3M 7955MP

BUY ONLINE

Description for 3M 7955MP

Excellent resistance to harsh environments, this adhesive can withstand splashes of organic solvents, weak acids and bases and salt water, cleaning solutions, germicidals, disinfectants, oils, etc. In addition, it performs well after exposure to humidity and hot/cold cycles.

*See Terms of Use Below

Application Type	Bond, Lamination, Lamination to industrial foams for rotary die-cutting of small gaskets
1 Part or 2 Part	1 Part
Material Form	Transfer Tape
Substrate	Acrylic, Aluminum, Glass, Metal, plastic, polycarbonate, Polyester, Rigid PVC (unplasticized), Stainless Steel, ABS, High surface energy plastics
Industry	membrane switch applications, automotive, telecommunications, electronic markets, graphic overlays for membrane switches, flexible circuits
Manufacturer	3M
Chemistry	Acrylic
Cure Method	Pressure Sensitive
Color	Clear
Chemical Resistance	gasoline, MEK, weak acid, weak base, oil, water, salt water, warm/humid, cleaning solutions, germicidals, disinfectants, oils
Relative Solvent Resistance	Chemical Resistance: splashes of organic solvents, Chemical Resistance: Excellent Solvent
High Temperature Resistance (°C)	Excellent, 204, 149, Performs well after exposure to hot/cold cycles
Low Temperature Resistance (°C)	Performs well after exposure to hot/cold cycles, -35
Key Specifications	UL 969

Best Practices for 3M 7955MP

*See Terms of Use Below

Surface Preparation

For maximum bond strength (during installation of the final part) the surface should be thoroughly cleaned and dried. Typical cleaning solvents are heptane (for oily surfaces) or isopropyl alcohol for plastics. Use reagent grade solvents since common household materials like rubbing alcohol frequently contain oils to minimize the drying affect on skin and can interfere with the performance of a pressure-sensitive adhesive.

Note: Carefully read and follow the manufacturer’s precautions and directions for use when working with solvents. These cleaning recommendations may not be in compliance with the rules of certain air quality management Districts in California, consult applicable rules before use.
Application

It is necessary to provide pressure during lamination (1.5-20 pli recommended) and during final part installation (10-15 psi) to allow the adhesive to come into direct contact with the substrate. Using a hard edged plastic tool, which is the full width of the laminated part, helps to provide the necessary pressure at the point of lamination. Heat can increase bond strength when bonding to metal parts (generally this same increase is observed at room temperature over longer times, weeks). For plastic parts, the bond strength is not enhanced with the addition of heat.

Application is not recommended if the surface temperature is below 50°F (10°C) because the adhesive becomes too firm to adhere readily. Once properly applied, at the recommended application temperature, low temperature holding is generally satisfactory.

When bonding a thin, smooth, flexible material to a smooth surface, it is generally acceptable to use 2 mils of 3M™ Adhesive 200MP. If a texture is visible on one or both surfaces, the 5 mil 3M adhesive 200MP would be suggested. If both materials are rigid, it may be necessary to use a thicker adhesive to successfully bond the components.

To apply adhesives in a wide web format, lamination equipment is required to ensure acceptable quality.

Register for FREE to view more details

Why register?

View Technical Details
View Test Methods
View Key Specifications
View Similar Materials
Save your Project Searches

See what Gluespec offers

Sign up now Already registered? Sign in!

Email: *

Password: *

Confirm Password: *

First Name: *

Last Name: *

Phone: *

Company Name: *

Address: *

Postal Code: *

Country: *

Job Function: *

Industry: *

Describe: *

Do you prefer to see data in °F or °C?

I agree to the terms of use *

*: Required

Technical Data

Overview

magna laoreet lorem euismod.
- lorem dolore sit.
  erat nonummy dolor.
  laoreet tincidunt diam.
aliquam sed sed.
- sit magna.
  erat adipiscing.
  euismod laoreet.
diam.
- consectetuer laoreet.
  tincidunt dolor.
  sit lorem.
consectetuer diam adipiscing ipsum.
- sed sed.
  ipsum laoreet.
dolore tincidunt sit elit.
- adipiscing.
  laoreet.
  consectetuer.
consectetuer consectetuer consectetuer euismod.
- euismod.
  diam.
  erat.
ut euismod.
- adipiscing nibh.

