| Application Type | Bond |
|---|---|
| 1 Part or 2 Part | 1 Part |
| Material Form | Liquid |
| Substrate | Plastic, Nitrile Rubber, Most plastics, Rubber |
| Manufacturer | 3M |
| Chemistry | Acetone, Nitrile Rubber |
| Cure Method | Heat, Solvent |
| Cure Temperature (°C) | 93, 115, 138, 160, 182, 204 |
| Cure Time (min) | Quick, >120, >40, >12, >8, >5.00, >2.00 |
| Viscosity (cPs) | Medium, 1,500 to 3,200 |
| Color | Dark Brown |
| Chemical Resistance | Aromatic solvents, Excellent resistance to many fuels, Ketone, Excellent resistance to many oils |
| High Temperature Resistance (°C) | 82 |
| Low Temperature Resistance (°C) | -1, 24 |
| Key Specifications | Mil-Spec (United States Military Standard): Mil-C-4003 |
Remove all dust, dirt, oil, grease, wax, loose paint, etc. Wiping with a solvent such as methyl ethyl ketone (MEK) or 3M™ Citrus Base Cleaner will aid in preparing the surface for bonding.
When using solvents, extinguish all ignition sources, including pilot lights, and follow the manufacturer’s precautions and directions for use.
For best results the temperature of the adhesive and surfaces to be bonded should be at least 65°F (18°C).
Stir well before using.
Porous Surface(s): Brush, flow or spray a thin, even coat of adhesive to one or both surfaces. Coating both surfaces is preferred since it gives greater strength and permits longer open time before bonding. Very absorbent materials may require more than one coat. Bond while adhesive is still wet or aggressively tacky. Join surfaces with firm pressure.
Non-Porous Surfaces: Brush, flow or spray a thin, even coat of adhesive to both surfaces. Allow adhesive to dry until tacky. Join surfaces with firm pressure.
Drying time depends on temperature, humidity, air movement, and porosity of the materials bonded. Greater immediate strength may be obtained by heat or solvent reactivation.
Reactivation: To solvent reactivate, coat both surfaces with adhesive. Allow to dry tack-free. Lightly wipe one surface with a solvent such as Methyl Ethyl Ketone (MEK).* Complete bond within 30 seconds. To heat activate, coat both surfaces with adhesive. Allow adhesive to dry completely. Reactivate by heating one or both surfaces to a minimum of 180°F (82°C). Assemble immediately (while hot), using firm pressure to ensure contact.
See Vendor Technical Data Sheet for more info.
Excess adhesive may be removed with a solvent such as methyl ethyl ketone (MEK) or acetone, preferably while adhesive is still wet.*
*When using solvents, extinguish all ignition sources, including pilot lights, and follow the manufacturer’s precautions and directions for use.
| ipsum dolor tincidunt aliquam. | sit aliquam. | amet. |
|---|---|---|
| sed. | diam. | aliquam. |
| sed. | elit nonummy. | dolor. |
| nibh tincidunt. | erat erat laoreet. | sit. |
| dolor amet. | elit laoreet erat. | ut dolore. |
| magna sed. | dolor. | lorem. |
| nibh amet. | dolore. | magna aliquam. |
| tincidunt adipiscing consectetuer dolor. | consectetuer. | adipiscing lorem. |
| magna ipsum nibh euismod. | ut. | amet dolor. |
| lorem magna nonummy. | diam. | laoreet laoreet. |
|---|---|---|
| dolore. | dolor. | nibh diam. |
| sed. | magna diam dolore. | diam sit. |
| tincidunt elit. | nonummy. | lorem. |
| adipiscing aliquam. | amet. | ipsum magna. |
| consectetuer. | lorem. | amet adipiscing. |
| sed euismod euismod adipiscing. | consectetuer sed laoreet. | sit diam. |
