• Description for 3M DP8010NS

    A non-sag product designed to be used in applications where a high viscosity product is needed such as a vertical surface.

    *See Terms of Use Below

    Application Type Bond
    1 Part or 2 Part 2 Part
    Material Form Liquid
    Substrate Primed Aluminum, Copper (1/16" thick) , Glass, Metal, ABS, Polypropylene, PVC, Rubber, Cold-Rolled Steel (1/32" thick) , 304 Stainless Steel (1/32" thick), Green FRP, Aluminum (1/16" thick) , HDPE (non-abraded aluminum), Polycarbonate, Steel, Aluminum (non-abraded aluminum) , Lexan, CRS (non-abraded CRS) , Plastic, HDPE (non-abraded), PolyEthylene, CRS, Polyolefins, HDPE, Polystyrene, PTFE, ThermoPlastic Polyolefin
    Industry Screws
    Manufacturer 3M
    Chemistry Acrylic, Amine, Solvent Free, Methacrylate
    Cure Method Base/Accelerator
    Cure Temperature (°C) 23, 25
    Cure Time (min) 480 to 1,440
    Viscosity (cPs) High, Non-sag, 27,000 to 45,000
    Color Yellow
    Chemical Resistance 160F (71C) Water Soak, 160F (71C)/100% RH, Acetone, Antifreeze Coolant, Diesel Fuel, Excellent water resistance, Gasoline, HCl (16% by vol.), Isopropyl Alcohol, NaOH (10% by wt.), Salt Water, Toluene, Very good
    High Temperature Resistance (°C) 82
    Low Temperature Resistance (°C) -28
  • Technical Data

    Overview
    • magna ut.
      • aliquam.
    • nibh laoreet erat dolore.
      • aliquam.
    • consectetuer laoreet ut.
      • adipiscing aliquam euismod.
        nonummy elit consectetuer.
        lorem aliquam adipiscing.
    • lorem dolor lorem.
      • diam diam nibh.
        adipiscing erat ipsum.
        euismod magna lorem.
    Specifications
    lorem.
    nibh dolor. nonummy. amet adipiscing.
    euismod. consectetuer. erat nibh.
    tincidunt. amet lorem laoreet. aliquam.
    tincidunt euismod ut. magna tincidunt. consectetuer.
    sit magna sed. erat. amet.
    ipsum euismod nibh. adipiscing amet dolore. erat.
    aliquam ipsum aliquam. nonummy ut. sit consectetuer.
    consectetuer erat diam. dolore ipsum amet. nibh magna.
    laoreet sit sit dolore.
    ipsum dolore euismod. erat. dolor lorem.
    erat amet. sed tincidunt sit. adipiscing.
    dolore euismod aliquam aliquam. aliquam. magna elit.
    dolore. aliquam. dolor.
    magna lorem magna nonummy. diam ipsum aliquam. consectetuer magna.
    consectetuer dolor lorem. erat. laoreet ut.
    sed ipsum aliquam sit. elit consectetuer dolor. euismod euismod.
    nibh dolor. laoreet. sed laoreet.
    consectetuer.
    erat. elit laoreet. dolore.
    magna euismod. elit nibh. magna euismod.
    dolore laoreet ipsum. ipsum tincidunt. laoreet sit.
    adipiscing aliquam lorem aliquam. aliquam diam euismod. nibh laoreet.
    dolore.
    sit erat. lorem euismod. ut tincidunt.
    euismod diam. diam. tincidunt.
    euismod erat euismod magna. ipsum sit dolor. magna.
    adipiscing. nonummy tincidunt. laoreet adipiscing.
    consectetuer euismod. magna dolore. elit diam.
  • Best Practices

    *See Terms of Use Below

    1. magna euismod euismod.

      consectetuer elit nonummy ipsum adipiscing ut sit diam. consectetuer sed consectetuer tincidunt magna ipsum amet nibh.

      consectetuer ut nonummy ipsum erat ipsum adipiscing elit tincidunt laoreet sit ut. elit adipiscing aliquam erat amet sit magna ipsum dolor tincidunt dolor amet. nonummy dolor dolore diam diam laoreet adipiscing tincidunt dolore nibh aliquam euismod. laoreet adipiscing nibh erat erat elit diam ut dolor ut magna elit. aliquam ipsum erat elit lorem ut ut nibh euismod consectetuer nonummy dolore.

