Excellent |
|
|
|
|
|
|
|
|
|
4,200 psi |
Overlap Shear Strength |
10,080 min |
24°C |
50 % |
Aluminum – etched |
|
|
23°C |
Overlap Shear (ASTM D-1002-64, 3M Test Method C-236) strength was measured on 1" wide x 1/2" overlap specimen. These bonds were made individually using 1" x 4" pieces of substrates. The thickness of the adhesive bond line was approximately 0.005". All strengths were measured at 73°F (23°C) except when noted, and samples were allowed to cure at 75°F (24°C) and approximately 50% RH for 1 week before tested. The separation rate of the testing jaws was 0.1 inch per minute for metals and 2 inches per minute for plastics, Adhesive failure |
4,100 psi |
Overlap Shear Strength |
10,080 min |
24°C |
50 % |
Aluminum – abraded, 150 grit sandpaper |
|
|
23°C |
Overlap Shear (ASTM D-1002-64, 3M Test Method C-236) strength was measured on 1" wide x 1/2" overlap specimen. These bonds were made individually using 1" x 4" pieces of substrates. The thickness of the adhesive bond line was approximately 0.005". All strengths were measured at 73°F (23°C) except when noted, and samples were allowed to cure at 75°F (24°C) and approximately 50% RH for 1 week before tested. The separation rate of the testing jaws was 0.1 inch per minute for metals and 2 inches per minute for plastics, Adhesive failure |
4,350 psi |
Overlap Shear Strength |
10,080 min |
24°C |
50 % |
Aluminum – bare |
|
|
23°C |
Overlap Shear (ASTM D-1002-64, 3M Test Method C-236) strength was measured on 1" wide x 1/2" overlap specimen. These bonds were made individually using 1" x 4" pieces of substrates. The thickness of the adhesive bond line was approximately 0.005". All strengths were measured at 73°F (23°C) except when noted, and samples were allowed to cure at 75°F (24°C) and approximately 50% RH for 1 week before tested. The separation rate of the testing jaws was 0.1 inch per minute for metals and 2 inches per minute for plastics, Adhesive failure |
3,125 psi |
Overlap Shear Strength |
10,080 min |
24°C |
50 % |
Cold-Rolled Steel (CRS) – solvent cleaned |
|
|
23°C |
Overlap Shear (ASTM D-1002-64, 3M Test Method C-236) strength was measured on 1" wide x 1/2" overlap specimen. These bonds were made individually using 1" x 4" pieces of substrates. The thickness of the adhesive bond line was approximately 0.005". All strengths were measured at 73°F (23°C) except when noted, and samples were allowed to cure at 75°F (24°C) and approximately 50% RH for 1 week before tested. The separation rate of the testing jaws was 0.1 inch per minute for metals and 2 inches per minute for plastics, Adhesive failure |
2,600 psi |
Overlap Shear Strength |
10,080 min |
24°C |
50 % |
Cold-Rolled Steel – slightly oily |
|
|
23°C |
Overlap Shear (ASTM D-1002-64, 3M Test Method C-236) strength was measured on 1" wide x 1/2" overlap specimen. These bonds were made individually using 1" x 4" pieces of substrates. The thickness of the adhesive bond line was approximately 0.005". All strengths were measured at 73°F (23°C) except when noted, and samples were allowed to cure at 75°F (24°C) and approximately 50% RH for 1 week before tested. The separation rate of the testing jaws was 0.1 inch per minute for metals and 2 inches per minute for plastics, Cohesive failure |
4,050 psi |
Overlap Shear Strength |
10,080 min |
24°C |
50 % |
Stainless Steel |
|
|
23°C |
Overlap Shear (ASTM D-1002-64, 3M Test Method C-236) strength was measured on 1" wide x 1/2" overlap specimen. These bonds were made individually using 1" x 4" pieces of substrates. The thickness of the adhesive bond line was approximately 0.005". All strengths were measured at 73°F (23°C) except when noted, and samples were allowed to cure at 75°F (24°C) and approximately 50% RH for 1 week before tested. The separation rate of the testing jaws was 0.1 inch per minute for metals and 2 inches per minute for plastics, Adhesive failure |
2,775 psi |
Overlap Shear Strength |
10,080 min |
24°C |
50 % |
Green Fiberglass Reinforced Plastic |
|
|
23°C |
Overlap Shear (ASTM D-1002-64, 3M Test Method C-236) strength was measured on 1" wide x 1/2" overlap specimen. These bonds were made individually using 1" x 4" pieces of substrates. The thickness of the adhesive bond line was approximately 0.005". All strengths were measured at 73°F (23°C) except when noted, and samples were allowed to cure at 75°F (24°C) and approximately 50% RH for 1 week before tested. The separation rate of the testing jaws was 0.1 inch per minute for metals and 2 inches per minute for plastics, Adhesive failure |
1,025 psi |
Overlap Shear Strength |
10,080 min |
24°C |
50 % |
Acrylic |
|
|
23°C |