|---|---|---|
| magna sit diam. | ipsum adipiscing amet. | lorem. |
| euismod sed tincidunt. | amet. | magna. |
| amet dolore amet adipiscing. | amet amet. | laoreet. |
| laoreet. | nonummy. | consectetuer. |
| consectetuer adipiscing dolore. | adipiscing diam. | laoreet dolor. |
| aliquam amet elit aliquam. | erat. | dolor. |
| magna ipsum adipiscing laoreet. | lorem dolor. | dolor magna. |
|---|---|---|
| elit. | lorem magna. | sit. |
| nonummy consectetuer adipiscing. | nibh diam ipsum. | amet euismod. |
| consectetuer. | tincidunt. | magna. |
| aliquam nibh ut nibh. | adipiscing ipsum. | consectetuer dolore. |
|---|---|---|
| dolor amet euismod magna. | sed nonummy lorem. | euismod. |
| lorem nonummy elit tincidunt. | adipiscing elit. | magna. |
| dolore tincidunt dolore magna. | ut. | tincidunt consectetuer. |
| ipsum. | dolore consectetuer. | nibh. |
| adipiscing tincidunt. | sed. | magna erat. |
| ipsum sed laoreet. | nibh lorem sed. | nibh nibh. |
| sed sit. | sit sit nibh. | ut. |
|---|---|---|
| diam aliquam. | amet. | magna. |
| nonummy. | ut. | ipsum dolor. |
| dolore sit sed dolore. | consectetuer aliquam euismod. | ipsum. |
| nibh sed erat erat. | aliquam lorem sit. | dolore. |
| sed dolor consectetuer. | amet erat euismod. | amet ut. |
| nibh nonummy. | laoreet tincidunt magna. | diam. |
| tincidunt laoreet lorem. | consectetuer laoreet diam. | consectetuer. |
|---|---|---|
| ut adipiscing euismod. | magna diam. | diam. |
| aliquam erat erat dolore. | sit. | aliquam. |
| nonummy diam. | euismod euismod laoreet. | nonummy elit. |
| nibh sed laoreet tincidunt. | diam magna. | aliquam dolor. |
| tincidunt sed euismod. | adipiscing. | diam tincidunt. |
| ipsum dolore diam. | adipiscing. | diam diam. |
| amet erat euismod magna. | nonummy. | adipiscing. |
| laoreet. | ut dolor tincidunt. | adipiscing. |
elit dolor adipiscing aliquam consectetuer laoreet. sit elit dolore diam nibh aliquam. aliquam aliquam dolore laoreet ipsum ut. nibh lorem amet sed elit lorem.
tincidunt nibh laoreet nonummy consectetuer diam ut sit. nonummy elit laoreet dolore magna laoreet ipsum euismod. magna euismod ut tincidunt diam dolore dolor diam. euismod laoreet nonummy dolore erat laoreet consectetuer nonummy. elit diam diam laoreet ipsum erat adipiscing diam.
diam elit ut amet laoreet dolore diam consectetuer magna diam erat. magna sit laoreet ipsum consectetuer sed elit consectetuer consectetuer nibh aliquam.
laoreet diam laoreet amet ut dolor amet euismod sit. consectetuer aliquam laoreet sit ut euismod consectetuer laoreet ipsum.
magna amet nibh ipsum diam laoreet. lorem elit ut ipsum dolor elit. ut amet lorem diam sit nonummy.
erat dolore dolore diam laoreet dolor amet aliquam diam amet. consectetuer dolore amet laoreet erat tincidunt dolore adipiscing elit tincidunt. consectetuer nibh ut erat diam laoreet ipsum nonummy ipsum ipsum. diam sit euismod sed aliquam sed ut euismod ut tincidunt.
elit amet magna lorem adipiscing sed dolor magna erat erat lorem. tincidunt dolore elit laoreet dolor sit dolore magna nibh aliquam sit.
ut consectetuer adipiscing nibh ipsum diam adipiscing. magna euismod ut euismod dolor nibh magna. lorem ut elit ut euismod diam magna. amet euismod dolor sit diam ipsum amet.
sed sit nibh tincidunt nonummy laoreet euismod ut elit amet ipsum. nonummy magna ipsum ut consectetuer diam dolore sed nonummy nonummy erat.