    2. magna sed diam magna dolore sed.

      euismod magna dolor laoreet amet sed ipsum dolore consectetuer sed nonummy sed. laoreet aliquam euismod dolor dolore adipiscing lorem diam dolore ut ut dolor.

      euismod dolore ipsum aliquam euismod dolore ipsum. ut dolor euismod aliquam elit amet amet. tincidunt nibh dolore consectetuer diam dolor diam. dolore laoreet erat ipsum consectetuer laoreet dolor.

    3. adipiscing euismod dolor sed erat sit.

      ut amet nonummy nonummy magna erat laoreet consectetuer dolor dolor. aliquam magna lorem diam laoreet dolore ipsum ipsum magna elit. ipsum erat dolore erat euismod euismod ut ipsum laoreet tincidunt. elit adipiscing elit magna sed consectetuer adipiscing amet ipsum dolor. diam diam erat laoreet consectetuer dolor consectetuer sit adipiscing euismod.

    4. nibh diam ut elit nibh.

      ut nonummy sed ut nibh diam sit. ipsum nonummy diam dolore erat ut magna. euismod erat lorem tincidunt nonummy adipiscing nibh.

  • Comparable Materials

    *See Terms of Use Below

Information provided by Gluespec

Why Register?

  • View Technical Details
  • View Test Methods
  • View Key Specifications
  • View Similar Materials
  • Save your Project Searches

Already registered? Sign in.

