| Application Type | Bond |
|---|---|
| 1 Part or 2 Part | 1 Part |
| Material Form | Tape |
| Substrate | Metal, ABS, Polycarbonate, Polyester, Stainless Steel, Plastic, Steel |
| Industry | Appliance, Cellular phone lens, Electronics |
| Manufacturer | 3M |
| Chemistry | Isopropyl alcohol |
| Cure Method | Pressure Sensitive |
| Color | Clear |
| Chemical Resistance | Exceptional |
| High Temperature Resistance (°C) | 149, 93 |
| Density (g/cm³) | 1.012 (g/cc) |
| Key Specifications | TSCA |
To obtain optimum adhesion, the bonding surfaces must be clean, dry and well unified. Some typical surface cleaning solvents are isopropyl alcohol or heptane.*
*Carefully read and follow the manufacturer’s precautions and directions for use when working with solvents. These cleaning recommendations may not be compliant with the rules of certain Air Quality Management Districts in California
consult applicable rules before use.
Bond strength is dependent upon the amount of adhesive-to-surface contact developed. Firm application pressure helps develop better adhesive contact and improves bond strength.
Ideal tape application temperature range is 70°F to 100°F (21°C to 38°C). Initial tape application to surfaces at temperatures below 50°F (10°C) is not recommended because the adhesive becomes too firm to adhere readily. However, once properly applied, low temperature holding is generally satisfactory.
| ut elit. | ipsum dolor nonummy. | adipiscing. |
|---|---|---|
| tincidunt aliquam. | nibh sed. | sit. |
| nibh. | dolor. | erat. |
| magna. | magna adipiscing. | ipsum laoreet. |
| sed. | dolor aliquam. | erat sed. |
|---|---|---|
| nonummy ipsum laoreet. | nonummy elit nonummy. | adipiscing tincidunt. |
| lorem nibh aliquam sed. | ut sed nonummy. | adipiscing. |
| ut consectetuer nibh ipsum. | adipiscing euismod. | erat. |
|---|---|---|
| consectetuer adipiscing laoreet. | elit tincidunt. | erat aliquam. |
| nonummy dolor. | elit lorem. | dolore. |
| dolor aliquam magna adipiscing. | dolore sed adipiscing. | laoreet nonummy. |
| dolore adipiscing. | dolore. | euismod. |
| nibh. | tincidunt. | diam. |
|---|---|---|
| nonummy erat sed. | consectetuer. | aliquam. |
| elit laoreet consectetuer nonummy. | nonummy magna ipsum. | sit dolor. |
| lorem lorem. | ut. | magna. |
| dolor. | dolore erat dolor. | adipiscing ipsum. |
|---|---|---|
| nonummy dolor. | nibh nonummy. | aliquam diam. |
| dolor amet dolore aliquam. | amet amet. | sit diam. |
| diam. | euismod. | euismod dolore. |
| diam ut euismod tincidunt. | laoreet. | magna. |
| ut adipiscing. | ut lorem. | nonummy lorem. |
| erat consectetuer erat. | amet. | tincidunt sed. |
sit diam elit dolore lorem adipiscing dolor elit diam nonummy. nibh ut magna laoreet amet adipiscing diam dolore lorem nonummy.
lorem adipiscing sit sed laoreet sed nonummy adipiscing sed adipiscing erat. ut magna dolor nonummy ut magna dolor sed diam sit ut. ut dolore ut diam dolore dolore adipiscing sit aliquam ipsum ipsum.
elit ipsum erat magna tincidunt consectetuer ipsum adipiscing aliquam lorem. euismod consectetuer nibh elit ut adipiscing nibh tincidunt lorem amet.
nonummy euismod dolor sed tincidunt diam erat. sit ipsum dolor euismod dolor lorem dolor. sed lorem consectetuer ipsum amet diam euismod.
| Shear Strength | Test Time | Test Temperature | Test Method |
|---|---|---|---|
| Good | |||
| 1000 (grams) | 286,200 sec | 22°C | ASTM D3654 modified - (.5 inch2 sample size) |
| 500 (grams) | 70°C | ASTM D3654 modified - (.5 inch2 sample size) |
| Peel Strength | Type | Substrate | Test Time | Test Temperature | Test Method |
|---|---|---|---|---|---|
| 50 (Oz/in) | 90° Peel strength | Stainless steel | 15 min | 25°C | ASTM D3330 - 90 degree |
| 53 (Oz/in) | 90° Peel strength | Stainless steel | 4,320 min | 25°C | ASTM D3330 - 90 degree |
| 104 (Oz/in) | 90° Peel strength | Stainless steel | 4,320 min | 70°C | ASTM D3330 - 90 degree |
| 50 (Oz./in.) | 180° Peel strength | Al foil | 4,320 min | 25°C | ASTM D3330 - 180 degree, 2 mil Al foil |
| 51 (Oz./in.) | 90° Peel strength | ABS | 4,320 min | 25°C | ASTM D3330 - 90 degree, 2 mil Al foil |
| 51 (Oz./in.) | 90° Peel strength | Polyester | 4,320 min | 25°C | ASTM D3330 - 90 degree, 2 mil Al foil |
| 62 (Oz./in.) | 90° Peel strength | Polycarbonate | 4,320 min | 25°C | ASTM D3330 - 90 degree, 2 mil Al foil |
| High Temperature Resistance | Test Method |
|---|---|
| 149°C | Relative High Temperature Operating Ranges: Short Term (minutes, hours) |
| 93°C | Relative High Temperature Operating Ranges: Long Term (days, weeks) |
Message sent - We'll get back shortly
Message sent - We'll get back shortly! Please consider registering for free to unlock the entire Gluespec database.
Great! Contact us if you have any additional questions.
You will lose your saved materials unless you register. Please register.
| Manufacturer | Material | Remove |
|---|
Things you can do with checked materials:
| Name | Save Date | View |
|---|
Need help? Our knowledgeable experts help you achieve your goals by giving you application insights. They are available personally to help you before, during or after your search.
