-
Application Type
- Adhesive - Bond
-
1 Part or 2 Part
- 1-Part
-
Material Form
- Tape
-
Substrate
- Ceramic
- Foam
- Glass
- Metal - Painted Metals
- Aluminum
- Steel - Enameled Steel
- Nickel - Nickel Coated ABS
- Galvanized - Galvanized Steel
- Plastic - A wide variety of plastics
- Acrylic (PMMA) - Acrylic paint
- Polycarbonate
- Polyurethane - Polyurethane paint
- Polyvinyl chloride (PVC) - PVC
- Vinyl - Plasticized Vinyl
- Epoxy
- ABS - Nickel Coated ABS
- Polyester - Polyester paint
- Polybutylene Terephthalate (PBT) - PBT
- Stainless Steel
- Galvanized Steel
- Other - Paint, High and medium surface energy substrates
-
Industry
- Rivet - Rivets
- Interior - Ideal for use in many interior bonding applications
- Industrial - Other permanent fasteners, Foils, Spot Welds
- Industrial Exterior - Ideal for use in many exterior bonding applications
- Construction
-
Chemistry
-
Application Method
- Dispenser - P.U.R. application equipment
-
Cure Method
- Pressure Sensitive (min) - Pressure sensitive
-
Color
- Black
-
Key Specifications
- UL (Underwriters Laboratory), ULC (Underwriters Laboratories of Canada), NFPA (National Fire Protection Association) - UL 746C
Specifications
Cure Specs
Application Temperature (°F) 70 to 100, 59 Bond Strength
General Bond Strength (psi) Good Peel Strength (piw) High, 22 (lb/in) Test Method Shear Strength (psi) High, 70, 1000 (grams), 500 (grams), 500 (grams) Test Method Tensile Strength (psi) High, 85 Test Method Material Resistance
High Temperature Resistance (°C) 110, 93, 149, 75, 90, Outstanding durability Test Method Low Temperature Resistance (°C) -35, Outstanding durability Moisture/Humidity Resistance Excellent Other Resistance Fuel resistance Conductivity
Dissipation Factor 0.02450, 0.03740 Test Method Dielectric Strength (V/mil) 360 Test Method Dielectric Constant 2.29, 1.99 Test Method Thermal Conductivity (W/m°K) 0.08 Surface Resistivity (O) 2.7e14 (ohm/sq) Test Method Volume Resistivity (O) 2.1e14 (ohm-cm) Test Method Hardness
Flexibility Conformability Modulus (psi) 3e5 (Pa) Test Method Other Properties
Coefficient of Thermal Expansion (CTE) 100e-6 (in./ in/°F) Density (g/cm³) 0.720 Business Information
Shelf Life Details All 3M™ VHB™ Tapes have a shelf life of 24 months from date of shipment when stored at 40°F to 100°F (4°C to 38°C) and 0-95% relative humidity. The optimum storage conditions are 72°F (22°C) and 50% relative humidity.lPerformance of tapes is not projected to change even after shelf life expires; however, 3M does suggest that 3M™ VHB™ Tapes are used prior to the shelf life date whenever possible. Shelf Life Temperature (°F) 40 to 100 Shelf Life Type From date of shipment Shelf Life (mon) 24 -
-
Best Practices for 3M 4947F (Black version of 4941)
-
Surface Preparation
Most substrates are best prepared by cleaning with a 50:50 mixture of isopropyl alcohol (IPA*) and water prior to applying 3M™ VHB™ Tapes.
Exceptions to the general procedure that may require additional surface preparation include: Heavy Oils: A degreaser or solvent-based cleaner may be required to remove heavy oil or grease from a surface and should be followed by cleaning with IPA/water.
Abrasion: Abrading a surface, followed by cleaning with IPA/water, can remove heavy dirt or oxidation and can increase surface area to improve adhesion.
Adhesion Promoters: Priming a surface can significantly improve initial and ultimate adhesion to many materials such as plastics and paints.
Porous surfaces: Most porous and fibered materials such as wood, particleboard, concrete, etc. need to be sealed to provide a unified surface.
Unique Materials: Special surface preparation may be needed for glass and glass-like materials, copper and copper containing metals, and plastics or rubber that contain components that migrate (e.g. plasticizers).
Refer to 3M Technical Bulletin “Surface Preparation for 3M™ VHB™ Tape Applications” for additional details and suggestions. (70-0704-8701-5)
*Note: These cleaner solutions contain greater than 250 g/l of volatile organic compounds (VOC). Please consult your local Air Quality Regulations to be sure the cleaner is compliant. When using solvents, be sure to follow the manufacturer’s precautions and directions for use when handling such materials.
-
Application
Bond strength is dependent upon the amount of adhesive-to-surface contact developed. Firm application pressure develops better adhesive contact and helps improve bond strength. Typically, good surface contact can be attained by applying enough pressure to insure that the tape experiences approximately 15 psi (100 kPa) pressure. Either roller or platen pressure can be used. Note that rigid surfaces may require 2 or 3 times that much pressure to make the tape experience 15 psi.
Ideal application temperature range is 70°F to 100°F (21°C to 38°C). Pressure sensitive adhesives use viscous flow to achieve substrate contact area. Minimum suggested application temperatures:60°F (15°C): 3M™ VHB™ Tapes 4941, 4945 families.
Note: Initial tape application to surfaces at temperatures below these suggested minimums is not recommended because the adhesive becomes too firm to adhere readily. However, once properly applied, low temperature holding is generally satisfactory.