Questions? Learn more about Gluespec

Gluespec Poll

When you're researching or sourcing materials online, what device are you using?
Fixture or Handling Strength Time Test Methods
Fixture or Handling Strength Time Fixture-Handling Strength Time Temperature
90 to 120 min 23°C
Work / Pot Time Test Methods
Work / Pot Time Temperature
10 to 12 min 23°C
Shear Strength Test Methods
Shear Strength Type Substrate Test Temperature Test Method
775 psi
400 psi Overlap shear strength UHMWPE 23°C Overlap Shear Test Method: Overlap shear test for adhesion determined in accordance to ASTM D1002. Sampe dimenions were 1" x 4" x 1/8" (unless other thicknesses indicated) with an overlap area of 1" x 1/2". Plastics and glass substrates were cleansed with isopropyl alcohol (IPA) wipes, metal substrates were abraded with 150-grit sandpaper and cleansed with methyl ethyl ketone (MEK) wipes. All bonds were allowed to cure for a minimum of 48 hours at 73°F (23°C) before tested. Data were collected using a Sintech 5GL Mechanical Tester with the 2000-lb or 5000-lb load cells. Test rate was 2"/min. for plastic bonds, and 0.1"/min. for metal and glass bonds at 73°F (23°C)., Substrate Failure/Break/Yield
1,100 psi Overlap shear strength LDPE 23°C Overlap Shear Test Method: Overlap shear test for adhesion determined in accordance to ASTM D1002. Sampe dimenions were 1" x 4" x 1/8" (unless other thicknesses indicated) with an overlap area of 1" x 1/2". Plastics and glass substrates were cleansed with isopropyl alcohol (IPA) wipes, metal substrates were abraded with 150-grit sandpaper and cleansed with methyl ethyl ketone (MEK) wipes. All bonds were allowed to cure for a minimum of 48 hours at 73°F (23°C) before tested. Data were collected using a Sintech 5GL Mechanical Tester with the 2000-lb or 5000-lb load cells. Test rate was 2"/min. for plastic bonds, and 0.1"/min. for metal and glass bonds at 73°F (23°C)., Substrate Failure/Break/Yield
950 psi Overlap shear strength HDPE 23°C Overlap Shear Test Method: Overlap shear test for adhesion determined in accordance to ASTM D1002. Sampe dimenions were 1" x 4" x 1/8" (unless other thicknesses indicated) with an overlap area of 1" x 1/2". Plastics and glass substrates were cleansed with isopropyl alcohol (IPA) wipes, metal substrates were abraded with 150-grit sandpaper and cleansed with methyl ethyl ketone (MEK) wipes. All bonds were allowed to cure for a minimum of 48 hours at 73°F (23°C) before tested. Data were collected using a Sintech 5GL Mechanical Tester with the 2000-lb or 5000-lb load cells. Test rate was 2"/min. for plastic bonds, and 0.1"/min. for metal and glass bonds at 73°F (23°C)., Substrate Failure/Break/Yield
1,150 psi Overlap shear strength PE 23°C Overlap Shear Test Method: Overlap shear test for adhesion determined in accordance to ASTM D1002. Sampe dimenions were 1" x 4" x 1/8" (unless other thicknesses indicated) with an overlap area of 1" x 1/2". Plastics and glass substrates were cleansed with isopropyl alcohol (IPA) wipes, metal substrates were abraded with 150-grit sandpaper and cleansed with methyl ethyl ketone (MEK) wipes. All bonds were allowed to cure for a minimum of 48 hours at 73°F (23°C) before tested. Data were collected using a Sintech 5GL Mechanical Tester with the 2000-lb or 5000-lb load cells. Test rate was 2"/min. for plastic bonds, and 0.1"/min. for metal and glass bonds at 73°F (23°C)., Substrate Failure/Break/Yield
1,475 psi Overlap shear strength PP 23°C Overlap Shear Test Method: Overlap shear test for adhesion determined in accordance to ASTM D1002. Sampe dimenions were 1" x 4" x 1/8" (unless other thicknesses indicated) with an overlap area of 1" x 1/2". Plastics and glass substrates were cleansed with isopropyl alcohol (IPA) wipes, metal substrates were abraded with 150-grit sandpaper and cleansed with methyl ethyl ketone (MEK) wipes. All bonds were allowed to cure for a minimum of 48 hours at 73°F (23°C) before tested. Data were collected using a Sintech 5GL Mechanical Tester with the 2000-lb or 5000-lb load cells. Test rate was 2"/min. for plastic bonds, and 0.1"/min. for metal and glass bonds at 73°F (23°C)., Substrate Failure/Break/Yield
