3M 98NF Scotch-Weld Hi-Strength Non-Flammable Cylinder Spray Adhesive

3M 98NF Scotch-Weld Hi-Strength Non-Flammable Cylinder Spray Adhesive Datasheet
CONTACT REP

  • Description for 3M 98NF Scotch-Weld Hi-Strength Non-Flammable Cylinder Spray Adhesive

    Industrial grade, high performance bulk spray adhesives formulated for high strength and high heat resistant bonds.

    Note: This material has been discontinued. Please view the Comparable Materials tab or call us at (262) 293-7970 for additional help.

    *See Terms of Use Below

    Application Type Bond
    1 Part or 2 Part 1 Part
    Material Form Liquid, Synthetic Elastomer
    Substrate Acrylic, Aluminum, FRP (Fiber Reinforced Plastic), Fabrics, Glass, Metal, Heavy papers, Most plastics, Polypropylene, Wood, Polyethylene, Galvanized, Soft foams, ABS, Birch
    Industry Motor homes
    Manufacturer 3M
    Chemistry Synthetic Elastomer, HAPS-free
    Cure Method Solvent
    Cure Time (min) Fast
    Color Red, Translucent
    High Temperature Resistance (°C) High heat resistance
    Density (g/cm³) 10.4 (lbs/gal)

  • Technical Data for 3M 98NF Scotch-Weld Hi-Strength Non-Flammable Cylinder Spray Adhesive

    *See Terms of Use Below

    Overview
    • Application Type
    • 1 Part or 2 Part
      • 1 Part or 2 Part - 1 Part
    • Material Form
      • Elastomer - Synthetic Elastomer
      • Liquid
    • Substrate
    • Industry
      • Recreational Vehicles - Motor homes
      • Industrial
      • Furniture / Wood-Working - Woodworking and cabinetry, Countertops, Cabinets , Shelves, Furniture, Displays
      • Other - Carpet
    • Chemistry
    • Application Method
      • Dispenser - Applicator
      • Spray
    • Cure Method
      • Solvent
    • Color
      • Translucent
      • Red
    Specifications
    Cure Specs
    Cure Time (min) Fast
    Set Time (min) 1.00 to 2.00
    Work / Pot Time (min) 1.00 to 60
    Bond Strength
    General Bond Strength (psi) High
    Shear Strength (psi) 130, 82, 200, 115, 171, 75, 105, 52, 168, 66, 127, 115 Test Method
    Tensile Strength (psi) 30 (grams) Test Method
    Material Resistance
    High Temperature Resistance (°C) High heat resistance
    Moisture/Humidity Resistance High moisture resistance
    Other Properties
    % Solids (%) High, 21 Test Method
    Density (g/cm³) 10.4 (lbs/gal)
    Business Information
    Shelf Life Details Storage: Store product at 60°-80°F (16°-27°C) for maximum storage life. Higher temperatures reduce normal storage life. Lower temperatures may cause increased viscosity of a temporary nature. Rotate stock on a “first in-first out” basis.;When stored at the recommended conditions in the original, unopened container, this product has a shelf life of 15 months from date of shipment.
    Shelf Life Type From the date of shipment
    Shelf Life (mon) 15

  • Best Practices for 3M 98NF Scotch-Weld Hi-Strength Non-Flammable Cylinder Spray Adhesive

    *See Terms of Use Below

    1. Surface Preparation

      For best results, all surfaces to be bonded must be clean, dry and free from dirt, dust, oil, loose paint, wax or grease, etc.

    2. Application

      Slowly open the cylinder valve and inspect the connections for any leaks. Tighten if needed.

      Fully open the valve.

      Unscrew the trigger stop/adjusting nut away from the trigger 3-4 turns and spray a test pattern. For more adhesive output, continue to screw the nut away from the trigger. For less adhesive output, screw the nut back towards the trigger.

      Hold the applicator 3-10 inches away from the surface to be sprayed and apply a uniform coat of adhesive. (The smaller the spray pattern chosen in step 3, the closer the applicator gun will need to be to the surface and vice versa for larger patterns.)

      Apply 1-3 even coats of adhesive. (This will depend on the needed coverage for the bonding application.)

    3. Curing

      Allow adhesive to dry until tacky and then apply sufficient pressure to ensure complete contact.

    4. Clean-Up

      When using solvents, extinguish all ignition sources, including pilot lights, and follow the manufacturer’s precautions and directions for use.

    5. Testing

      Test the tackiness by gently touching the adhesive with your knuckle. If the adhesive transfers to your skin, it is too wet. If the adhesive is aggressively tacky and does not transfer to your skin, it is ready to bond. If the adhesive is too dry or only has a very light tack, it is too dry and another coat of adhesive should be applied to at least one of the surfaces

    6. Troubleshooting

      How to Eliminate Cold Weather Problems:1.) Store the cylinders in a controlled environment with temperatures between 60°-80°F (16°-27°C)

      2.) Keep cylinders off of cold concrete floors and away from outside walls

      3.) Use heat belts or blankets, approved for use with flammable adhesives, to control the temperature of the cylinders.

      4.) Allow additional time for solvents and propellants to flash off, when temperatures are below 60°F (16°C).

      If the system sprays poorly or won’t spray at all: The sequence below runs through a complete clog into the cylinder valve. If at any time during the sequence the problem is resolved, stop, clean the needed parts, put the system back together, and you are finished.

