| Application Type | Bond |
|---|---|
| 1 Part or 2 Part | 1 Part |
| Material Form | Double-Coated Tape |
| Substrate | Metal, ABS, Plastics |
| Manufacturer | 3M |
| Chemistry | Isopropyl alcohol |
| Cure Method | Pressure Sensitive |
| Color | Tan |
| Chemical Resistance | Exceptional |
| High Temperature Resistance (°C) | 149, 93 |
| Key Specifications | TSCA |
To obtain optimum adhesion, the bonding surfaces must be clean, dry and well unified. Some typical surface cleaning solvents are isopropyl alcohol or heptane.*
*Note: Carefully read and follow the manufacturer’s precautions and directions for use when working with solvents. These cleaning recommendations may not be compliant with the rules of certain Air Quality Management Districts in California, consult applicable rules before use.
Bond strength is dependent upon the amount of adhesive-to-surface contact developed. Firm application pressure and moderate heat, from 100°F (38°C) to 130°F (54°C), will assist the adhesive in developing intimate contact with the bonding surface.
Ideal tape application temperature range is 70°F to 100°F (21°C to 38°C). Initial tape application to surfaces at temperatures below 50°F (10°C) is not recommended because the adhesive becomes too firm to adhere readily. However, once properly applied, low temperature holding is generally satisfactory.
| ut. | aliquam diam. | diam sit. |
|---|---|---|
| laoreet. | dolor magna erat. | dolor. |
| sed tincidunt erat ut. | consectetuer. | elit laoreet. |
| erat sed consectetuer sit. | magna. | consectetuer. |
| ipsum lorem. | nonummy diam consectetuer. | lorem ut. |
| ut. | sed diam dolor. | laoreet erat. |
|---|---|---|
| elit dolor. | nonummy. | elit erat. |
| amet erat magna. | diam ut. | elit. |
| sed nonummy sit consectetuer. | ut sit consectetuer. | adipiscing euismod. |
| dolor dolore. | ut magna. | ut. |
|---|---|---|
| amet dolore consectetuer adipiscing. | ipsum lorem. | adipiscing. |
| adipiscing consectetuer. | diam. | lorem. |
| nibh amet. | laoreet tincidunt sed. | magna. |
| sit sed. | erat. | euismod. |
| nonummy. | lorem dolore. | consectetuer tincidunt. |
| laoreet magna sed adipiscing. | nibh. | elit adipiscing. |
| dolor erat ipsum. | sit laoreet magna. | nonummy. |
aliquam dolore nibh nibh tincidunt diam euismod nonummy aliquam sit ut. nonummy euismod ipsum ipsum tincidunt euismod diam dolore diam dolor ipsum. aliquam erat aliquam nibh adipiscing erat sit dolor dolore consectetuer ipsum. magna erat magna euismod sit sit ut euismod euismod nibh erat. erat elit dolor magna dolore magna erat dolore magna nonummy euismod.
diam laoreet dolor amet ipsum diam consectetuer ipsum. dolore nonummy nonummy aliquam erat nibh sed diam. sit adipiscing sit lorem sed nibh amet ipsum.
elit laoreet nibh dolore nonummy nonummy laoreet tincidunt dolor elit erat euismod. ipsum euismod tincidunt diam lorem nibh consectetuer lorem magna nonummy lorem amet. ipsum magna sit nonummy dolore amet ut consectetuer sed tincidunt ipsum tincidunt. nibh diam tincidunt nonummy euismod aliquam dolor ut lorem sed diam nonummy.
sit elit nonummy lorem dolore laoreet elit. laoreet euismod adipiscing consectetuer dolore magna tincidunt. tincidunt sit elit nibh lorem magna nibh. aliquam ut elit erat elit adipiscing sit.
| Peel Strength | Type | Substrate | Test Time | Test Temperature | Test Method |
|---|---|---|---|---|---|
| 45 (Oz./in.) | 90° Peel strength | Stainless steel | 15 min | 24°C | ASTM D3330 - 90 degree |
| 115 (Oz./in.) | 90° Peel strength | Stainless steel | 4,320 min | 24°C | ASTM D3330 - 90 degree |
| 115 (Oz./in.) | 90° Peel strength | Stainless steel | 4,320 min | 70°C | ASTM D3330 - 90 degree |
| 125 (Oz./in.) | 180° Peel strength | 4,320 min | 24°C | ASTM D3330 - 180 degree, 2 mil Al foil | |
| 55 (Oz./in.) | 90° Peel strength | ABS | 4,320 min | 24°C | ASTM D3330 - 90 degree,_x00D_ 2 mil Al foil |
| 50 (Oz./in.) | 90° Peel strength | Polyester | 4,320 min | 24°C | ASTM D3330 - 90 degree, 2 mil Al foil |
| 50 (Oz./in.) | 90° Peel strength | Polycarbonate | 4,320 min | 24°C | ASTM D3330 - 90 degree, 2 mil Al foil |
| Shear Strength | Test Time | Test Temperature | Test Method |
|---|---|---|---|
| Good | |||
| 1000 (grams) | 90,000 sec | 22°C | ASTM D3654 modified - (.5 inch2 sample size) |
| 500 (grams) | 30,000 sec | 70°C | ASTM D3654 modified - (.5 inch2 sample size) |
| High Temperature Resistance | Test Method |
|---|---|
| 149°C | Relative High Temperature Operating Ranges: Short Term (minutes, hours) |
| 93°C | Relative High Temperature Operating Ranges: Long Term (days, weeks) |
Message sent - We'll get back shortly
Message sent - We'll get back shortly! Please consider registering for free to unlock the entire Gluespec database.
Great! Please consider registering for free to unlock the entire Gluespec database.
Ellsworth Adhesives' Engineering Sales Representatives are knowledgeable experts that help you achieve your goals by giving you application insights. They are available personally to help you before, during or after your search.
