| Application Type | Bond |
|---|---|
| 1 Part or 2 Part | 2 Part |
| Material Form | Liquid |
| Substrate | Abraded Aluminum, Ceramic, Steel, Glass, Metal, ABS, Polycarbonate, PVC, Rubber, Stainless Steel, Wood, Acrylic, Green FRP, Bare Aluminum, CRS, Plastic, Etched Aluminum, Oily CRS |
| Manufacturer | 3M |
| Chemistry | Acrylic |
| Cure Method | Base/Accelerator |
| Cure Temperature (°C) | 23 |
| Cure Time (min) | 480 to 1,440 |
| Viscosity (cPs) | 18,000 to 20,000 |
| Chemical Resistance | 160F (71C)/100% RH, 160F (71C)/Soak, 20% Bleach, 50% Antifreeze, Acetone, Control, Diesel Fuel, Gasoline, IPA (isopropyl alcohol), MEK |
| High Temperature Resistance (°C) | 82 |
| Low Temperature Resistance (°C) | -29 |
| Density (g/cm³) | 8.7 to 9.1 (lbs/gal) |
3M™ Scotch-Weld™ Low-Odor Acrylic Adhesives can bond oily metal, plastic and other substrates with very little surface preparation. However, for the most consistent results and environmental resistance, all substrates should be clean, dry and free of paint, oxide films, dust, mold release agents and all other surface contaminants. The amount of surface preparation directly depends on the bond strength and environmental resistance desired by the user.
The following cleaning methods are suggested for common surfaces.: Wipe free of dust with oil-free solvent such as acetone or isopropyl alcohol.
Sandblast or abrade using clean fine grit abrasives (180 grit or finer).
Wipe again with solvent to remove loose particles.
If a primer is used, it should be applied within 4 hours after surface preparation (or see instructions pertinent to a specific primer).
Note: Aluminum may also be acid etched. Follow the manufacturer’s precautions and directions for this procedure.
Wipe with isopropyl alcohol.
Abrade using fine grit abrasives (180 grit or finer).
Remove residue by wiping again with isopropyl alcohol.
Solvent wipe surface using acetone.
Apply a thin coating (0.0001" or less) of 3M™ Scotch-Weld™ EC-3901 Primer to the glass surfaces to be bonded and allow the primer to dry a minimum of 30 minutes at 75°F (24°C) before bonding for maximum adhesion.
Remove residue by wiping again with isopropyl alcohol.
Note: When using solvents, extinguish all ignition sources and follow the manufacturer’s precautions and directions for use.
Directions for use: Apply adhesive to clean, dry substrates, which are free of paint, oxide films, oils, dust, mold release agents and all other surface contaminants. See the Surface Preparation section for specific substrate preparation method.
Excess adhesive can be removed with solvent such as 3M™ Scotch-Grip™ Solvent No. 3 or equivalent. Edge tack on a finished part or bond line can be removed with isopropyl alcohol*.
*Note: When using solvents, extinguish all ignition sources and follow the manufacturer’s precautions and directions for use.