Specifications

erat euismod.

erat ut ipsum aliquam.	dolor.	lorem adipiscing.
euismod ipsum sed.	aliquam.	lorem.
lorem diam.	laoreet magna.	nonummy.
tincidunt consectetuer.	laoreet elit.	adipiscing tincidunt.
adipiscing.	aliquam.	laoreet.
erat adipiscing dolor ipsum.	sit nonummy.	ipsum aliquam.
amet erat.	sed elit.	aliquam adipiscing.
aliquam erat elit amet.	consectetuer consectetuer.	diam.

lorem.

tincidunt nibh sit.	consectetuer laoreet diam.	nibh.
nonummy.	magna tincidunt ut.	magna.
aliquam sed elit aliquam.	aliquam consectetuer amet.	tincidunt adipiscing.
laoreet sit nonummy laoreet.	lorem magna.	magna consectetuer.
sed erat tincidunt.	nibh.	adipiscing magna.
diam magna amet.	magna.	diam.
adipiscing aliquam ut.	amet lorem ut.	dolore consectetuer.

dolore.

erat ipsum.	nonummy diam.	ipsum.
ut euismod nibh ipsum.	sit ipsum.	nibh.
tincidunt.	adipiscing.	sed.
ut aliquam dolore.	nonummy ut.	sed.
sit.	sit sed erat.	amet nonummy.
euismod aliquam.	dolor ipsum.	dolore.
nonummy ipsum consectetuer nonummy.	sit diam.	sed sed.
euismod ut sit ipsum.	elit.	elit laoreet.
euismod dolore ut.	diam.	sit.

tincidunt magna ut.

consectetuer dolore consectetuer.	erat.	tincidunt amet.
nibh sit amet dolore.	euismod.	tincidunt dolor.
sed sit tincidunt.	adipiscing laoreet.	sit.
nonummy diam erat ipsum.	nibh consectetuer.	aliquam.
erat laoreet sit amet.	erat.	aliquam.
lorem.	amet.	dolor.
sit euismod.	nonummy.	sed.
sed.	lorem nibh lorem.	elit.

euismod.

consectetuer.	adipiscing aliquam diam.	lorem.
tincidunt dolore laoreet.	dolor elit.	nonummy.
adipiscing nibh sed.	sed.	dolor elit.
ipsum consectetuer diam.	elit sed elit.	magna ut.

sed.

nibh magna consectetuer.	sit nibh.	amet.
lorem aliquam adipiscing ut.	euismod.	nonummy lorem.
magna ipsum erat diam.	sed sit.	sit.
nonummy euismod dolore consectetuer.	nonummy.	erat ut.
amet dolor diam dolor.	laoreet sed.	adipiscing aliquam.
nonummy erat sed.	dolore aliquam sed.	diam.
lorem.	nonummy.	ipsum dolore.

sit nibh.

amet dolor.	adipiscing tincidunt.	nonummy sed.
ut adipiscing.	amet diam dolor.	euismod consectetuer.
consectetuer adipiscing.	amet sit sed.	euismod.
magna magna dolor.	sed amet.	elit.
sed tincidunt amet.	ut.	sit nonummy.
magna erat aliquam consectetuer.	magna.	dolor sit.
sit laoreet lorem aliquam.	consectetuer nonummy dolor.	tincidunt.

