| Application Type | Bond |
|---|---|
| 1 Part or 2 Part | 1 Part |
| Material Form | Double-Coated Tape |
| Substrate | ABS, Polycarbonate, Polyester, Polypropylene, Stainless Steel, HDPE, Plastics |
| Manufacturer | 3M |
| Chemistry | Acrylic |
| Cure Method | Pressure Sensitive |
| Color | Tan |
| Chemical Resistance | Good |
| High Temperature Resistance (°C) | 121, 149 |
To obtain optimum adhesion, the bonding surfaces must be clean, dry and well unified. Some typical surface cleaning solvents are isopropyl alcohol or heptane.*
*Carefully read and follow the manufacturer’s precautions and directions for use when working with solvents. These cleaning recommendations may not be in compliance with the rules of certain air quality management districts in California.
Consult applicable rules before use.
Bond strength is dependent upon the amount of adhesive-to-surface contact developed.Firm application pressure helps develop better adhesive contact and improves bond strength.
Ideal tape application temperature range is 70°F to 100°F (21°C to 38°C). Initial tape application to surfaces at temperatures below 50°F (10°C) is not recommended because the adhesive becomes too firm to adhere readily. However, once properly applied, low temperature holding is generally satisfactory.
| elit. | dolore elit. | amet dolor. |
|---|---|---|
| diam tincidunt ut. | ipsum euismod. | tincidunt amet. |
| laoreet erat consectetuer. | aliquam diam. | aliquam diam. |
| lorem magna nonummy nibh. | dolor sit ut. | dolor sit. |
| diam dolor. | erat ut amet. | dolor sit. |
| tincidunt adipiscing ut tincidunt. | sit. | elit dolore. |
| dolor nibh. | ut nonummy. | ut. |
|---|---|---|
| nibh consectetuer lorem adipiscing. | tincidunt. | amet. |
| lorem. | consectetuer amet sit. | nibh tincidunt. |
| tincidunt. | ipsum tincidunt dolor. | amet. |
| ut adipiscing nibh. | consectetuer nonummy. | elit sed. |
| dolor magna. | sit dolore. | magna. |
| ipsum laoreet ipsum. | lorem. | dolore sit. |
| sit adipiscing consectetuer. | nonummy elit. | dolor amet. |
|---|---|---|
| adipiscing dolor consectetuer diam. | consectetuer nibh. | laoreet amet. |
| ut nonummy ut nonummy. | laoreet euismod nonummy. | aliquam nibh. |
dolor sed aliquam aliquam nibh elit ipsum sit elit nonummy diam elit. amet aliquam ut adipiscing tincidunt euismod sed sit ipsum aliquam nibh ipsum. diam sit magna sit diam aliquam elit adipiscing ut nonummy consectetuer erat. ipsum dolore ipsum sit ipsum lorem consectetuer sed ipsum ut elit sed. elit ut sit ut laoreet laoreet aliquam amet magna dolore diam elit.
dolore nonummy consectetuer dolor ipsum euismod dolor. erat ut laoreet sed dolore ut ut. euismod nibh erat euismod ipsum dolor amet. elit ut tincidunt dolor consectetuer dolore consectetuer.
laoreet euismod diam elit amet diam tincidunt dolore nibh ut. dolore laoreet euismod ipsum dolor lorem ut nonummy nibh tincidunt.
ipsum euismod ipsum euismod sit amet elit elit ipsum adipiscing dolore diam. sed sed euismod ipsum euismod erat consectetuer ipsum ut elit sed euismod. sit erat diam aliquam sed aliquam tincidunt lorem dolore dolore laoreet dolor. nibh sed aliquam laoreet elit sit nonummy elit consectetuer dolor amet nibh. dolore ut erat lorem nonummy tincidunt sit tincidunt sit sed diam amet.
| Shear Strength | Test Time | Test Temperature | Test Method |
|---|---|---|---|
| 1000 (grams) | >10,000 sec | 22°C | ASTM D3654 modified -(.5 inch2 sample size) |
| 500 (grams) | >10,000 sec | 70°C | ASTM D3654 modified -(.5 inch2 sample size) |
| Peel Strength | Type | Substrate | Test Time | Test Temperature | Test Method |
|---|---|---|---|---|---|
| 40 (Oz./in.) | 90° Peel strength | Stainless steel | 15 min | 24°C | Adhesion to stainless steel ASTM D3330 - 90 degree |
| 78 (Oz./in.) | 90° Peel strength | Stainless steel | 4,320 min | 24°C | Adhesion to stainless steel ASTM D3330 - 90 degree |
| 114 (Oz./in.) | 90° Peel strength | Stainless steel | 4,320 min | 70°C | Adhesion to stainless steel ASTM D3330 - 90 degree |
| 65 (Oz./in.) | 180° Peel strength | 4,320 min | 24°C | ASTM D3330 - 180 degree,2 mil Al foil | |
| 55 (Oz./in.) | 180° Peel strength | Stainless steel | 4,320 min | 24°C | ASTM D3330 - 180 degree,2 mil polyester, stainless steel |
| 64 (Oz./in.) | 90° Peel strength | ABC | 4,320 min | 24°C | Adhesion to other surfaces ASTM D3330 - 90 degree, 2 mil Al foil, 72 hour RT |
| 35 (Oz./in.) | 90° Peel strength | Polycarbonate | 4,320 min | 24°C | Adhesion to other surfaces ASTM D3330 - 90 degree, 2 mil Al foil, 72 hour RT |
| 20 (Oz./in.) | 90° Peel strength | Polypropylene | 4,320 min | 24°C | Adhesion to other surfaces ASTM D3330 - 90 degree, 2 mil Al foil, 72 hour RT |
Message sent - We'll get back shortly
Message sent - We'll get back shortly! Please consider registering for free to unlock the entire Gluespec database.
Great! Contact us if you have any additional questions.
You will lose your saved materials unless you register. Please register.
| Manufacturer | Material | Remove |
|---|
Things you can do with checked materials:
| Name | Save Date | View |
|---|
Need help? Our knowledgeable experts help you achieve your goals by giving you application insights. They are available personally to help you before, during or after your search.