Overlap Shear (ASTM D-1002-64, 3M Test Method C-236) strength was measured on 1" wide x 1/2" overlap specimen. These bonds were made individually using 1" x 4" pieces of substrates. The thickness of the adhesive bond line was approximately 0.005". All strengths were measured at 73°F (23°C) except when noted, and samples were allowed to cure at 75°F (24°C) and approximately 50% RH for 1 week before tested. The separation rate of the testing jaws was 0.1 inch per minute for metals and 2 inches per minute for plastics, Substrate failure |
1,300 psi |
Overlap Shear Strength |
10,080 min |
24°C |
50 % |
Polyvinylchloride (PVC) |
|
|
23°C |
Overlap Shear (ASTM D-1002-64, 3M Test Method C-236) strength was measured on 1" wide x 1/2" overlap specimen. These bonds were made individually using 1" x 4" pieces of substrates. The thickness of the adhesive bond line was approximately 0.005". All strengths were measured at 73°F (23°C) except when noted, and samples were allowed to cure at 75°F (24°C) and approximately 50% RH for 1 week before tested. The separation rate of the testing jaws was 0.1 inch per minute for metals and 2 inches per minute for plastics, Substrate failure |
950 psi |
Overlap Shear Strength |
10,080 min |
24°C |
50 % |
Polycarbonate (PC) |
|
|
23°C |
Overlap Shear (ASTM D-1002-64, 3M Test Method C-236) strength was measured on 1" wide x 1/2" overlap specimen. These bonds were made individually using 1" x 4" pieces of substrates. The thickness of the adhesive bond line was approximately 0.005". All strengths were measured at 73°F (23°C) except when noted, and samples were allowed to cure at 75°F (24°C) and approximately 50% RH for 1 week before tested. The separation rate of the testing jaws was 0.1 inch per minute for metals and 2 inches per minute for plastics, Substrate failure |
1,000 psi |
Overlap Shear Strength |
10,080 min |
24°C |
50 % |
Acrylonitrile Butadiene Styrene (ABS) |
|
|
23°C |
Overlap Shear (ASTM D-1002-64, 3M Test Method C-236) strength was measured on 1" wide x 1/2" overlap specimen. These bonds were made individually using 1" x 4" pieces of substrates. The thickness of the adhesive bond line was approximately 0.005". All strengths were measured at 73°F (23°C) except when noted, and samples were allowed to cure at 75°F (24°C) and approximately 50% RH for 1 week before tested. The separation rate of the testing jaws was 0.1 inch per minute for metals and 2 inches per minute for plastics, Substrate failure |
4,725 psi |
Overlap Shear Strength |
10,080 min |
|
50 % |
Etched Aluminum |
Control (no immersion) |
604,800 sec |
|
Overlap Shear (ASTM D-1002-64, 3M Test Method C-236) strength was measured on 1" wide x 1/2" overlap specimen. These bonds were made individually using 1" x 4" coupons. The thickness of the adhesive bond line was approximately 0.005". All strengths were measured at 73°F (23°C) except when noted, and samples were allowed to cure at 75°F (24°C) and approximately 50% RH for 1 week before immersed. The separation rate of the testing jaws was 0.1 inch per minute |
3,150 psi |
Overlap Shear Strength |
|
66°C |
50 % |
Etched Aluminum |
|
604,800 sec |
|
Overlap Shear (ASTM D-1002-64, 3M Test Method C-236) strength was measured on 1" wide x 1/2" overlap specimen. These bonds were made individually using 1" x 4" coupons. The thickness of the adhesive bond line was approximately 0.005". All strengths were measured at 73°F (23°C) except when noted, and samples were allowed to cure at 75°F (24°C) and approximately 50% RH for 1 week before immersed. The separation rate of the testing jaws was 0.1 inch per minute |
2,250 psi |
Overlap Shear Strength |
|
66°C |
50 % |
Etched Aluminum |
Tap water |
604,800 sec |
|
Overlap Shear (ASTM D-1002-64, 3M Test Method C-236) strength was measured on 1" wide x 1/2" overlap specimen. These bonds were made individually using 1" x 4" coupons. The thickness of the adhesive bond line was approximately 0.005". All strengths were measured at 73°F (23°C) except when noted, and samples were allowed to cure at 75°F (24°C) and approximately 50% RH for 1 week before immersed. The separation rate of the testing jaws was 0.1 inch per minute |
4,125 psi |
Overlap Shear Strength |
|
|
50 % |
Etched Aluminum |
20% Bleach solution |
604,800 sec |
|
Overlap Shear (ASTM D-1002-64, 3M Test Method C-236) strength was measured on 1" wide x 1/2" overlap specimen. These bonds were made individually using 1" x 4" coupons. The thickness of the adhesive bond line was approximately 0.005". All strengths were measured at 73°F (23°C) except when noted, and samples were allowed to cure at 75°F (24°C) and approximately 50% RH for 1 week before immersed. The separation rate of the testing jaws was 0.1 inch per minute |
4,100 psi |
Overlap Shear Strength |
|
|
50 % |
Etched Aluminum |
IPA (isopropyl alcohol) |