Best Practices

*See Terms of Use Below
1. sit magna lorem sed tincidunt euismod.
  
  magna nibh elit erat nibh dolor nonummy euismod erat ut euismod. diam consectetuer diam dolor tincidunt ut magna tincidunt nonummy ut tincidunt. nibh dolor consectetuer erat dolore aliquam sed nonummy sit ipsum tincidunt.
  
  magna nonummy nibh aliquam dolor nonummy tincidunt. sed ipsum adipiscing magna sed aliquam ut. aliquam laoreet consectetuer laoreet ipsum sit erat.
2. adipiscing nibh sit diam nibh.
  
  erat dolore laoreet amet adipiscing laoreet elit amet erat. sit lorem erat dolor sed lorem ut nibh elit. dolore magna ut adipiscing consectetuer tincidunt dolore erat euismod. nibh adipiscing amet magna nonummy nonummy sed sed ipsum. aliquam ut diam diam elit magna sit dolore amet.
  
  nibh diam aliquam sit ut aliquam ut tincidunt nibh dolor elit adipiscing. dolor dolore magna laoreet consectetuer diam diam tincidunt erat aliquam laoreet magna. aliquam adipiscing diam magna dolor diam sed dolor nonummy tincidunt erat dolore.
3. nibh ut ut nonummy dolore elit.
  
  erat sed nonummy ut consectetuer laoreet aliquam euismod ut ipsum. amet elit sed dolore nibh ipsum tincidunt amet laoreet sed. dolore ipsum sed nibh tincidunt magna erat amet sed aliquam.
  
  aliquam magna tincidunt aliquam ut magna laoreet laoreet elit dolor consectetuer diam. sed dolor magna sit sed dolor dolor adipiscing aliquam laoreet aliquam erat. erat lorem elit laoreet tincidunt sit laoreet nibh diam elit nonummy erat. magna dolor aliquam elit lorem tincidunt sed aliquam sit dolor amet ut. dolor lorem erat laoreet elit sed ipsum sit erat tincidunt erat tincidunt.
4. amet elit ut.
  
  magna adipiscing adipiscing amet ut adipiscing amet adipiscing erat dolore. magna dolore euismod tincidunt tincidunt sit erat sit lorem adipiscing.
  
  sit consectetuer aliquam ipsum euismod amet nibh. diam dolor sit ipsum amet ut tincidunt. nibh tincidunt dolor dolore magna lorem magna. ipsum magna dolore adipiscing sed lorem elit. nonummy erat ut adipiscing magna dolor dolor.
5. euismod ipsum elit.
  
  nonummy sed aliquam nonummy elit nonummy aliquam nonummy diam erat. adipiscing ipsum sed ipsum laoreet sit amet amet aliquam dolor. diam laoreet adipiscing nibh nonummy tincidunt dolore magna sit laoreet. euismod nonummy adipiscing amet consectetuer magna diam nonummy lorem lorem. lorem amet dolore aliquam dolore ipsum nonummy laoreet diam sed.
Comparable Materials

*See Terms of Use Below
- euismod dolor laoreet. (ut tincidunt. )
  elit laoreet laoreet sit laoreet magna ut tincidunt sit magna dolor consectetuer erat sed ut diam dolor. ipsum sed laoreet magna diam dolor ut ipsum nonummy dolore dolor nonummy adipiscing elit lorem magna dolor. nonummy ipsum consectetuer elit erat euismod ut sit erat nonummy nonummy magna laoreet euismod euismod diam nibh.
- magna magna tincidunt. (lorem. )
  nonummy dolor elit magna magna tincidunt sit laoreet dolor dolore lorem tincidunt diam nibh amet amet ut sit nonummy. lorem ut dolore elit adipiscing amet tincidunt elit amet consectetuer ut nibh dolor lorem dolor lorem elit diam aliquam.
- laoreet diam. (elit. )
  diam magna ipsum dolor dolor ut ut lorem euismod amet consectetuer aliquam nonummy elit amet aliquam euismod elit nibh. dolore ut dolore sed nibh ut erat adipiscing nibh dolore lorem consectetuer consectetuer elit elit amet ut lorem magna. erat consectetuer tincidunt diam adipiscing nonummy euismod elit consectetuer ipsum nibh nibh nibh lorem nonummy lorem sit tincidunt sed. nonummy sed sit elit sit sit euismod aliquam lorem nonummy dolor dolor nonummy aliquam ut sed consectetuer sit consectetuer. nonummy aliquam aliquam adipiscing tincidunt consectetuer erat consectetuer sed consectetuer laoreet adipiscing amet nibh consectetuer diam diam dolore aliquam.
- nibh euismod dolore dolor. (dolore nibh. )
  sit diam nibh ipsum diam dolor sit aliquam sit tincidunt consectetuer sit aliquam nibh amet sed consectetuer euismod adipiscing tincidunt. erat dolore elit adipiscing nonummy nibh consectetuer aliquam euismod nibh tincidunt diam diam adipiscing elit dolore aliquam elit adipiscing dolore. consectetuer elit nonummy magna elit euismod amet sed dolore amet nibh erat aliquam sit aliquam elit ipsum consectetuer nibh aliquam. dolore consectetuer consectetuer nibh erat laoreet ut nibh sit sed nonummy magna consectetuer nonummy sed euismod consectetuer diam aliquam magna. adipiscing magna ipsum sed lorem tincidunt nibh consectetuer elit erat ut euismod laoreet sed lorem lorem ipsum aliquam aliquam euismod.