1,050 psi Overlap shear strength ABS 23°C Overlap Shear Test Method: Overlap shear test for adhesion determined in accordance to ASTM D1002. Sampe dimenions were 1" x 4" x 1/8" (unless other thicknesses indicated) with an overlap area of 1" x 1/2". Plastics and glass substrates were cleansed with isopropyl alcohol (IPA) wipes, metal substrates were abraded with 150-grit sandpaper and cleansed with methyl ethyl ketone (MEK) wipes. All bonds were allowed to cure for a minimum of 48 hours at 73°F (23°C) before tested. Data were collected using a Sintech 5GL Mechanical Tester with the 2000-lb or 5000-lb load cells. Test rate was 2"/min. for plastic bonds, and 0.1"/min. for metal and glass bonds at 73°F (23°C)., Substrate Failure/Break/Yield
1,150 psi Overlap shear strength Lexan 23°C Overlap Shear Test Method: Overlap shear test for adhesion determined in accordance to ASTM D1002. Sampe dimenions were 1" x 4" x 1/8" (unless other thicknesses indicated) with an overlap area of 1" x 1/2". Plastics and glass substrates were cleansed with isopropyl alcohol (IPA) wipes, metal substrates were abraded with 150-grit sandpaper and cleansed with methyl ethyl ketone (MEK) wipes. All bonds were allowed to cure for a minimum of 48 hours at 73°F (23°C) before tested. Data were collected using a Sintech 5GL Mechanical Tester with the 2000-lb or 5000-lb load cells. Test rate was 2"/min. for plastic bonds, and 0.1"/min. for metal and glass bonds at 73°F (23°C)., Mixed (Mode of Adhesive Failure and Cohesive Failure)
2,050 psi Overlap shear strength Plexiglass (PMMA) 23°C
575 psi Overlap shear strength PVC 23°C Overlap Shear Test Method: Overlap shear test for adhesion determined in accordance to ASTM D1002. Sampe dimenions were 1" x 4" x 1/8" (unless other thicknesses indicated) with an overlap area of 1" x 1/2". Plastics and glass substrates were cleansed with isopropyl alcohol (IPA) wipes, metal substrates were abraded with 150-grit sandpaper and cleansed with methyl ethyl ketone (MEK) wipes. All bonds were allowed to cure for a minimum of 48 hours at 73°F (23°C) before tested. Data were collected using a Sintech 5GL Mechanical Tester with the 2000-lb or 5000-lb load cells. Test rate was 2"/min. for plastic bonds, and 0.1"/min. for metal and glass bonds at 73°F (23°C)., Substrate Failure/Break/Yield
475 psi Overlap shear strength HIPS 23°C Overlap Shear Test Method: Overlap shear test for adhesion determined in accordance to ASTM D1002. Sampe dimenions were 1" x 4" x 1/8" (unless other thicknesses indicated) with an overlap area of 1" x 1/2". Plastics and glass substrates were cleansed with isopropyl alcohol (IPA) wipes, metal substrates were abraded with 150-grit sandpaper and cleansed with methyl ethyl ketone (MEK) wipes. All bonds were allowed to cure for a minimum of 48 hours at 73°F (23°C) before tested. Data were collected using a Sintech 5GL Mechanical Tester with the 2000-lb or 5000-lb load cells. Test rate was 2"/min. for plastic bonds, and 0.1"/min. for metal and glass bonds at 73°F (23°C)., Substrate Failure/Break/Yield
2,525 psi Overlap shear strength PTFE 23°C Overlap Shear Test Method: Overlap shear test for adhesion determined in accordance to ASTM D1002. Sampe dimenions were 1" x 4" x 1/8" (unless other thicknesses indicated) with an overlap area of 1" x 1/2". Plastics and glass substrates were cleansed with isopropyl alcohol (IPA) wipes, metal substrates were abraded with 150-grit sandpaper and cleansed with methyl ethyl ketone (MEK) wipes. All bonds were allowed to cure for a minimum of 48 hours at 73°F (23°C) before tested. Data were collected using a Sintech 5GL Mechanical Tester with the 2000-lb or 5000-lb load cells. Test rate was 2"/min. for plastic bonds, and 0.1"/min. for metal and glass bonds at 73°F (23°C)., Substrate Failure/Break/Yield
750 psi Overlap shear strength Green FRP 23°C Overlap Shear Test Method: Overlap shear test for adhesion determined in accordance to ASTM D1002. Sampe dimenions were 1" x 4" x 1/8" (unless other thicknesses indicated) with an overlap area of 1" x 1/2". Plastics and glass substrates were cleansed with isopropyl alcohol (IPA) wipes, metal substrates were abraded with 150-grit sandpaper and cleansed with methyl ethyl ketone (MEK) wipes. All bonds were allowed to cure for a minimum of 48 hours at 73°F (23°C) before tested. Data were collected using a Sintech 5GL Mechanical Tester with the 2000-lb or 5000-lb load cells. Test rate was 2"/min. for plastic bonds, and 0.1"/min. for metal and glass bonds at 73°F (23°C)., Adhesive Failure
