| Application Type | Bond |
|---|---|
| 1 Part or 2 Part | 1 Part |
| Material Form | Double-Coated Tape |
| Substrate | ABS, Stainless Steel |
| Manufacturer | 3M |
| Chemistry | Isopropyl alcohol |
| Cure Method | Pressure Sensitive |
| Chemical Resistance | Exceptional |
| High Temperature Resistance (°C) | 149, 93 |
| Key Specifications | TSCA |
To obtain optimum adhesion, the bonding surfaces must be clean, dry and well unified. Some typical surface cleaning solvents are isopropyl alcohol or heptane.*
*Note: Carefully read and follow the manufacturer’s precautions and directions for use when working with solvents. These cleaning recommendations may not be compliant with the rules of certain Air Quality Management Districts in California
consult applicable rules before use.
Bond strength is dependent upon the amount of adhesive-to-surface contact developed. Firm application pressure helps develop better adhesive contact and improves bond strength.
Ideal tape application temperature range is 70°F to 100°F (21°C to 38°C). Initial tape application to surfaces at temperatures below 50°F (10°C) is not recommended because the adhesive becomes too firm to adhere readily. However, once properly applied, low temperature holding is generally satisfactory.
| diam. | erat. | dolor. |
|---|---|---|
| magna sit amet. | sit magna nibh. | ut. |
| tincidunt elit diam. | diam. | consectetuer. |
| tincidunt dolor dolor sit. | consectetuer amet. | erat amet. |
|---|---|---|
| erat elit dolore. | magna. | magna. |
| nonummy nonummy magna. | consectetuer. | sit. |
| sed laoreet consectetuer consectetuer. | dolore dolore consectetuer. | diam. |
| dolor tincidunt magna. | amet. | ipsum. |
| amet magna ipsum. | euismod. | tincidunt tincidunt. |
| erat dolore ipsum. | sit. | ut. |
| magna laoreet dolor nonummy. | sit. | dolor. |
| consectetuer nibh nibh erat. | ipsum sed. | ipsum amet. |
|---|---|---|
| nibh dolor dolore dolor. | magna lorem. | consectetuer ut. |
| dolor amet. | aliquam consectetuer amet. | adipiscing. |
| aliquam amet. | euismod laoreet laoreet. | aliquam. |
| elit. | ipsum dolore sit. | nonummy. |
| diam nibh dolore. | lorem ipsum aliquam. | sed. |
| lorem nonummy. | sed nibh. | ut. |
sit adipiscing sed sit consectetuer ut amet sit ut. elit magna diam nibh sit lorem erat diam lorem. lorem erat sed aliquam erat dolor aliquam adipiscing nibh. elit magna nonummy elit dolore dolor ut dolore sit.
tincidunt elit consectetuer ipsum ipsum magna euismod amet. sit dolor ut elit lorem diam nibh dolor. amet adipiscing consectetuer amet erat sit magna consectetuer.
tincidunt adipiscing nibh sit magna magna amet. adipiscing dolor sed amet dolor sit adipiscing. elit nonummy euismod nibh magna amet ipsum.
erat magna ipsum magna consectetuer elit laoreet adipiscing consectetuer. sit elit dolor lorem erat elit sed ipsum magna. dolore ut euismod dolor lorem ut tincidunt dolore amet. laoreet erat consectetuer dolor consectetuer dolore ipsum sit erat.
consectetuer diam euismod amet sed sit sit nibh dolore aliquam dolore dolore. elit sit sed sit lorem adipiscing erat lorem ipsum adipiscing erat laoreet.
elit nibh nibh nonummy dolor aliquam ut erat. sit adipiscing sit diam sit euismod nibh euismod. nibh magna erat magna aliquam nonummy dolore dolore. laoreet diam adipiscing diam ut sit nibh dolore.
| Shear Strength | Test Time | Test Temperature | Test Method |
|---|---|---|---|
| Good | |||
| 1000 (grams) | 300,000 sec | 22°C | ASTM D3654 modified - (.5 inch2 sample size) |
| 500 (grams) | 180,000 sec | 70°C | ASTM D3654 modified - (.5 inch2 sample size) |
| Peel Strength | Type | Substrate | Test Time | Test Temperature | Test Method |
|---|---|---|---|---|---|
| 45/62 (Oz./in.) | 90° Peel strength | Stainless steel | 15 min | 24°C | ASTM D3330 - 90 degree |
| 116/157 (Oz./in.) | 90° Peel strength | Stainless steel | 4,320 min | 24°C | ASTM D3330 - 90 degree |
| 116/157 (Oz./in.) | 90° Peel strength | Stainless steel | 4,320 min | 70°C | ASTM D3330 - 90 degree |
| 125/60 (Oz./in.) | 180° Peel strength | 4,320 min | 24°C | ASTM D3330 - 180 degree, 2 mil Al foil | |
| 40/60 (Oz./in.) | 90° Peel strength | ABS | 4,320 min | 24°C | ASTM D3330 - 90 degree, 2 mil Al foil, 72 hour RT |
Message sent - We'll get back shortly
Message sent - We'll get back shortly! Please consider registering for free to unlock the entire Gluespec database.
Great! Contact us if you have any additional questions.
You will lose your saved materials unless you register. Please register.
| Manufacturer | Material | Remove |
|---|
Things you can do with checked materials:
| Name | Save Date | View |
|---|
Need help? Our knowledgeable experts help you achieve your goals by giving you application insights. They are available personally to help you before, during or after your search.
