3M Fastbond Contact Adhesive 30NF Datasheet 3M Fastbond Contact Adhesive 30NF

CONTACT REP
Information provided by Gluespec

  • Description for 3M Fastbond Contact Adhesive 30NF

    Non-flammable in the wet state, heat resistant and sprayable contact adhesive. It bonds most foamed plastics, plastic laminate, wood, plywood, and canvas to themselves and to each other.

    *See Terms of Use Below

    Chemical Resistance Chemical Resistance: Methanol <2%, Chemical Resistance: Fluid Resistance: Water, Chemical Resistance: Toluene <3%
    Application Type Bond
    1 Part or 2 Part 1-Part
    Material Form Liquid
    Substrate Fabric, Nylon, Most foamed plastics, Steel, Particle board, Foam, Polyethylene, Non-porous surfaces, Plastic laminate, Plywood, Most foamed plastics, Wood, 1/8” Birch , Wood veneers
    Manufacturer 3M
    Chemistry Polychloroprene, Non-flammable
    Cure Method Solvent, Pressure sensitive
    Coverage 680 (sq ft/gal)
    Viscosity (cPs) 200 to 750
    Color Green when wet, Darker green when dry, Neutral, Clear (Dry), White (Wet)
    High Temperature Resistance (°C) 107, 82, Heat resistant
    Low Temperature Resistance (°C) -34
    Density (g/cm³) 8.9 to 9.3 (weight (lbs/gal))
    Key Specifications ANSI (American National Standards Institute): HP 1983: ANSI/HPMA HP 1983 for Type II, Recognized under the Component Program Underwriter’s Laboratories, Inc. Component Recognition Program Guide GSRJ2, File R14485, Door Construction Materials, Mil-Spec (United States Military Standard): A-24179A: MIL-A-24179A, Type I, Registered to ISO 9001 standards

  • Technical Data for 3M Fastbond Contact Adhesive 30NF

    *See Terms of Use Below

    Overview
    • Chemical Resistance
      • Chemical Resistance : Fluid Resistance : Water Resistance - Water
      • Chemical Resistance : Relative Solvent Resistance - Methanol <2%, Toluene <3%
    • Application Type
    • 1 Part or 2 Part
      • 1-Part
    • Material Form
      • Liquid
    • Substrate
      • Foam - Most foamed plastics
      • Non-Porous Substrates - Non-porous surfaces
      • Steel
      • Plastic - Most foamed plastics, Plastic laminate
      • Nylon
      • Polyethylene (LDPE, HDPE) - Polyethylene
      • Wood - Particle board, Plywood, 1/8” Birch , Wood veneers
      • Fabric
      • Other - Canvas
    • Industry
    • Chemistry
      • Non-flammable
      • Other - Polychloroprene
    • Application Method
      • Roll - Roll coating
      • Brush
      • Contact
      • Spray - Sprayable, Airless spray, Air atomizing spray equipment
      • Other - Pressure pot, Pumping equipment, Filter, Hoses
    • Cure Method
      • Pressure Sensitive (min) - Pressure sensitive
      • Solvent
    • Color
      • Clear / Transparent - Clear (Dry)
      • Green - Green when wet, Darker green when dry
      • White - White (Wet)
      • Other - Neutral
    • Key Specifications
      • UL (Underwriters Laboratory), ULC (Underwriters Laboratories of Canada), NFPA (National Fire Protection Association) - Recognized under the Component Program Underwriter’s Laboratories, Inc. Component Recognition Program Guide GSRJ2, File R14485, Door Construction Materials
      • International Organization for Standardization - Registered to ISO 9001 standards
      • ANSI (American National Standards Institute) : HP 1983 : Type II - ANSI/HPMA HP 1983 for Type II
      • Mil-Spec (United States Military Standard) : A-24179A : Type I - MIL-A-24179A, Type I
    Specifications
    Cure Specs
    Coverage 680 (sq ft/gal) