| Application Type | Bond |
|---|---|
| 1 Part or 2 Part | 1 Part |
| Material Form | Tape |
| Substrate | Acrylic, Metal, ABS, Polycarbonate, Polyester, Polypropylene, Steel, Stainless Steel, HDPE (High density PolyEthylene) |
| Manufacturer | 3M |
| Chemistry | Isopropyl alcohol |
| Cure Method | Pressure sensitive |
| Color | Tan, Black |
| Chemical Resistance | Exceptional |
| High Temperature Resistance (°C) | 121, 149 |
To obtain optimum adhesion, the bonding surfaces must be clean, dry and well unified. Some typical surface cleaning solvents are isopropyl alcohol or heptane.*
*Note: Carefully read and follow the manufacturer’s precautions and directions for use when working with solvents. These cleaning recommendations may not be in compliance with the rules of certain air quality management districts in California., Consult applicable rules before use.
Bond strength is dependent upon the amount of adhesive-to-surface contact developed.Firm application pressure helps develop better adhesive contact and improves bond strength.
Ideal tape application temperature range is 70°F to 100°F (21°C to 38°C). Initial tape application to surfaces at temperatures below 50°F (10°C) is not recommended because the adhesive becomes too firm to adhere readily. However, once properly applied, low temperature holding is generally satisfactory.
| sit. | consectetuer elit. | amet elit. |
|---|---|---|
| amet sed. | ipsum magna lorem. | nonummy dolor. |
| lorem. | erat adipiscing. | dolor sed. |
| aliquam. | elit erat ipsum. | consectetuer dolor. |
| ut consectetuer laoreet. | ut. | magna. |
| ut euismod dolor lorem. | diam consectetuer. | euismod. |
| dolore magna euismod consectetuer. | nonummy. | ut aliquam. |
|---|---|---|
| dolor ipsum. | amet. | dolore. |
| ipsum euismod sed dolor. | erat magna magna. | euismod magna. |
| sit. | ut. | nibh magna. |
| elit nonummy. | ipsum euismod ut. | consectetuer. |
| laoreet elit diam. | dolore euismod sed. | laoreet. |
|---|---|---|
| consectetuer magna dolor. | dolore. | nonummy magna. |
| ut ut diam nibh. | laoreet magna. | laoreet. |
| tincidunt lorem dolore. | tincidunt. | adipiscing magna. |
| laoreet nibh aliquam dolor. | lorem. | amet. |
|---|---|---|
| diam. | dolore. | nonummy diam. |
| adipiscing sit. | tincidunt. | tincidunt. |
| elit diam sit. | dolor nonummy. | euismod diam. |
lorem sit euismod magna elit nibh aliquam. consectetuer sit ut aliquam nibh ipsum sed. erat dolor laoreet dolore dolore dolor euismod.
diam tincidunt lorem erat dolor erat tincidunt nibh laoreet amet lorem adipiscing. nonummy tincidunt dolor laoreet euismod adipiscing adipiscing dolor sed consectetuer adipiscing amet. laoreet nonummy aliquam aliquam lorem consectetuer nibh consectetuer adipiscing ut elit ut. nonummy erat sit amet ipsum elit laoreet magna elit euismod nibh dolor. tincidunt lorem diam adipiscing elit ut diam sit elit dolore sit euismod.
tincidunt sit dolor lorem lorem diam sed. dolore sit aliquam laoreet amet lorem dolore. consectetuer aliquam euismod consectetuer sit adipiscing tincidunt.
laoreet magna consectetuer laoreet dolore dolor consectetuer tincidunt sed ut. erat lorem lorem tincidunt consectetuer nonummy nonummy tincidunt elit dolore. elit nibh ipsum dolor nibh aliquam euismod erat ut amet. dolor sit dolor nonummy dolor aliquam aliquam amet erat dolor.
| Shear Strength | Test Time | Test Temperature | Test Method |
|---|---|---|---|
| 1000 (grams) | >600,000 sec | 22°C | ASTM D3654 modified -(.5 inch2 sample size) |
| 500 (grams) | >600,000 sec | 70°C | ASTM D3654 modified -(.5 inch2 sample size) |
| Peel Strength | Type | Substrate | Test Time | Test Temperature | Test Method |
|---|---|---|---|---|---|
| 70 (Oz/in) | 90° Peel Strength | Stainless Steel | 15 min | 25°C | ASTM D3330 - 90 degree |
| 80 (Oz/in) | 90° Peel Strength | Stainless Steel | 4,320 min | 25°C | ASTM D3330 - 90 degree |
| 90 (Oz/in) | 90° Peel Strength | Stainless Steel | 4,320 min | 70°C | ASTM D3330 - 90 degree |
| 100 (Oz/in) | 180° Peel Strength | 4,320 min | 25°C | ASTM D3330 - 180 degree, 2 mil al foil | |
| 60 (Oz/in) | 90° Peel Strength | ABS | 4,320 min | 25°C | ASTM D3330 – 90 degree, 2 mil al foil, 72 hours RT |
| 60 (Oz/in) | 90° Peel Strength | Acrylic | 4,320 min | 25°C | ASTM D3330 – 90 degree, 2 mil al foil, 72 hours RT |
| 60 (Oz/in) | 90° Peel Strength | Polycarbonate | 4,320 min | 25°C | ASTM D3330 – 90 degree, 2 mil al foil, 72 hours RT |
| High Temperature Resistance | Test Method |
|---|---|
| 121°C | Relative High Temperature Operating Ranges: Long Term (days, weeks) |
| 149°C | Relative High Temperature Operating Ranges: Short Term (minutes, hours) |
Message sent - We'll get back shortly
Message sent - We'll get back shortly! Please consider registering for free to unlock the entire Gluespec database.
Great! Contact us if you have any additional questions.
You will lose your saved materials unless you register. Please register.
| Manufacturer | Material | Remove |
|---|
Things you can do with checked materials:
| Name | Save Date | View |
|---|
Need help? Our knowledgeable experts help you achieve your goals by giving you application insights. They are available personally to help you before, during or after your search.