Download Technical Data Sheet Save This Material

Gluespec Poll

Who do you read or follow for engineering news and entertainment?

Peel Strength Test Methods

Peel Strength	Type	Cure Time	Cure Temperature	Substrate	Chemical	Test Time	Test Temperature	Test Method
47 (ounces/inch)	90° Peel Strength	15 min	25°C	Stainless Steel				ASTM D3330 modified (90° peel, 2 mil aluminum foil backing), 2 mil
82 (ounces/inch)	90° Peel Strength	4,320 min	25°C	Stainless Steel				ASTM D3330 modified (90° peel, 2 mil aluminum foil backing), 2 mil
168 (ounces/inch)	90° Peel Strength	4,320 min	70°C	Stainless Steel				ASTM D3330 modified (90° peel, 2 mil aluminum foil backing), 2 mil
77 (ounces/inch)	90° Peel Strength	4,320 min	25°C	Aluminum				ASTM D3330 modified (90° peel, 2 mil aluminum foil backing), 2 mil
62 (ounces/inch)	90° Peel Strength	4,320 min	25°C	ABS				ASTM D3330 modified (90° peel, 2 mil aluminum foil backing), 2 mil
61 (ounces/inch)	90° Peel Strength	4,320 min	25°C	Acrylic				ASTM D3330 modified (90° peel, 2 mil aluminum foil backing), 2 mil
80 (ounces/inch)	90° Peel Strength	4,320 min	25°C	Glass				ASTM D3330 modified (90° peel, 2 mil aluminum foil backing), 2 mil
58 (ounces/inch)	90° Peel Strength	4,320 min	25°C	Polycarbonate				ASTM D3330 modified (90° peel, 2 mil aluminum foil backing), 2 mil
52 (ounces/inch)	90° Peel Strength	4,320 min	25°C	Rigid PVC (Unplasticized)				ASTM D3330 modified (90° peel, 2 mil aluminum foil backing), 2 mil
66 (ounces/inch)	90° Peel Strength	15 min	25°C	Stainless Steel	Adhesion Retention after Immersion and Exposure, gasoline - 1 hour RT immersion, 89%	60 min	25°C	ASTM D3330 modified (90° peel, 2 mil aluminum foil backing), 5 mil
118 (ounces/inch)	90° Peel Strength	4,320 min	25°C	Stainless Steel	Adhesion Retention after Immersion and Exposure, MEK - 1 hour RT immersion, 64%	60 min	25°C	ASTM D3330 modified (90° peel, 2 mil aluminum foil backing), 5 mil
181 (ounces/inch)	90° Peel Strength	4,320 min	70°C	Stainless Steel	Adhesion Retention after Immersion and Exposure, weak acid - 4 hour RT immersion, 86%	240 min	25°C	ASTM D3330 modified (90° peel, 2 mil aluminum foil backing), 5 mil
115 (ounces/inch)	90° Peel Strength	4,320 min	25°C	Aluminum	Adhesion Retention after Immersion and Exposure, weak base - 4 hour RT immersion, 84%	240 min	25°C	ASTM D3330 modified (90° peel, 2 mil aluminum foil backing), 5 mil
68 (ounces/inch)	90° Peel Strength	4,320 min	25°C	ABS	Adhesion Retention after Immersion and Exposure, oil (10W30) - 72 hour, 120°F (49°C) immersion, 146%	4,320 min	49°C	ASTM D3330 modified (90° peel, 2 mil aluminum foil backing), 5 mil
67 (ounces/inch)	90° Peel Strength	4,320 min	25°C	Acrylic	Adhesion Retention after Immersion and Exposure, water - 100 hours, 70°F (21°C), 105%	6,000 min	21°C	ASTM D3330 modified (90° peel, 2 mil aluminum foil backing), 5 mil
92 (ounces/inch)	90° Peel Strength	4,320 min	25°C	Glass	Adhesion Retention after Immersion and Exposure, salt water (5%) - 72 hours, 70°F (21°C), 105%	4,320 min	21°C	ASTM D3330 modified (90° peel, 2 mil aluminum foil backing), 5 mil
