| Application Type | Bond, Seal |
|---|---|
| 1 Part or 2 Part | 1 Part |
| Material Form | Medium Paste |
| Substrate | Aluminum, Copper, Metal: Brass, Metal: Bronze, Lead, Zinc (Galvanized), Fiberglass, Glass, Nylon, gelcoat, Polycarbonate, Polypropylene, Steel, Stainless Steel, Wood, Acrylic, Metal, Plastics/Polymers, Teak, Primed metal, ABS, Pine, Oak, Maple, Fir, Mahogany |
| Industry | Transportation: Marine industry |
| Manufacturer | 3M |
| Chemistry | Polyurethane |
| Cure Method | Moisture |
| Cure Temperature (°C) | 21, 21 |
| Cure Time (min) | 1,440, Fast, 7,200 |
| Viscosity (cPs) | Medium Paste Consistency |
| Color | White |
| High Temperature Resistance (°C) | 88 |
| Low Temperature Resistance (°C) | -40 |
| Density (g/cm³) | 11.0 (Lbs/Gallon) (Approx.) |
There are waxes, coatings, sealants, grease, oil and other contaminants used in the marine industry, making it very important to clean all surfaces to be bonded before applying 3MTM Marine Adhesive/ Sealant Fast Cure 5200. Recommended procedures include cleaning with 3MTM General Purpose Adhesive Cleaner, P. N. 08984.
Alcohol should not be used in preparation for bonding as it will stop the curing process.
Abrading the surfaces with a 180 grit to 220 grit abrasive will enhance the bond strength. Cut tip to desired bead size, puncture seal in nozzle and remove the seal at bottom end of cartridge. Place cartridge in a caulk gun. Apply Fast Cure 5200 to the seam or part to be bonded. Position parts. Tool material to desired appearance. Remove excess with 3MTM General Purpose Adhesive Cleaner*, P. N. 08984.
For cleaning Fast Cure 5200 before it is cured, use a dry cloth to remove the majority of sealant, followed by a cloth damp with General Purpose Adhesive Cleaner*, P. N. 08984, toluene or acetone. Cured Fast Cure 5200 can be removed mechanically with a knife, razor blade or sanding.
Cured Fast Cure 5200 can be removed mechanically with a knife, razor blade, or sanding.
| ut dolor nibh euismod. | ipsum erat magna. | sed sed. |
|---|---|---|
| lorem. | ut elit nibh. | sed. |
| euismod nonummy sit diam. | consectetuer elit. | nibh. |
| dolor consectetuer aliquam. | ut. | ipsum. |
| tincidunt euismod. | lorem consectetuer aliquam. | ut dolore. |
| dolore sed magna. | sed. | dolore. |
| elit. | tincidunt. | elit sit. |
| dolore. | aliquam ipsum. | nonummy aliquam. |
| tincidunt. | aliquam. | nonummy ut. |
| lorem dolor aliquam. | dolore magna consectetuer. | euismod ipsum. |
|---|---|---|
| nibh laoreet. | adipiscing elit. | ut. |
| amet euismod. | nibh nonummy aliquam. | euismod. |
| magna tincidunt tincidunt erat. | lorem ut. | diam magna. |
| sed. | laoreet. | magna tincidunt. |
| ipsum magna ipsum. | dolor adipiscing. | lorem. |
|---|---|---|
| amet elit. | nibh. | sit euismod. |
| magna adipiscing amet aliquam. | elit. | tincidunt dolore. |
| tincidunt dolor erat adipiscing. | diam magna sit. | consectetuer. |
| diam amet ut dolore. | lorem magna. | sed. |
| sit nonummy diam tincidunt. | nonummy laoreet. | ut. |
| aliquam nibh consectetuer nibh. | lorem consectetuer sed. | aliquam ut. |
|---|---|---|
| dolor. | lorem. | euismod. |
| laoreet elit. | erat. | ut. |
| euismod ipsum consectetuer. | ut diam nonummy. | magna nonummy. |
| erat. | tincidunt ipsum euismod. | nonummy ipsum. |
| tincidunt nonummy. | amet adipiscing nonummy. | dolor. |
| diam adipiscing. | aliquam dolore ut. | adipiscing tincidunt. |
| dolore dolore. | ipsum. | tincidunt ipsum. |
| aliquam ipsum. | sit. | elit dolore. |
sed consectetuer aliquam consectetuer ipsum elit tincidunt euismod ut lorem. magna ut erat nonummy dolor nibh dolore elit euismod ipsum. laoreet euismod sit adipiscing sit diam euismod sed dolore magna.