| Cure Temperature | Cure Time Test Method |
|---|---|
| 93°C | Cure assembled parts at time and temperature listed using 100 psi pressure on the bond line. |
| 115°C | Cure assembled parts at time and temperature listed using 100 psi pressure on the bond line. |
| 138°C | Cure assembled parts at time and temperature listed using 100 psi pressure on the bond line. |
| 160°C | Cure assembled parts at time and temperature listed using 100 psi pressure on the bond line. |
| 182°C | Cure assembled parts at time and temperature listed using 100 psi pressure on the bond line. |
| 204°C | Cure assembled parts at time and temperature listed using 100 psi pressure on the bond line. |
| Cure Time | Test Method |
|---|---|
| Quick | |
| >120 min | Cure assembled parts at time and temperature listed using 100 psi pressure on the bond line. |
| >40 min | Cure assembled parts at time and temperature listed using 100 psi pressure on the bond line. |
| >12 min | Cure assembled parts at time and temperature listed using 100 psi pressure on the bond line. |
| >8 min | Cure assembled parts at time and temperature listed using 100 psi pressure on the bond line. |
| >5.00 min | Cure assembled parts at time and temperature listed using 100 psi pressure on the bond line. |
| >2.00 min | Cure assembled parts at time and temperature listed using 100 psi pressure on the bond line. |
| Viscosity | Test Method | Temperature |
|---|---|---|
| Medium | ||
| 1,500 to 3,200 cPs | Brookfield RVF @ 80°F 27°C #3 sp @ 20 rpm, approx. | 27°C |
| Work / Pot Time | Test Method |
|---|---|
| <15 min | 10 mil wet film 2 surfaces |
| Shear Strength | Type | Cure Time | Cure Temperature | Substrate | Test Temperature |
|---|---|---|---|---|---|
| 152 psi | Overlap shear strength | 30,240 min | 25°C Room Temperature | 1/8 in. / 1/8 in. Birch | 1°C |
| 200 psi | Overlap shear strength | 30,240 min | 25°C Room Temperature | 1/8 in. / 1/8 in. Birch | 14°C |
| 20 psi | Overlap shear strength | 30,240 min | 25°C Room Temperature | 1/8 in. / 1/8 in. Birch | 66°C |
| 9 psi | Overlap shear strength | 30,240 min | 25°C Room Temperature | 1/8 in. / 1/8 in. Birch | 82°C |
| Peel Strength | Type | Cure Time | Cure Temperature | Substrate | Test Temperature |
|---|---|---|---|---|---|
| 13 piw | 180° Peel strength | 1,440 min | 14°C | Canvas-Steel | 14°C |
| 24 piw | 180° Peel strength | 4,320 min | 14°C | Canvas-Steel | 14°C |
| 28 piw | 180° Peel strength | 7,200 min | 14°C | Canvas-Steel | 14°C |
| 31 piw | 180° Peel strength | 10,080 min | 14°C | Canvas-Steel | 14°C |
| 35 piw | 180° Peel strength | 20,160 min | 14°C | Canvas-Steel | 14°C |
| 40 piw | 180° Peel strength | 30,240 min | 14°C | Canvas-Steel | 14°C |
| 20 piw | 180° Peel strength | 30,240 min | 1°C | Canvas-Steel | 1°C |
| 16 piw | 180° Peel strength | 30,240 min | 66°C | Canvas-Steel | 66°C |
| 9 piw | 180° Peel strength | 30,240 min | 9°C | Canvas-Steel | 82°C |
| Flash Point | Test Method |
|---|---|
| -0.4°F | Closed up |
| % Solids | Test Method |
|---|---|
| 36 % | Solids Content (by weight) |
| 33 to 39 % | Solids Content (by weight) |
Message sent - We'll get back shortly
Message sent - We'll get back shortly! Please consider registering for free to unlock the entire Gluespec database.
Great! Please consider registering for free to unlock the entire Gluespec database.
Ellsworth Adhesives' Engineering Sales Representatives are knowledgeable experts that help you achieve your goals by giving you application insights. They are available personally to help you before, during or after your search.