-
Curing
After application, the bond strength will increase as the adhesive flows onto the surface (also referred to as “wet out”). At room temperature approximately 50% of ultimate bond strength will be achieved after 20 minutes, 90% after 24 hours and 100% after 72 hours. This flow is faster at higher temperatures and slower at lower temperatures. Ultimate bond strength can be achieved more quickly (and in some cases bond strength can be increased) by exposure of the bond to elevated temperatures (e.g. 150°F [66°C] for 1 hour). This can provide better adhesive wetout onto the substrates. Abrasion of the surfaces or the use of primers/ adhesion promoters can also have the effect of increasing bond strength and achieving ultimate bond strength more quickly.
-
-
Comparable Materials for 3M 4947F (Black version of 4941)
Spec Engine® Results
Popular Articles
Testing the effectiveness of surface treatments
Read ArticleWhat Projects Require Custom Adhesive Formulations and Why?
Read ArticleInfographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation
Read ArticlePlastic Bonding with Adhesives - Considerations Q&A
Read ArticleSponsored Articles
Unique Advantages of Contact Adhesives
Read ArticleUsing LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials
Read ArticleSylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:
Read ArticleCase Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive
Read ArticleFeatured Ads

Peel Strength Test Methods
Peel Strength | Type | Cure Time | Substrate | Test Temperature | Test Method |
---|---|---|---|---|---|
High | |||||
22 (lb/in) | 90° Peel strength | 4,320 min | Stainless steel | 25°C | Based on ASTM D3330 -To stainless steel, room temperature, jaw speed 12 in/min (305 mm/min). Average force to remove is measured. 72 hour dwell. |
Tensile Strength Test Methods
Tensile Strength | Type | Cure Time | Substrate | Test Temperature | Test Method |
---|---|---|---|---|---|
High | |||||
85 psi | T-Block Tensile | 4,320 min | Aluminum | 25°C | ASTM D-897 - To aluminum, room temperature, 1 in2 (6.45 cm2), jaw speed 2 in/min (50 mm/min.) Peak force to separate is measured. 72 hour dwell. |
Shear Strength Test Methods
Shear Strength | Type | Cure Time | Substrate | Test Time | Test Temperature | Test Method |
---|---|---|---|---|---|---|
High | ||||||
70 psi | Dynamic overlap shear strength | 4,320 min | Stainless steel | 25°C | ASTM D-1002 - To stainless steel, room temperature, 1 in2 (6.45 cm2), jaw speed 0.5 in/min (12.7 mm/min.) Peak force to separate is measured. 72 hour dwell. | |
1000 (grams) | Static shear strength | Stainless steel | 604,800 sec | 22°C | ASTM D3654 - To stainless steel, tested at various temperatures and gram loadings. 0.5 in2 (3.22 cm2). Will hold listed weight for 10,000 minutes (approximately 7 days). Conversion: 1500 g/0.5 in2 equals 6.6 lb/in2, 500 g/0.5 in2 = 2.2 lb/in2. | |
500 (grams) | Static shear strength | Stainless steel | 604,800 sec | 66°C | ASTM D3654 - To stainless steel, tested at various temperatures and gram loadings. 0.5 in2 (3.22 cm2). Will hold listed weight for 10,000 minutes (approximately 7 days). Conversion: 1500 g/0.5 in2 equals 6.6 lb/in2, 500 g/0.5 in2 = 2.2 lb/in2. | |
500 (grams) | Static shear strength | Stainless steel | 604,800 sec | 93°C | ASTM D3654 - To stainless steel, tested at various temperatures and gram loadings. 0.5 in2 (3.22 cm2). Will hold listed weight for 10,000 minutes (approximately 7 days). Conversion: 1500 g/0.5 in2 equals 6.6 lb/in2, 500 g/0.5 in2 = 2.2 lb/in2. |
High Temperature Resistance Test Methods
High Temperature Resistance | Test Method |
---|---|
110°C | |
93°C | Long Term Temperature Tolerance - Maximum temperature where tape supports at least 250 g load per 0.5 in2 in static shear for 10,000 minutes. (Represents continuous exposure for days or weeks). |
149°C | Short Term Temperature Tolerance - No change in room temperature dynamic shear properties following 4 hours conditioning at indicated temperature with 100 g/static load. (Represents minutes, hours in a process type temperature exposure). |
75°C | |
90°C | |
Outstanding durability |
Dielectric Constant Test Methods
Dielectric Constant | Test Method |
---|---|
2.29 | At 1 kHz, ASTM D150 |
1.99 | At 1MHz, ASTM D150 |
Dielectric Strength Test Methods
Dielectric Strength | Test Method |
---|---|
360 V/mil | ASTM D140 |
Dissipation Factor Test Methods
Dissipation Factor | Test Method |
---|---|
0.02450 | At1 kHz, ASTM D150 |
0.03740 | At 1MHz, ASTM D150 |
Surface Resistivity Test Methods
Surface Resistivity | Test Method |
---|---|
2.7e14 (ohm/sq) | ASTM D257 |
Volume Resistivity Test Methods
Volume Resistivity | Test Method |
---|---|
2.1e14 (ohm-cm) | ASTM D257 |
Modulus Test Methods
Modulus | Temperature | Test Method |
---|---|---|
3e5 (Pa) | 25°C | Shear strength, 1 Hz |