ipsum lorem euismod dolor amet amet aliquam diam erat diam tincidunt. diam dolor magna aliquam dolor nonummy ipsum consectetuer aliquam adipiscing magna. laoreet dolor euismod dolor nibh ut consectetuer laoreet magna lorem elit.
nonummy dolore lorem euismod ut adipiscing adipiscing. laoreet laoreet nibh sed sit amet nonummy. diam dolor euismod amet amet sit euismod. euismod dolor dolor erat elit euismod ipsum. diam ipsum amet ut ipsum nibh euismod.
lorem aliquam diam ipsum amet dolore nibh ut adipiscing erat aliquam diam. nibh nonummy elit euismod nibh magna tincidunt aliquam tincidunt adipiscing tincidunt amet.
sit consectetuer ut nonummy sed adipiscing nonummy amet ipsum tincidunt. dolor erat nonummy ut adipiscing sed lorem laoreet dolor sit.
amet laoreet nonummy diam aliquam euismod tincidunt. ipsum consectetuer diam magna adipiscing dolor aliquam. ipsum sed elit elit sed consectetuer lorem. ipsum elit sit euismod adipiscing tincidunt euismod.
elit nibh magna nonummy euismod sed amet nonummy aliquam adipiscing. ut laoreet magna elit amet dolor sed adipiscing magna nibh. erat ipsum erat ut nibh nonummy laoreet dolor elit adipiscing. nonummy nibh ut laoreet magna sed sit dolore nonummy sit.
| Cure Temperature | Cure Time Test Method |
|---|---|
| 21°C | 50% Relative Humidity, 1/8 inch (0.3175 cm) |
| 21°C | 50% RH; 1/8" (3 mm) |
| Cure Time | Test Method |
|---|---|
| 1,440 min | 50% Relative Humidity, 1/8 inch (0.3175 cm) |
| Fast | |
| 7,200 min | 50% RH; 1/8" (3 mm) |
| Work / Pot Time | Test Method | Temperature |
|---|---|---|
| Long | ||
| 1,800 min | 50% Relative Humidity | 21°C |
| 240 min | 90% Relative Humidity | 32°C |
| Shear Strength | Type | Cure Temperature | Cure Humidity | Substrate | Test Method |
|---|---|---|---|---|---|
| 355 psi | Overlap shear Strength | 21°C | 50 % | Wood(s): Teak | One inch (2.54 cm) overlap specimens (0.093 inch (0.2362 cm thickness). Samples cured at 70°F (21°C), 50% Relative Humidity. |
| 543 psi | Overlap shear Strength | 21°C | 50 % | Wood(s):Pine | One inch (2.54 cm) overlap specimens (0.093 inch (0.2362 cm thickness). Samples cured at 70°F (21°C), 50% Relative Humidity. |
| 518 psi | Overlap shear Strength | 21°C | 50 % | Wood(s): Oak | One inch (2.54 cm) overlap specimens (0.093 inch (0.2362 cm thickness). Samples cured at 70°F (21°C), 50% Relative Humidity. |
| 597 psi | Overlap shear Strength | 21°C | 50 % | Wood(s): Maple | One inch (2.54 cm) overlap specimens (0.093 inch (0.2362 cm thickness). Samples cured at 70°F (21°C), 50% Relative Humidity. |
| 600 psi | Overlap shear Strength | 21°C | 50 % | Wood(s): Fir | One inch (2.54 cm) overlap specimens (0.093 inch (0.2362 cm thickness). Samples cured at 70°F (21°C), 50% Relative Humidity. |
| 407 psi | Overlap shear Strength | 21°C | 50 % | Wood(s): Mahogany | One inch (2.54 cm) overlap specimens (0.093 inch (0.2362 cm thickness). Samples cured at 70°F (21°C), 50% Relative Humidity. |
| 316 psi | Overlap shear Strength | 21°C | 50 % | Metal(s): Steel | One inch (2.54 cm) overlap specimens (0.093 inch (0.2362 cm thickness). Samples cured at 70°F (21°C), 50% Relative Humidity. |
| 197 psi | Overlap shear Strength | 21°C | 50 % | Metal(s): Stainless Steel | One inch (2.54 cm) overlap specimens (0.093 inch (0.2362 cm thickness). Samples cured at 70°F (21°C), 50% Relative Humidity. |
| 203 psi | Overlap shear Strength | 21°C | 50 % | Metal(s): Aluminum | One inch (2.54 cm) overlap specimens (0.093 inch (0.2362 cm thickness). Samples cured at 70°F (21°C), 50% Relative Humidity. |
| 184 psi | Overlap shear Strength | 21°C | 50 % | Metal(s): Brass | One inch (2.54 cm) overlap specimens (0.093 inch (0.2362 cm thickness). Samples cured at 70°F (21°C), 50% Relative Humidity. |