604,800 sec |
|
Overlap Shear (ASTM D-1002-64, 3M Test Method C-236) strength was measured on 1" wide x 1/2" overlap specimen. These bonds were made individually using 1" x 4" coupons. The thickness of the adhesive bond line was approximately 0.005". All strengths were measured at 73°F (23°C) except when noted, and samples were allowed to cure at 75°F (24°C) and approximately 50% RH for 1 week before immersed. The separation rate of the testing jaws was 0.1 inch per minute |
2,600 psi |
Overlap Shear Strength |
|
|
50 % |
Etched Aluminum |
Unleaded gasoline |
604,800 sec |
|
Overlap Shear (ASTM D-1002-64, 3M Test Method C-236) strength was measured on 1" wide x 1/2" overlap specimen. These bonds were made individually using 1" x 4" coupons. The thickness of the adhesive bond line was approximately 0.005". All strengths were measured at 73°F (23°C) except when noted, and samples were allowed to cure at 75°F (24°C) and approximately 50% RH for 1 week before immersed. The separation rate of the testing jaws was 0.1 inch per minute |
5,000 psi |
Overlap Shear Strength |
|
|
50 % |
Etched Aluminum |
Diesel fuel |
604,800 sec |
|
Overlap Shear (ASTM D-1002-64, 3M Test Method C-236) strength was measured on 1" wide x 1/2" overlap specimen. These bonds were made individually using 1" x 4" coupons. The thickness of the adhesive bond line was approximately 0.005". All strengths were measured at 73°F (23°C) except when noted, and samples were allowed to cure at 75°F (24°C) and approximately 50% RH for 1 week before immersed. The separation rate of the testing jaws was 0.1 inch per minute |
5,150 psi |
Overlap Shear Strength |
|
|
50 % |
Etched Aluminum |
50% Antifreeze |
604,800 sec |
|
Overlap Shear (ASTM D-1002-64, 3M Test Method C-236) strength was measured on 1" wide x 1/2" overlap specimen. These bonds were made individually using 1" x 4" coupons. The thickness of the adhesive bond line was approximately 0.005". All strengths were measured at 73°F (23°C) except when noted, and samples were allowed to cure at 75°F (24°C) and approximately 50% RH for 1 week before immersed. The separation rate of the testing jaws was 0.1 inch per minute |
875 psi |
Overlap Shear Strength |
|
|
50 % |
Etched Aluminum |
Toluene |
604,800 sec |
|
Overlap Shear (ASTM D-1002-64, 3M Test Method C-236) strength was measured on 1" wide x 1/2" overlap specimen. These bonds were made individually using 1" x 4" coupons. The thickness of the adhesive bond line was approximately 0.005". All strengths were measured at 73°F (23°C) except when noted, and samples were allowed to cure at 75°F (24°C) and approximately 50% RH for 1 week before immersed. The separation rate of the testing jaws was 0.1 inch per minute |
2,000 psi |
Overlap Shear Strength |
10,080 min |
23°C |
50 % |
Etched Aluminum |
MEK (methyl ethyl ketone) |
|
-55°C |
Overlap Shear (ASTM D1002-64, 3M Test Method C-236) strength was measured on 1 in. wide x 1/2 in. overlap specimens. These bonds were made individually using 1" x 4" coupons. The thickness of the adhesive bond line was approximately 0.005". Bonds were allowed to cured for 7 days @ 73°F (23°C) and approximately 50% RH before tested. The separation rate of the testing jaws was 0.1 inch per minute. |
4,275 psi |
Overlap Shear Strength |
10,080 min |
23°C |
50 % |
Etched Aluminum |
Acetone |
|
24°C |
Overlap Shear (ASTM D1002-64, 3M Test Method C-236) strength was measured on 1 in. wide x 1/2 in. overlap specimens. These bonds were made individually using 1" x 4" coupons. The thickness of the adhesive bond line was approximately 0.005". Bonds were allowed to cured for 7 days @ 73°F (23°C) and approximately 50% RH before tested. The separation rate of the testing jaws was 0.1 inch per minute. |
2,600 psi |
Overlap Shear Strength |
10,080 min |
23°C |
50 % |
Etched Aluminum |
|
|
49°C |
Overlap Shear (ASTM D1002-64, 3M Test Method C-236) strength was measured on 1 in. wide x 1/2 in. overlap specimens. These bonds were made individually using 1" x 4" coupons. The thickness of the adhesive bond line was approximately 0.005". Bonds were allowed to cured for 7 days @ 73°F (23°C) and approximately 50% RH before tested. The separation rate of the testing jaws was 0.1 inch per minute. |
825 psi |
Overlap Shear Strength |
10,080 min |
23°C |
50 % |
Etched Aluminum |
|
|
82°C |
Overlap Shear (ASTM D1002-64, 3M Test Method C-236) strength was measured on 1 in. wide x 1/2 in. overlap specimens. These bonds were made individually using 1" x 4" coupons. The thickness of the adhesive bond line was approximately 0.005". Bonds were allowed to cured for 7 days @ 73°F (23°C) and approximately 50% RH before tested. The separation rate of the testing jaws was 0.1 inch per minute. |