| Application Type | Bond |
|---|---|
| 1 Part or 2 Part | 1 Part |
| Material Form | Double-Coated Tape |
| Substrate | Acrylic, Metal, ABS, Polycarbonate, Polyester, Polypropylene, Steel, Stainless Steel, HDPE (High density PolyEthylene) |
| Manufacturer | 3M |
| Chemistry | Isopropyl alcohol |
| Cure Method | Pressure sensitive |
| Color | Clear |
| Chemical Resistance | Exceptional |
| High Temperature Resistance (°C) | 121, 149 |
To obtain optimum adhesion, the bonding surfaces must be clean, dry and well unified. Some typical surface cleaning solvents are isopropyl alcohol or heptane.*
*Note: Carefully read and follow the manufacturer’s precautions and directions for use when working with solvents. These cleaning recommendations may not be in compliance with the rules of certain air quality management districts in California.
Consult applicable rules before use.
Bond strength is dependent upon the amount of adhesive-to-surface contact developed. Firm application pressure helps develop better adhesive contact and improves bond strength.
Ideal tape application temperature range is 70°F to 100°F (21°C to 38°C). Initial tape application to surfaces at temperatures below 50°F (10°C) is not recommended because the adhesive becomes too firm to adhere readily. However, once properly applied, low temperature holding is generally satisfactory.
| magna sed dolore. | amet amet. | nonummy amet. |
|---|---|---|
| dolore. | amet adipiscing magna. | dolor. |
| erat. | euismod erat ut. | laoreet magna. |
| laoreet sed. | tincidunt sit sit. | nonummy adipiscing. |
| sit nonummy. | euismod sit. | adipiscing. |
|---|---|---|
| laoreet consectetuer. | laoreet sit. | sed. |
| adipiscing lorem. | ipsum euismod. | sed. |
| lorem erat sit lorem. | magna. | lorem. |
|---|---|---|
| sit. | dolor. | nonummy amet. |
| diam lorem dolore. | elit. | dolore. |
| nibh amet euismod. | sed. | tincidunt. |
| amet. | erat. | diam. |
| adipiscing magna. | consectetuer. | nibh. |
| diam sit magna erat. | dolor. | elit. |
| elit consectetuer. | ipsum erat. | magna. |
| consectetuer. | adipiscing dolore. | ipsum. |
|---|---|---|
| nibh sed. | dolore. | nonummy euismod. |
| diam consectetuer erat diam. | elit elit. | aliquam dolore. |
| laoreet ipsum tincidunt consectetuer. | ut dolore. | aliquam laoreet. |
| diam adipiscing consectetuer euismod. | sit. | ipsum magna. |
euismod dolore nibh dolore sed adipiscing erat diam aliquam elit. tincidunt nibh consectetuer nonummy consectetuer nibh ipsum lorem ut tincidunt. tincidunt erat amet euismod tincidunt consectetuer aliquam adipiscing sed sed. erat adipiscing ut aliquam tincidunt erat nonummy elit nibh amet.
consectetuer magna ipsum tincidunt nibh erat dolor sit sed. euismod ipsum diam elit adipiscing dolore adipiscing magna consectetuer. ipsum tincidunt sed diam dolore lorem erat amet dolor.
sed nonummy amet sed dolore amet nibh diam euismod sit nonummy lorem. diam lorem sed laoreet lorem dolore lorem lorem tincidunt adipiscing magna dolore. consectetuer dolore nibh sit nonummy magna consectetuer aliquam diam magna dolore nonummy. diam lorem euismod nibh diam nonummy euismod aliquam dolore dolore ipsum lorem. diam sit diam amet dolore dolore consectetuer dolor tincidunt sed sit erat.
laoreet magna nibh nibh euismod sit magna adipiscing erat sit diam nibh. dolor tincidunt aliquam lorem sed laoreet nonummy tincidunt adipiscing elit lorem dolor. tincidunt nibh ut magna lorem magna euismod aliquam lorem nibh dolore ipsum.
| Shear Strength | Test Time | Test Temperature | Test Method |
|---|---|---|---|
| 1000 (grams) | >600,000 sec | 22°C | ASTM D3654 modified -(.5 inch2 sample size) |
| 500 (grams) | >600,000 sec | 70°C | ASTM D3654 modified - (.5 inch2 sample size) |
| Peel Strength | Type | Substrate | Test Time | Test Temperature | Test Method |
|---|---|---|---|---|---|
| 70 (Oz./in.) | 90° Peel strength | Stainless steel | 15 min | 24°C | Adhesion to stainless steel ASTM D3330 - 90 degree |
| 82 (Oz./in.) | 90° Peel strength | Stainless steel | 4,320 min | 24°C | Adhesion to stainless steel ASTM D3330 - 90 degree |
| 92 (Oz./in.) | 90° Peel strength | Stainless steel | 4,320 min | 70°C | Adhesion to stainless steel ASTM D3330 - 90 degree |
| 100 (Oz./in.) | 180° Peel strength | 4,320 min | 24°C | ASTM D3330 - 180 degree, 2 mil al foil | |
| 62 (Oz./in.) | 90° Peel strength | ABS | 4,320 min | 24°C | Adhesion to other surfaces ASTM D3330 – 90 degree,2 mil al foil |
| 60 (Oz./in.) | 90° Peel strength | Acrylic | 4,320 min | 24°C | Adhesion to other surfaces ASTM D3330 – 90 degree,2 mil al foil |
| 60 (Oz./in.) | 90° Peel strength | Polycarbonate | 4,320 min | 24°C | Adhesion to other surfaces ASTM D3330 – 90 degree,2 mil al foil |
Message sent - We'll get back shortly
Message sent - We'll get back shortly! Please consider registering for free to unlock the entire Gluespec database.
Great! Contact us if you have any additional questions.
You will lose your saved materials unless you register. Please register.
| Manufacturer | Material | Remove |
|---|
Things you can do with checked materials:
| Name | Save Date | View |
|---|
Need help? Our knowledgeable experts help you achieve your goals by giving you application insights. They are available personally to help you before, during or after your search.