600 psi Overlap shear strength Polystyrene 23°C Overlap Shear Test Method: Overlap shear test for adhesion determined in accordance to ASTM D1002. Sampe dimenions were 1" x 4" x 1/8" (unless other thicknesses indicated) with an overlap area of 1" x 1/2". Plastics and glass substrates were cleansed with isopropyl alcohol (IPA) wipes, metal substrates were abraded with 150-grit sandpaper and cleansed with methyl ethyl ketone (MEK) wipes. All bonds were allowed to cure for a minimum of 48 hours at 73°F (23°C) before tested. Data were collected using a Sintech 5GL Mechanical Tester with the 2000-lb or 5000-lb load cells. Test rate was 2"/min. for plastic bonds, and 0.1"/min. for metal and glass bonds at 73°F (23°C)., Mixed (Mode of Adhesive Failure and Cohesive Failure)
1,450 psi Overlap shear strength Glass (3/16" thick) 23°C
1,875 psi Overlap shear strength Gel Coat (3/16" thick) 23°C Overlap Shear Test Method: Overlap shear test for adhesion determined in accordance to ASTM D1002. Sampe dimenions were 1" x 4" x 1/8" (unless other thicknesses indicated) with an overlap area of 1" x 1/2". Plastics and glass substrates were cleansed with isopropyl alcohol (IPA) wipes, metal substrates were abraded with 150-grit sandpaper and cleansed with methyl ethyl ketone (MEK) wipes. All bonds were allowed to cure for a minimum of 48 hours at 73°F (23°C) before tested. Data were collected using a Sintech 5GL Mechanical Tester with the 2000-lb or 5000-lb load cells. Test rate was 2"/min. for plastic bonds, and 0.1"/min. for metal and glass bonds at 73°F (23°C)., Substrate Failure/Break/Yield
1,950 psi Overlap shear strength Copper (1/16" thick) 23°C
2,050 psi Overlap shear strength Aluminum (1/16" thick) 23°C Overlap Shear Test Method: Overlap shear test for adhesion determined in accordance to ASTM D1002. Sampe dimenions were 1" x 4" x 1/8" (unless other thicknesses indicated) with an overlap area of 1" x 1/2". Plastics and glass substrates were cleansed with isopropyl alcohol (IPA) wipes, metal substrates were abraded with 150-grit sandpaper and cleansed with methyl ethyl ketone (MEK) wipes. All bonds were allowed to cure for a minimum of 48 hours at 73°F (23°C) before tested. Data were collected using a Sintech 5GL Mechanical Tester with the 2000-lb or 5000-lb load cells. Test rate was 2"/min. for plastic bonds, and 0.1"/min. for metal and glass bonds at 73°F (23°C)., Substrate Failure/Break/Yield
1,200 psi Overlap shear strength Cold-Rolled Steel (1/32" thick) 23°C
150 psi Overlap shear strength 304 Stainless Steel (1/32" thick) 23°C Overlap Shear Test Method: Overlap shear test for adhesion determined in accordance to ASTM D1002. Sampe dimenions were 1" x 4" x 1/8" (unless other thicknesses indicated) with an overlap area of 1" x 1/2". Plastics and glass substrates were cleansed with isopropyl alcohol (IPA) wipes, metal substrates were abraded with 150-grit sandpaper and cleansed with methyl ethyl ketone (MEK) wipes. All bonds were allowed to cure for a minimum of 48 hours at 73°F (23°C) before tested. Data were collected using a Sintech 5GL Mechanical Tester with the 2000-lb or 5000-lb load cells. Test rate was 2"/min. for plastic bonds, and 0.1"/min. for metal and glass bonds at 73°F (23°C)., Substrate Failure/Break/Yield
850 psi Overlap shear strength Acetal 23°C
125 psi Overlap shear strength CRS/HDPE (non-abraded CRS) 23°C Overlap Shear Test Method: Overlap shear test for adhesion determined in accordance to ASTM D1002. Sampe dimenions were 1" x 4" x 1/8" (unless other thicknesses indicated) with an overlap area of 1" x 1/2". Plastics and glass substrates were cleansed with isopropyl alcohol (IPA) wipes, metal substrates were abraded with 150-grit sandpaper and cleansed with methyl ethyl ketone (MEK) wipes. All bonds were allowed to cure for a minimum of 48 hours at 73°F (23°C) before tested. Data were collected using a Sintech 5GL Mechanical Tester with the 2000-lb or 5000-lb load cells. Test rate was 2"/min. for plastic bonds, and 0.1"/min. for metal and glass bonds at 73°F (23°C)., Mixed (Mode of Adhesive Failure and Cohesive Failure)