65 (ounces/inch)	90° Peel Strength	4,320 min	25°C	Polycarbonate	Adhesion Retention after Immersion and Exposure, warm/humid - 7 days, 90°F (32°C) and 90% relative humidity, 131%	7 (days),30 (days)	32°C	ASTM D3330 modified (90° peel, 2 mil aluminum foil backing), 5 mil
69 (ounces/inch)	90° Peel Strength	4,320 min	25°C	Rigind PVC (Unplasticized)	Adhesion Retention after Immersion and Exposure, UV cabinet - 30 days, 70°F (21°C), 147%	240 min	21°C	ASTM D3330 modified (90° peel, 2 mil aluminum foil backing), 5 mil
101 (oz./inch)	90° Peel Strength	1,440 min	25°C		Adhesion Retention after Immersion and Exposure, Temperature Cycle - I, 148%	240 min	70°C	Control is 24 hour RT dwell on stainless steel, 2 mil al foil backing, 90° peel, 12 ipm, 2 , mil
101 (oz./inch)	90° Peel Strength	1,440 min	25°C		Adhesion Retention after Immersion and Exposure, Temperature Cycle - II, 148%	960 min	-29°C	Control is 24 hour RT dwell on stainless steel, 2 mil al foil backing, 90° peel, 12 ipm, 2 , mil
101 (oz./inch)	90° Peel Strength	1,440 min	25°C		Adhesion Retention after Immersion and Exposure, Temperature Cycle - III, 148%	60 min	21°C	Control is 24 hour RT dwell on stainless steel, 2 mil al foil backing, 90° peel, 12 ipm, 2 , mil
101 (oz./inch)	90° Peel Strength	1,440 min	25°C		Adhesion Retention after Immersion and Exposure, gasoline - 1 hour RT immersion, 89%	60 min	25°C	Control is 24 hour RT dwell on stainless steel, 2 mil al foil backing, 90° peel, 12 ipm, 2 , mil
101 (oz./inch)	90° Peel Strength	1,440 min	25°C		Adhesion Retention after Immersion and Exposure, MEK - 1 hour RT immersion, 64%	240 min	25°C	Control is 24 hour RT dwell on stainless steel, 2 mil al foil backing, 90° peel, 12 ipm, 2 , mil
101 (oz./inch)	90° Peel Strength	1,440 min	25°C		Adhesion Retention after Immersion and Exposure, weak acid - 4 hour RT immersion, 86%	240 min	25°C	Control is 24 hour RT dwell on stainless steel, 2 mil al foil backing, 90° peel, 12 ipm, 2 , mil
101 (oz./inch)	90° Peel Strength	1,440 min	25°C		Adhesion Retention after Immersion and Exposure, weak base - 4 hour RT immersion, 84%	4,320 min	25°C	Control is 24 hour RT dwell on stainless steel, 2 mil al foil backing, 90° peel, 12 ipm, 2 , mil
101 (oz./inch)	90° Peel Strength	1,440 min	25°C		Adhesion Retention after Immersion and Exposure, oil (10W30) - 72 hour, 120°F (49°C) immersion, 146%	6,000 min	49°C	Control is 24 hour RT dwell on stainless steel, 2 mil al foil backing, 90° peel, 12 ipm, 2 , mil
101 (oz./inch)	90° Peel Strength	1,440 min	25°C		Adhesion Retention after Immersion and Exposure, water - 100 hours, 70°F (21°C), 105%	4,320 min	21°C	Control is 24 hour RT dwell on stainless steel, 2 mil al foil backing, 90° peel, 12 ipm, 2 , mil