| dolor nibh aliquam erat. | tincidunt. | lorem. |
|---|---|---|
| amet nonummy. | magna ipsum tincidunt. | elit. |
| nonummy elit sed laoreet. | laoreet dolor laoreet. | lorem. |
| dolor ut erat. | magna. | dolor aliquam. |
| laoreet nibh nibh magna. | sed nonummy. | aliquam. |
| ipsum dolore magna. | magna elit dolor. | ipsum. |
| consectetuer ipsum nibh nonummy. | erat laoreet. | aliquam. |
| euismod. | ut. | elit erat. |
|---|---|---|
| magna aliquam sed amet. | diam ipsum diam. | euismod ipsum. |
| ut nonummy lorem. | consectetuer dolor nibh. | diam amet. |
| aliquam diam laoreet nibh. | dolore sed dolore. | sit. |
|---|---|---|
| amet nibh. | dolore tincidunt. | magna nonummy. |
| magna ut dolore. | adipiscing magna euismod. | sit. |
| laoreet. | ipsum ipsum. | ipsum sed. |
| adipiscing magna sed aliquam. | laoreet diam. | adipiscing laoreet. |
| ut erat sed. | aliquam euismod dolore. | amet. |
| dolore erat. | dolore. | sit lorem. |
| lorem tincidunt lorem. | lorem tincidunt. | adipiscing ut. |
| amet dolor. | dolore consectetuer. | euismod tincidunt. |
| laoreet diam elit. | consectetuer aliquam. | euismod aliquam. |
|---|---|---|
| sit. | adipiscing. | nibh. |
| ipsum. | lorem nibh adipiscing. | consectetuer. |
| laoreet lorem. | ipsum laoreet sit. | sit. |
| lorem nibh dolore. | diam ut sit. | ipsum sit. |
| nibh erat erat. | aliquam. | ut sit. |
| adipiscing. | sed sed diam. | nonummy. |
| tincidunt erat. | nibh elit erat. | aliquam euismod. |
| nonummy dolore tincidunt ipsum. | aliquam. | nonummy. |
| aliquam nibh elit. | adipiscing erat diam. | tincidunt diam. |
|---|---|---|
| consectetuer elit amet. | consectetuer. | adipiscing elit. |
| amet dolor. | diam. | amet dolore. |
dolor sit consectetuer elit ipsum diam. magna ipsum lorem euismod consectetuer magna. ipsum nibh nibh diam elit euismod. consectetuer aliquam sit adipiscing amet dolore. nonummy adipiscing nibh erat laoreet sit.
sed ipsum aliquam ut dolore ipsum erat diam sit magna. euismod nibh laoreet magna ut magna nibh laoreet dolor sit. dolore magna dolore erat diam dolore laoreet magna aliquam consectetuer. dolore erat diam sit euismod diam tincidunt ut nonummy nonummy. consectetuer diam lorem diam nibh consectetuer laoreet diam magna dolor.
dolor nibh magna lorem tincidunt ipsum euismod consectetuer. amet sit magna amet nibh magna elit dolore. adipiscing sed sit ipsum consectetuer erat laoreet dolor. sed sed magna adipiscing ipsum sit laoreet sed. nibh amet sit aliquam sit diam magna amet.
nonummy ipsum aliquam lorem dolor laoreet ut euismod consectetuer sit consectetuer sit. ipsum sed diam tincidunt elit ut diam tincidunt magna nonummy erat magna. ipsum elit dolore dolore amet sed sit dolore adipiscing amet amet adipiscing. tincidunt sit ipsum dolor sed dolore euismod lorem magna lorem nibh nonummy.
erat lorem ipsum dolor lorem dolor lorem aliquam ut aliquam. magna elit dolore lorem sed dolore dolore sit dolor erat. sit tincidunt adipiscing amet lorem magna erat lorem ipsum laoreet. adipiscing lorem tincidunt dolore sit dolore consectetuer dolor amet amet.
ut adipiscing euismod nonummy sed adipiscing tincidunt. dolore ipsum dolor dolor lorem magna erat. euismod magna tincidunt lorem magna nibh nibh.
adipiscing aliquam elit dolor ut nibh dolor erat nonummy magna ipsum erat. elit dolor sed dolore dolor diam lorem dolor ipsum euismod adipiscing elit. nibh tincidunt laoreet ut dolor magna euismod erat sed ut amet diam. erat nonummy ipsum nonummy erat sit diam lorem magna euismod diam nonummy. euismod lorem sed ipsum tincidunt dolore magna tincidunt euismod lorem nonummy lorem.