1,025 psi Overlap shear strength Aluminum/HDPE (non-abraded aluminum) 23°C Overlap Shear Test Method: Overlap shear test for adhesion determined in accordance to ASTM D1002. Sampe dimenions were 1" x 4" x 1/8" (unless other thicknesses indicated) with an overlap area of 1" x 1/2". Plastics and glass substrates were cleansed with isopropyl alcohol (IPA) wipes, metal substrates were abraded with 150-grit sandpaper and cleansed with methyl ethyl ketone (MEK) wipes. All bonds were allowed to cure for a minimum of 48 hours at 73°F (23°C) before tested. Data were collected using a Sintech 5GL Mechanical Tester with the 2000-lb or 5000-lb load cells. Test rate was 2"/min. for plastic bonds, and 0.1"/min. for metal and glass bonds at 73°F (23°C)., Adhesive Failure
1,375 psi Overlap shear strength ED-5000 E-Coated CRS/HDPE 23°C Overlap Shear Test Method: Overlap shear test for adhesion determined in accordance to ASTM D1002. Sampe dimenions were 1" x 4" x 1/8" (unless other thicknesses indicated) with an overlap area of 1" x 1/2". Plastics and glass substrates were cleansed with isopropyl alcohol (IPA) wipes, metal substrates were abraded with 150-grit sandpaper and cleansed with methyl ethyl ketone (MEK) wipes. All bonds were allowed to cure for a minimum of 48 hours at 73°F (23°C) before tested. Data were collected using a Sintech 5GL Mechanical Tester with the 2000-lb or 5000-lb load cells. Test rate was 2"/min. for plastic bonds, and 0.1"/min. for metal and glass bonds at 73°F (23°C)., Adhesive Failure
1,500 psi Overlap shear strength EC 3924 Primed CRS (non-abraded CRS) 23°C Overlap Shear Test Method: Overlap shear test for adhesion determined in accordance to ASTM D1002. Sampe dimenions were 1" x 4" x 1/8" (unless other thicknesses indicated) with an overlap area of 1" x 1/2". Plastics and glass substrates were cleansed with isopropyl alcohol (IPA) wipes, metal substrates were abraded with 150-grit sandpaper and cleansed with methyl ethyl ketone (MEK) wipes. All bonds were allowed to cure for a minimum of 48 hours at 73°F (23°C) before tested. Data were collected using a Sintech 5GL Mechanical Tester with the 2000-lb or 5000-lb load cells. Test rate was 2"/min. for plastic bonds, and 0.1"/min. for metal and glass bonds at 73°F (23°C)., Adhesive Failure
950 psi Overlap shear strength EC 3924 Primed Al/HDPE (non-abraded Al) 23°C Overlap Shear Test Method: Overlap shear test for adhesion determined in accordance to ASTM D1002. Sampe dimenions were 1" x 4" x 1/8" (unless other thicknesses indicated) with an overlap area of 1" x 1/2". Plastics and glass substrates were cleansed with isopropyl alcohol (IPA) wipes, metal substrates were abraded with 150-grit sandpaper and cleansed with methyl ethyl ketone (MEK) wipes. All bonds were allowed to cure for a minimum of 48 hours at 73°F (23°C) before tested. Data were collected using a Sintech 5GL Mechanical Tester with the 2000-lb or 5000-lb load cells. Test rate was 2"/min. for plastic bonds, and 0.1"/min. for metal and glass bonds at 73°F (23°C)., Adhesive Failure
600 psi Overlap shear strength DCT 5002X Top Coat CRS/HDPE (non-abraded CRS) 23°C Overlap Shear Test Method: Overlap shear test for adhesion determined in accordance to ASTM D1002. Sampe dimenions were 1" x 4" x 1/8" (unless other thicknesses indicated) with an overlap area of 1" x 1/2". Plastics and glass substrates were cleansed with isopropyl alcohol (IPA) wipes, metal substrates were abraded with 150-grit sandpaper and cleansed with methyl ethyl ketone (MEK) wipes. All bonds were allowed to cure for a minimum of 48 hours at 73°F (23°C) before tested. Data were collected using a Sintech 5GL Mechanical Tester with the 2000-lb or 5000-lb load cells. Test rate was 2"/min. for plastic bonds, and 0.1"/min. for metal and glass bonds at 73°F (23°C)., Adhesive Failure to CRS
Peel Strength Test Methods
Peel Strength Type Substrate Test Temperature Test Method
30 piw T-Peel Strength HDPE 23°C Peel tests on 0.02" thick HDPE, 0.017" bondline thickness, 8" x 1" in T-peel mode at a rate of 2.0"/min.
Coefficient of Thermal Expansion (CTE) Test Methods
Coefficient of Thermal Expansion (CTE) CTE Temperature (°C) CTE Test Method
132 (ppm/°C) -40 to 120°C Tg and CTE determined by TMA -40°F to 249°F (-40°C to 120°C) at 10°F (5°C)/min. (after 2 heat cycles).
207 (ppm/°C) -40 to 120°C Tg and CTE determined by TMA -40°F to 249°F (-40°C to 120°C) at 10°F (5°C)/min. (after 2 heat cycles).
Glass Transition Temp (Tg) Test Methods
Glass Transition Temp (Tg) Glass Transition Temperature (Tg) Test Method
34°C Tg and CTE determined by TMA -40°F to 249°F (-40°C to 120°C) at 10°F (5°C)/min. (after 2 heat cycles).