| 176 psi | Overlap shear Strength | 21°C | 50 % | Metal(s): Bronze | One inch (2.54 cm) overlap specimens (0.093 inch (0.2362 cm thickness). Samples cured at 70°F (21°C), 50% Relative Humidity. |
| 182 psi | Overlap shear Strength | 21°C | 50 % | Metal(s): Copper | One inch (2.54 cm) overlap specimens (0.093 inch (0.2362 cm thickness). Samples cured at 70°F (21°C), 50% Relative Humidity. |
| 160 psi | Overlap shear Strength | 21°C | 50 % | Metal(s): Lead | One inch (2.54 cm) overlap specimens (0.093 inch (0.2362 cm thickness). Samples cured at 70°F (21°C), 50% Relative Humidity. |
| 269 psi | Overlap shear Strength | 21°C | 50 % | Metal(s): Zinc (Galvanized) | One inch (2.54 cm) overlap specimens (0.093 inch (0.2362 cm thickness). Samples cured at 70°F (21°C), 50% Relative Humidity. |
| 269 psi | Overlap shear Strength | 21°C | 50 % | Plastics/Polymers: Fiberglass | One inch (2.54 cm) overlap specimens (0.093 inch (0.2362 cm thickness). Samples cured at 70°F (21°C), 50% Relative Humidity. |
| 600 psi | Overlap shear Strength | 21°C | 50 % | Plastics/Polymers: Gelcoat | One inch (2.54 cm) overlap specimens (0.093 inch (0.2362 cm thickness). Samples cured at 70°F (21°C), 50% Relative Humidity. |
| 409 psi | Overlap shear Strength | 21°C | 50 % | Plastics/Polymers: Polycarbonate | One inch (2.54 cm) overlap specimens (0.093 inch (0.2362 cm thickness). Samples cured at 70°F (21°C), 50% Relative Humidity. |
| 149 psi | Overlap shear Strength | 21°C | 50 % | Plastics/Polymers: Acrylic | One inch (2.54 cm) overlap specimens (0.093 inch (0.2362 cm thickness). Samples cured at 70°F (21°C), 50% Relative Humidity. |
| 140 psi | Overlap shear Strength | 21°C | 50 % | Plastics/Polymers: Nylon | One inch (2.54 cm) overlap specimens (0.093 inch (0.2362 cm thickness). Samples cured at 70°F (21°C), 50% Relative Humidity. |
| 262 psi | Overlap shear Strength | 21°C | 50 % | Plastics/Polymers: ABS | One inch (2.54 cm) overlap specimens (0.093 inch (0.2362 cm thickness). Samples cured at 70°F (21°C), 50% Relative Humidity. |
| 66 psi | Overlap shear Strength | 21°C | 50 % | Plastics/Polymers: Polypropylene | One inch (2.54 cm) overlap specimens (0.093 inch (0.2362 cm thickness). Samples cured at 70°F (21°C), 50% Relative Humidity. |
| 0 psi | Overlap shear Strength | 21°C | 50 % | Plastics/Polymers: Polyethylene_x00D_ | One inch (2.54 cm) overlap specimens (0.093 inch (0.2362 cm thickness). Samples cured at 70°F (21°C), 50% Relative Humidity. |
| Tensile Strength | Test Temperature | Test Humidity | Test Method |
|---|---|---|---|
| 1,000 psi | 21°C | 50 % | A 1/8 inch (0.3175 cm) dumbbell specimen with a 1/8 inch (0.3175 cm) square cross section was tested at 2.0 inches/minute (5.08 cm/minute). |
| Elongation | Test Method |
|---|---|
| 874 % | 50% R.H., 70°F (21°C), A 1/8 inch (0.3175 cm) dumbbell specimen with a 1/8 inch (0.3175 cm) square cross section was tested at 2.0 inches/minute (5.08 cm/minute). |
| Shore A Hardness | Shore Hardness Test Method |
|---|---|
| 60 | Cured |
| % Solids | Test Method |
|---|---|
| 97 % | Approx. |
Message sent - We'll get back shortly
Message sent - We'll get back shortly! Please consider registering for free to unlock the entire Gluespec database.
Great! Contact us if you have any additional questions.
You will lose your saved materials unless you register. Please register.
| Manufacturer | Material | Remove |
|---|
Things you can do with checked materials:
| Name | Save Date | View |
|---|
Need help? Our knowledgeable experts help you achieve your goals by giving you application insights. They are available personally to help you before, during or after your search.