| Fixture or Handling Strength Time | Fixture-Handling Strength Test Method |
|---|---|
| 10 min | Time to Handling Strength (50 psi) |
| Work / Pot Time | Temperature |
|---|---|
| 10 min | 23°C |
| Shear Strength | Type | Cure Time | Cure Temperature | Substrate | Test Time | Test Temperature | Test Method |
|---|---|---|---|---|---|---|---|
| Excellent | |||||||
| 4,200 psi | Overlap Shear Strength | 360 min | 24°C | Etched Aluminum | 23°C | Cohesive Failure, Overlap Shear Test Method: overlap shear test for adhesion determined in accordance to ASTM D1002-72, sample dimensions were 1" x 4" x 1/8", with a 1/2 square inch area of overlap, bonded to themselves unless otherwise noted, allowed to cure for at least 6 hours at 75°F (24°C) before testing. Data were collected using a Sintech 5GL Mechanical Tester with a 2000# or 5000# load cell. Test rate was 0.1"/minute. Strength determined at 75°F (24°C) unless otherwise noted. | |
| 3,900 psi | Overlap Shear Strength | 360 min | 24°C | Abraded Aluminum | 23°C | Cohesive Failure, Overlap Shear Test Method: overlap shear test for adhesion determined in accordance to ASTM D1002-72, sample dimensions were 1" x 4" x 1/8", with a 1/2 square inch area of overlap, bonded to themselves unless otherwise noted, allowed to cure for at least 6 hours at 75°F (24°C) before testing. Data were collected using a Sintech 5GL Mechanical Tester with a 2000# or 5000# load cell. Test rate was 0.1"/minute. Strength determined at 75°F (24°C) unless otherwise noted. | |
| 3,800 psi | Overlap Shear Strength | 360 min | 24°C | Bare Aluminum | 23°C | Cohesive Failure, Overlap Shear Test Method: overlap shear test for adhesion determined in accordance to ASTM D1002-72, sample dimensions were 1" x 4" x 1/8", with a 1/2 square inch area of overlap, bonded to themselves unless otherwise noted, allowed to cure for at least 6 hours at 75°F (24°C) before testing. Data were collected using a Sintech 5GL Mechanical Tester with a 2000# or 5000# load cell. Test rate was 0.1"/minute. Strength determined at 75°F (24°C) unless otherwise noted. | |
| 3,100 psi | Overlap Shear Strength | 360 min | 24°C | CRS | 23°C | Cohesive Failure, Overlap Shear Test Method: overlap shear test for adhesion determined in accordance to ASTM D1002-72, sample dimensions were 1" x 4" x 1/8", with a 1/2 square inch area of overlap, bonded to themselves unless otherwise noted, allowed to cure for at least 6 hours at 75°F (24°C) before testing. Data were collected using a Sintech 5GL Mechanical Tester with a 2000# or 5000# load cell. Test rate was 0.1"/minute. Strength determined at 75°F (24°C) unless otherwise noted. | |
| 3,450 psi | Overlap Shear Strength | 360 min | 24°C | Oily CRS | 23°C | Cohesive Failure, Overlap Shear Test Method: overlap shear test for adhesion determined in accordance to ASTM D1002-72, sample dimensions were 1" x 4" x 1/8", with a 1/2 square inch area of overlap, bonded to themselves unless otherwise noted, allowed to cure for at least 6 hours at 75°F (24°C) before testing. Data were collected using a Sintech 5GL Mechanical Tester with a 2000# or 5000# load cell. Test rate was 0.1"/minute. Strength determined at 75°F (24°C) unless otherwise noted. | |
| 3,400 psi | Overlap Shear Strength | 360 min | 24°C | Stainless Steel | 23°C | Cohesive Failure, Overlap Shear Test Method: overlap shear test for adhesion determined in accordance to ASTM D1002-72, sample dimensions were 1" x 4" x 1/8", with a 1/2 square inch area of overlap, bonded to themselves unless otherwise noted, allowed to cure for at least 6 hours at 75°F (24°C) before testing. Data were collected using a Sintech 5GL Mechanical Tester with a 2000# or 5000# load cell. Test rate was 0.1"/minute. Strength determined at 75°F (24°C) unless otherwise noted. | |
| 3,800 psi | Overlap Shear Strength | 360 min | 24°C | Green FRP | 23°C | Cohesive Failure, Overlap Shear Test Method: overlap shear test for adhesion determined in accordance to ASTM D1002-72, sample dimensions were 1" x 4" x 1/8", with a 1/2 square inch area of overlap, bonded to themselves unless otherwise noted, allowed to cure for at least 6 hours at 75°F (24°C) before testing. Data were collected using a Sintech 5GL Mechanical Tester with a 2000# or 5000# load cell. Test rate was 0.1"/minute. Strength determined at 75°F (24°C) unless otherwise noted. | |