      1. Make sure the cylinder is not empty.

      2. Make sure the cylinder valve is open.

      3. Close the applicator trigger stop adjusting nut and clean the nozzle tip. (Does it spray now?)

      4. Take off the nozzle and try spraying. (Does it spray now?) Clean the nozzle.

      5. Shut off the cylinder valve, CAREFULLY and SLOWLY – loosen the applicator gun/hose connection and look for adhesive to squirt out. If adhesive starts to leak out, allow it to slowly continue to do so until it stops. (This will be a little messy, but you will need to bleed off the pressurized adhesive to clean the applicator gun.) The applicator gun has a clog at the valve, stem or inlet area and needs to be cleaned.

      6. If nothing leaks out after fully loosening the applicator gun, CAREFULLY remove applicator gun, realizing that the hose may be clogged but could be full of adhesive and pressure depending on where the clog is. (Secure the open end of the hose into a bucket in case the clog releases and the system flushes.)

      7. CAREFULLY and SLOWLY loosen the hose connection at the cylinder valve. Look for adhesive to squirt out. If adhesive starts to leak out, allow it to slowly continue to do so until it stops. (This will be a little messy, but you will need to bleed off the pressurized adhesive in the hose). Clean or replace the hose.

      8. With everything now isolated from the cylinder, place a bucket in front of the cylinder valve and slowly open it to see if any adhesive comes out. If it does, put the cleaned system parts back together. If it does not, there is something wrong with the cylinder or cylinder valve and it should be returned.

  • Comparable Materials for 3M 98NF Scotch-Weld Hi-Strength Non-Flammable Cylinder Spray Adhesive

    *See Terms of Use Below

    Spec Engine® Results

    • Dow
      Dowsil 3140 RTV Coating(Dow)

      One-part, translucent adhesive or coating with good flowability, good flame resistance, UL, IPC and Mil spec tested.

    • 3M
      94CA(3M)

      • Postformable high strength • Low telegraphing spray pattern • SCAQMD Rule 1168 Compliant Contact Adhesive • Reduced open time

    • Compare All
  Download Technical Data Sheet   Save This Material Saved Items

Questions about this material?

3M - 98NF Scotch-Weld Hi-Strength Non-Flammable Cylinder Spray Adhesive

Get personal assistance with your specific application needs.

Your Profile Edit
Submit

Popular Articles

The difference between corona and plasma surface treatments

Read Article

Staking materials and properties

Read Article

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Read Article

Testing the effectiveness of surface treatments

Read Article

Sponsored Articles

Unique Advantages of Contact Adhesives

Read Article

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Read Article

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Read Article

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Read Article
Information provided by Gluespec

Why Register?

  • View Technical Details
  • View Test Methods
  • View Key Specifications
  • View Similar Materials
  • Save your Project Searches

Already registered? Sign in.

Questions? Learn more about Gluespec

Gluespec Poll

What level of expertise do you have in specialty chemicals like adhesives, sealants, conformal coatings, etc.?
Tensile Strength Test Methods
Tensile Strength Cure Time Test Temperature Test Method
30 (grams) 10 min -12°C 2 square inch bonds tested with 30 grams hanging in tensile. Temperature is held for 10 minutes and ramped at 10°F increments, until complete failure.
Shear Strength Test Methods
Shear Strength Type Substrate Test Temperature Test Method
130 psi Overlap Shear Strength ABS to ABS (2 surface adhesive bond 24°C 1 square inch bonds tested at 2 inches per minute separation rate at 75°F (24°).
82 psi Overlap Shear Strength ABS to ABS (1 surface adhesive bond) 24°C 1 square inch bonds tested at 2 inches per minute separation rate at 75°F (24°).
200 psi Overlap Shear Strength Acrylic to Acrylic (2 surface adhesive bond) 24°C 1 square inch bonds tested at 2 inches per minute separation rate at 75°F (24°).
115 psi Overlap Shear Strength Aluminum to Aluminum (2 surface adhesive bond) 24°C 1 square inch bonds tested at 2 inches per minute separation rate at 75°F (24°).
171 psi Overlap Shear Strength Birch to Birch (2 surface adhesive bond) 24°C 1 square inch bonds tested at 2 inches per minute separation rate at 75°F (24°).
75 psi Overlap Shear Strength Birch to Birch (1 surface adhesive bond) 24°C 1 square inch bonds tested at 2 inches per minute separation rate at 75°F (24°).
105 psi Overlap Shear Strength Galvanized to Galvanized (2 surface adhesive bond) 24°C 1 square inch bonds tested at 2 inches per minute separation rate at 75°F (24°).
52 psi Overlap Shear Strength Galvanized to Galvanized (1 surface adhesive bond) 24°C 1 square inch bonds tested at 2 inches per minute separation rate at 75°F (24°).
168 psi Overlap Shear Strength HPL to Particle Board (2 surface adhesive bond) 24°C 1 square inch bonds tested at 2 inches per minute separation rate at 75°F (24°).
66 psi Overlap Shear Strength Polyethylene to Polyethylene (2 surface adhesive bond) 24°C 1 square inch bonds tested at 2 inches per minute separation rate at 75°F (24°).
127 psi Overlap Shear Strength Polypropylene to Polypropylene (2 surface adhesive bond) 24°C 1 square inch bonds tested at 2 inches per minute separation rate at 75°F (24°).
115 psi Overlap Shear Strength FRP (Fiber Reinforced Plastic) to FRP (2 surface adhesive bond) 24°C 1 square inch bonds tested at 2 inches per minute separation rate at 75°F (24°).
% Solids Test Methods
% Solids Test Method
High
21 % By Wt.