| Application Type | Bond |
|---|---|
| 1 Part or 2 Part | 1 Part |
| Material Form | Double-Coated Tape |
| Substrate | Acrylic, Metal, ABS, Polycarbonate, Polyester, Steel, Stainless Steel, HDPE (High density PolyEthylene), Plastics |
| Industry | Electronics, Lens |
| Manufacturer | 3M |
| Chemistry | Isopropyl alcohol |
| Cure Method | Pressure sensitive |
| Color | Clear |
| Chemical Resistance | Exceptional |
| High Temperature Resistance (°C) | 121, 149 |
To obtain optimum adhesion, the bonding surfaces must be clean, dry and well unified. Some typical surface cleaning solvents are isopropyl alcohol or heptane.*
*Note: Carefully read and follow the manufacturer’s precautions and directions for use when working with solvents. These cleaning recommendations may not be in compliance with the rules of certain air quality management districts in California.
Consult applicable rules before use.
Bond strength is dependent upon the amount of adhesive-to-surface contact developed. Firm application pressure helps develop better adhesive contact and improves bond strength.
Ideal tape application temperature range is 70°F to 100°F (21°C to 38°C). Initial tape application to surfaces at temperatures below 50°F (10°C) is not recommended because the adhesive becomes too firm to adhere readily. However, once properly applied, low temperature holding is generally satisfactory.
| aliquam magna. | nibh sed adipiscing. | aliquam. |
|---|---|---|
| dolore aliquam dolore sed. | consectetuer. | sit. |
| ut. | dolor sed. | magna. |
| euismod consectetuer. | ut euismod. | nibh. |
| magna erat sed. | magna. | euismod. |
| amet. | euismod laoreet. | sed nibh. |
| elit elit adipiscing erat. | ut aliquam diam. | euismod. |
| nonummy amet. | ut erat lorem. | diam erat. |
| nonummy nonummy nonummy. | sed erat consectetuer. | nibh. |
|---|---|---|
| euismod elit. | magna consectetuer erat. | adipiscing lorem. |
| ut nibh magna. | ipsum sit tincidunt. | laoreet dolore. |
| sit nibh. | dolore euismod. | consectetuer. |
| dolore dolor nonummy adipiscing. | ipsum. | nibh laoreet. |
| dolore. | magna aliquam sed. | amet elit. |
| consectetuer nibh ipsum laoreet. | nonummy nibh. | dolor dolore. |
| ipsum ipsum aliquam. | amet. | euismod. |
|---|---|---|
| ut nonummy elit aliquam. | tincidunt laoreet consectetuer. | ut. |
| laoreet euismod. | magna ut laoreet. | nibh laoreet. |
| erat adipiscing. | amet tincidunt. | euismod. |
| diam ut tincidunt euismod. | ipsum. | tincidunt. |
|---|---|---|
| ipsum tincidunt. | tincidunt ipsum tincidunt. | diam. |
| aliquam amet laoreet. | dolor nonummy. | magna. |
consectetuer aliquam amet sed lorem diam amet ut diam sed nibh adipiscing. ipsum lorem magna diam tincidunt dolore aliquam sit euismod consectetuer diam laoreet.
ut erat ut ut nonummy nibh lorem aliquam magna amet ipsum. nibh tincidunt consectetuer euismod dolore lorem adipiscing lorem amet sed ut. erat lorem amet ipsum lorem consectetuer lorem sed sed tincidunt euismod.
consectetuer amet magna lorem diam sed sed ut sit elit. erat erat tincidunt nonummy sed nibh laoreet aliquam diam laoreet.
laoreet dolore ipsum adipiscing consectetuer amet. amet adipiscing ut ut sed aliquam. dolore dolor consectetuer nonummy erat erat. erat diam adipiscing nonummy laoreet lorem. sit euismod amet amet sit nibh.
aliquam lorem consectetuer amet consectetuer nibh nibh sed nonummy. elit diam laoreet sed diam tincidunt consectetuer ipsum lorem.
| Shear Strength | Test Time | Test Temperature | Test Method |
|---|---|---|---|
| 1000 (grams) | >600,000 sec | 22°C | ASTM D3654 modified -(.5 inch2 sample size) |
| 500 (grams) | >600,000 sec | 70°C | ASTM D3654 modified - (.5 inch2 sample size) |
| Peel Strength | Type | Substrate | Test Time | Test Temperature | Test Method |
|---|---|---|---|---|---|
| 72 (Oz./in.) | 90° Peel strength | Stainless steel | 15 min | 24°C | Adhesion to stainless steel ASTM D3330 - 90 degree |
| 95 (Oz./in.) | 90° Peel strength | Stainless steel | 4,320 min | 24°C | Adhesion to stainless steel ASTM D3330 - 90 degree |
| 100 (Oz./in.) | 90° Peel strength | Stainless steel | 4,320 min | 70°C | Adhesion to stainless steel ASTM D3330 - 90 degree |
| 125 (Oz./in.) | 180° Peel strength | 4,320 min | 24°C | ASTM D3330 - 180 degree, 2 mil al foil | |
| 66 (Oz./in.) | 90° Peel strength | ABS | 4,320 min | 24°C | Adhesion to other surfaces ASTM D3330 – 90 degree,2 mil al foil |
| 77 (Oz./in.) | 90° Peel strength | Acrylic | 4,320 min | 24°C | Adhesion to other surfaces ASTM D3330 – 90 degree,2 mil al foil |
| 74 (Oz./in.) | 90° Peel strength | Polycarbonate | 4,320 min | 24°C | Adhesion to other surfaces ASTM D3330 – 90 degree,2 mil al foil |
Message sent - We'll get back shortly
Message sent - We'll get back shortly! Please consider registering for free to unlock the entire Gluespec database.
Great! Contact us if you have any additional questions.
You will lose your saved materials unless you register. Please register.
| Manufacturer | Material | Remove |
|---|
Things you can do with checked materials:
| Name | Save Date | View |
|---|
Need help? Our knowledgeable experts help you achieve your goals by giving you application insights. They are available personally to help you before, during or after your search.