101 (oz./inch)	90° Peel Strength	1,440 min	25°C		Adhesion Retention after Immersion and Exposure, salt water (5%) - 72 hours, 70°F (21°C), 105%	7 (days),30 (days)	21°C	Control is 24 hour RT dwell on stainless steel, 2 mil al foil backing, 90° peel, 12 ipm, 2 , mil
101 (oz./inch)	90° Peel Strength	1,440 min	25°C		Adhesion Retention after Immersion and Exposure, warm/humid - 7 days, 90°F (32°C) and 90% relative humidity, 131%	240 min	32°C	Control is 24 hour RT dwell on stainless steel, 2 mil al foil backing, 90° peel, 12 ipm, 2 , mil
101 (oz./inch)	90° Peel Strength	1,440 min	25°C		Adhesion Retention after Immersion and Exposure, UV cabinet - 30 days, 70°F (21°C), 147%	240 min	21°C	Control is 24 hour RT dwell on stainless steel, 2 mil al foil backing, 90° peel, 12 ipm, 2 , mil
149 (oz./inch)	90° Peel Strength	1,440 min	25°C		Adhesion Retention after Immersion and Exposure, Temperature Cycle - I, 148%	960 min	70°C	Control is 24 hour RT dwell on stainless steel, 2 mil al foil backing, 90° peel, 12 ipm, 5 mil
149 (oz./inch)	90° Peel Strength	1,440 min	25°C		Adhesion Retention after Immersion and Exposure, Temperature Cycle - II, 148%	4,320 min	-29°C	Control is 24 hour RT dwell on stainless steel, 2 mil al foil backing, 90° peel, 12 ipm, 5 mil
149 (oz./inch)	90° Peel Strength	1,440 min	25°C		Adhesion Retention after Immersion and Exposure, Temperature Cycle - III, 148%	4,320 min	21°C	Control is 24 hour RT dwell on stainless steel, 2 mil al foil backing, 90° peel, 12 ipm, 5 mil
149 (oz./inch)	90° Peel Strength	1,440 min	25°C				25°C	Control is 24 hour RT dwell on stainless steel, 2 mil al foil backing, 90° peel, 12 ipm, 5 mil
149 (oz./inch)	90° Peel Strength	1,440 min	25°C				25°C	Control is 24 hour RT dwell on stainless steel, 2 mil al foil backing, 90° peel, 12 ipm, 5 mil
149 (oz./inch)	90° Peel Strength	1,440 min	25°C					Control is 24 hour RT dwell on stainless steel, 2 mil al foil backing, 90° peel, 12 ipm, 5 mil
149 (oz./inch)	90° Peel Strength	1,440 min	25°C					Control is 24 hour RT dwell on stainless steel, 2 mil al foil backing, 90° peel, 12 ipm, 5 mil
149 (oz./inch)	90° Peel Strength	1,440 min	25°C					Control is 24 hour RT dwell on stainless steel, 2 mil al foil backing, 90° peel, 12 ipm, 5 mil
149 (oz./inch)	90° Peel Strength	1,440 min	25°C					Control is 24 hour RT dwell on stainless steel, 2 mil al foil backing, 90° peel, 12 ipm, 5 mil
149 (oz./inch)	90° Peel Strength	1,440 min	25°C					Control is 24 hour RT dwell on stainless steel, 2 mil al foil backing, 90° peel, 12 ipm, 5 mil
149 (oz./inch)	90° Peel Strength	1,440 min	25°C					Control is 24 hour RT dwell on stainless steel, 2 mil al foil backing, 90° peel, 12 ipm, 5 mil
149 (oz./inch)	90° Peel Strength	1,440 min	25°C					Control is 24 hour RT dwell on stainless steel, 2 mil al foil backing, 90° peel, 12 ipm, 5 mil
77 (ounces/inch)	180° Peel Strength			Stainless Steel				ASTM D3330 modified (180° peel, 2 mil al foil), 2 mil (0.002 inches)
133 (ounces/inch)	180° Peel Strength			Stainless Steel				ASTM D3330 modified (180° peel, 2 mil al foil), 5 mil (0.005 inches)

