-
Description for 3M F9469 PC
Utilize the high performance of adhesive 100MP, which has excellent long term holding power with much higher adhesion strength than typical pressure sensitive adhesive systems.Chemical Resistance Chemical Resistance: No apparent degradation when exposed to splash testing of many common solvents and fluids including gasoline, JP-4 fuel, mineral spirits, motor oil, ammonia cleaner, acetone and methyl ethyl ketone Application Type Bond 1 Part or 2 Part 1-Part Material Form Transfer Tape Substrate Aluminum, Ceramic, Glass, Polycarbonate, Unplasticized PVC, Enameled Steel, Stainless Steel, Phenolic, Galvanized Steel, Epoxy, Galvanized Steel, ABS, Aluminum (T-Block), Nickel Plated Steel Industry Many exterior industrial applications Manufacturer 3M Chemistry Acrylic Cure Method Pressure Sensitive Color Transparent Total Thickness (mm) 0.229 High Temperature Resistance (°C) 260, 149 Density (g/cm³) 1.107 -
Technical Data for 3M F9469 PC
Overview
-
Chemical Resistance
- Chemical Resistance : Relative Solvent Resistance - No apparent degradation when exposed to splash testing of many common solvents and fluids including gasoline, JP-4 fuel, mineral spirits, motor oil, ammonia cleaner, acetone and methyl ethyl ketone
-
Application Type
- Adhesive - Bond
-
1 Part or 2 Part
- 1-Part
-
Material Form
- Tape - Transfer Tape
-
Substrate
- Ceramic
- Glass
- Aluminum - Aluminum (T-Block)
- Steel - Enameled Steel, Nickel Plated Steel
- Galvanized - Galvanized Steel
- Polycarbonate
- Polyvinyl chloride (PVC) - Unplasticized PVC
- Phenolic
- Epoxy
- ABS
- Stainless Steel
- Galvanized Steel
-
Industry
- Industrial - Many interior industrial applications, Replace rivets, Spot welds
- Industrial Exterior - Many exterior industrial applications
-
Chemistry
-
Application Method
- Contact
-
Cure Method
- Pressure Sensitive (min) - Pressure Sensitive
-
Color
- Clear / Transparent - Transparent
Specifications
Bond Strength
General Bond Strength (psi) Much higher Peel Strength (piw) 8.0 (lb./in.) Test Method Shear Strength (psi) 80, 1000 (grams) Test Method Tensile Strength (psi) 100 Test Method Tape Properties
Total Thickness (mm) 0.229 Tape Backing 2 mil Aluminum Foil Material Resistance
UV Resistance Excellent UV resistance through outdoor weathering tests and weather-O-meter tests High Temperature Resistance (°C) 260, 149 Test Method Conductivity
Insulation Resistance (O) >1e6 (megaohms/in2) Test Method Thermal Conductivity (W/m°K) 0.16 Test Method Other Properties
Coefficient of Thermal Expansion (CTE) 770e-6 (mm/mm/°C) Density (g/cm³) 1.107 Business Information
Shelf Life Details Store at room temperature conditions of 70°F (21°C) and 50% relative humidity.;If stored properly, product retains its performance and properties for 18 months from date of shipment. If the products have been exposed to severe weather conditions, we suggest to precondition the products at the above storage conditions for at least 24 hours before using them., Humidity controlled storage: 60° to 80°F (16° to 27°C) and 40-60% R.H. If stored properly, product retains its performance and properties for 24 months from date of manufacture. If the products have been exposed to severe weather conditions, we suggest to precondition the products at the above storage conditions for at least 24 hours before using them. Shelf Life Temperature (°F) 70, 140 to 176 Shelf Life Type From date of shipment., From date of manufacture Shelf Life (mon) 18, 24 -
-
Best Practices for 3M F9469 PC
-
Surface Preparation
To obtain optimum adhesion, the bonding surfaces must be clean, dry, and well unified. Some typical surface cleaning solvents are isopropyl alcohol/water mixture or heptane.
Note: Be sure to follow the manufacturer’s precautions and directions for use when using solvents.
-
Application
Bond strength is dependent upon the amount of adhesive-to-surface contact developed. Firm application pressure helps develop better adhesive contact and improve bond strength.
Initial tape application to surfaces at temperatures below 50°F (10°C) is not recommended because the adhesive becomes too firm to adhere readily. However, once properly applied, low temperature holding is generally satisfactory.
-
-
Comparable Materials for 3M F9469 PC
Spec Engine® Results
-
4611(3M)Dark gray, closed-cell acrylic foam carrier • High temperature resistance• Apply as low as 50°F (10°C) • UL 746C
-
Ultra High Temperature 100 HT Adhesive Transfer Tape 9085UV(3M)
A high performance and low outgassing adhesive system having excellent heat resistance in high temperature environments.
-
Ultra High Temperature 100 HT Adhesive Transfer Tape 9082(3M)
A high performance and low outgassing adhesive system having excellent heat resistance in high temperature environments.
- Compare All
-
Popular Articles
What Projects Require Custom Adhesive Formulations and Why?
Read Article
Testing the effectiveness of surface treatments
Read Article
Plastic Bonding with Adhesives - Considerations Q&A
Read Article
Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation
Read ArticleSponsored Articles
Unique Advantages of Contact Adhesives
Read Article
Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials
Read Article
Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:
Read Article
Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive
Read ArticleFeatured Ads
Peel Strength Test Methods
| Peel Strength | Substrate | Test Method |
|---|---|---|
| 8.0 (lb./in.) | Stainless Steel | ASTM D3330 |
Tensile Strength Test Methods
| Tensile Strength | Substrate | Test Method |
|---|---|---|
| 100 psi | Aluminum | ASTM D897 |
Shear Strength Test Methods
| Shear Strength | Type | Substrate | Test Time | Test Temperature | Test Method |
|---|---|---|---|---|---|
| 80 psi | Dynamic Overlap Shear | Stainless Steel | ASTM D1002 | ||
| 1000 (grams) | Static shear strength | Stainless Steel | >600,000 sec | <149°C | ASTM D-3654 |
High Temperature Resistance Test Methods
| High Temperature Resistance | Test Method |
|---|---|
| 260°C | Short Term Temperature Tolerance, 4-hour conditioning at the indicated temperature with 100 g static load. |
| 149°C | Long Term Temperature Tolerance, Maximum temperature where tape supports 250 g in static shear for 10,000 minutes. |
Insulation Resistance Test Methods
| Insulation Resistance | Test Method |
|---|---|
| >1e6 (megaohms/in2) | ASTM D1000 |
Thermal Conductivity Test Methods
| Thermal Conductivity | Test Method |
|---|---|
| 0.16 W/m°K | ASTM C-177 |