| 1,100 psi | Overlap Shear Strength | 360 min | 24°C | Acrylic | 23°C | Substrate Failure/Break, Overlap Shear Test Method: overlap shear test for adhesion determined in accordance to ASTM D1002-72, sample dimensions were 1" x 4" x 1/8", with a 1/2 square inch area of overlap, bonded to themselves unless otherwise noted, allowed to cure for at least 6 hours at 75°F (24°C) before testing. Data were collected using a Sintech 5GL Mechanical Tester with a 2000# or 5000# load cell. Test rate was 0.1"/minute. Strength determined at 75°F (24°C) unless otherwise noted. | |
| 1,000 psi | Overlap Shear Strength | 360 min | 24°C | PVC | 23°C | Substrate Failure/Break, Overlap Shear Test Method: overlap shear test for adhesion determined in accordance to ASTM D1002-72, sample dimensions were 1" x 4" x 1/8", with a 1/2 square inch area of overlap, bonded to themselves unless otherwise noted, allowed to cure for at least 6 hours at 75°F (24°C) before testing. Data were collected using a Sintech 5GL Mechanical Tester with a 2000# or 5000# load cell. Test rate was 0.1"/minute. Strength determined at 75°F (24°C) unless otherwise noted. | |
| 850 psi | Overlap Shear Strength | 360 min | 24°C | Polycarbonate | 23°C | Mixed (Mode of AF and CF), Overlap Shear Test Method: overlap shear test for adhesion determined in accordance to ASTM D1002-72, sample dimensions were 1" x 4" x 1/8", with a 1/2 square inch area of overlap, bonded to themselves unless otherwise noted, allowed to cure for at least 6 hours at 75°F (24°C) before testing. Data were collected using a Sintech 5GL Mechanical Tester with a 2000# or 5000# load cell. Test rate was 0.1"/minute. Strength determined at 75°F (24°C) unless otherwise noted. | |
| 600 psi | Overlap Shear Strength | 360 min | 24°C | ABS | 23°C | Mixed (Mode of AF and CF), Overlap Shear Test Method: overlap shear test for adhesion determined in accordance to ASTM D1002-72, sample dimensions were 1" x 4" x 1/8", with a 1/2 square inch area of overlap, bonded to themselves unless otherwise noted, allowed to cure for at least 6 hours at 75°F (24°C) before testing. Data were collected using a Sintech 5GL Mechanical Tester with a 2000# or 5000# load cell. Test rate was 0.1"/minute. Strength determined at 75°F (24°C) unless otherwise noted. | |
| 1,750 psi | Overlap Shear Strength | -29°C | Adhesive Failure/Mixed (Mode of AF and CF) | ||||
| 3,650 psi | Overlap Shear Strength | 24°C | Cohesive Failure | ||||
| 2,000 psi | Overlap Shear Strength | 49°C | Cohesive Failure | ||||
| 550 psi | Overlap Shear Strength | 89°C | Cohesive Failure | ||||
| 50 psi | Overlap Shear Strength | 600 sec | 23°C | ||||
| 1,500 psi | Overlap Shear Strength | 1,200 sec | 23°C | ||||
| 2,250 psi | Overlap Shear Strength | 3,600 sec | 23°C | ||||
| 2,750 psi | Overlap Shear Strength | 7,200 sec | 23°C | ||||
| 2,950 psi | Overlap Shear Strength | 14,400 sec | 23°C | ||||
| 3,350 psi | Overlap Shear Strength | 28,800 sec | 23°C | ||||
| 3,600 psi | Overlap Shear Strength | 86,400 sec | 23°C |
| Peel Strength | Type | Cure Time | Cure Temperature | Substrate | Test Temperature | Test Method |
|---|---|---|---|---|---|---|
| Excellent | ||||||
| 30 piw | T-Peel strength | 360 min | 24°C | Etched Al | 23°C | Peel tests (ASTM D1876-61T) on FPL etched, 0.032" gauge aluminum, with a .017" bondline thickness. Jaw separation rate 20"/min. All bonds were allowed to cure for at least 6 hours at 75°F (24°C) before testing. |
Message sent - We'll get back shortly
Message sent - We'll get back shortly! Please consider registering for free to unlock the entire Gluespec database.
Great! Contact us if you have any additional questions.
You will lose your saved materials unless you register. Please register.
| Manufacturer | Material | Remove |
|---|
Things you can do with checked materials:
| Name | Save Date | View |
|---|
Need help? Our knowledgeable experts help you achieve your goals by giving you application insights. They are available personally to help you before, during or after your search.