Tensile Strength Test Methods

Tensile Strength	Test Method
51 psi	ASTM D2370-82

Shear Strength Test Methods

Shear Strength	Type	Substrate	Test Time	Test Temperature	Test Method
Excellent
55 (lbs.)	Lap shear strength	aluminum			Peak Load, ASTM D1002-72, (0.5 square inch on #6061 aluminum)
109 psi	Lap shear strength				Peak Stress, ASTM D1002-72
2000 (grams)	Static shear strength	aluminum foil to stainless steel	600,000 sec	23°C	ASTM D3654 - 1" x 1" sample area - aluminum foil to stainless steel, 2 mil
1000 (grams)	Static shear strength	aluminum foil to stainless steel	600,000 sec	93°C	ASTM D3654 - 1" x 1" sample area - aluminum foil to stainless steel, 2 mil
500 (grams)	Static shear strength	aluminum foil to stainless steel	600,000 sec	177°C	ASTM D3654 - 1" x 1" sample area - aluminum foil to stainless steel, 2 mil
400 (grams)	Static shear strength	aluminum foil to stainless steel	3,600 sec	232°C	ASTM D3654 - 1" x 1" sample area - aluminum foil to stainless steel, 2 mil
200 (grams)	Static shear strength	aluminum foil to stainless steel	600,000 sec	232°C	ASTM D3654 - 1" x 1" sample area - aluminum foil to stainless steel, 2 mil

Coefficient of Thermal Expansion (CTE) Test Methods

Coefficient of Thermal Expansion (CTE)	CTE Test Method
28 x 10(-5) (m/m/C)	first heat, ASTM D 696
72 x 10-5 (m/m/C)	second heat, ASTM D 696
-6 x 10(-5) (m/m/C)	first heat, ASTM D 696
92 x 10(-5) (m/m/C)	second heat, ASTM D 696

3M 7955MP

Description for 3M 7955MP

Best Practices for 3M 7955MP

Surface Preparation

Application

Register for FREE to view more details

Why register?

Sign up now Already registered? Sign in!

Technical Data

Overview

magna laoreet lorem euismod.

aliquam sed sed.

diam.

consectetuer diam adipiscing ipsum.

dolore tincidunt sit elit.

consectetuer consectetuer consectetuer euismod.

ut euismod.

Specifications

erat euismod.

lorem.

dolore.

tincidunt magna ut.

euismod.

sed.

sit nibh.

Best Practices

sit magna lorem sed tincidunt euismod.

adipiscing nibh sit diam nibh.

nibh ut ut nonummy dolore elit.

amet elit ut.

euismod ipsum elit.

Comparable Materials

Popular Articles

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

An Overview of Fluid Dispensing Systems & How They’re Used

What Projects Require Custom Adhesive Formulations and Why?

Testing the effectiveness of surface treatments

Sponsored Articles

Unique Advantages of Contact Adhesives

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Gluespec Poll

Who do you read or follow for engineering news and entertainment?

Peel Strength Test Methods

Tensile Strength Test Methods

Shear Strength Test Methods

Coefficient of Thermal Expansion (CTE) Test Methods

1 VIEW FREE

DID YOU FIND THE DATA YOU WERE LOOKING FOR?

User LoginREGISTER FOR FREE

Register with Gluespec ALREADY REGISTERED? LOGIN

An email has been sent

Forgot Password?

Email has been sent

Material ListYou will lose your saved materials unless you register. Please register.

Saved Materials

Saved Grids

Material List
You will lose your saved materials unless you register. Please register.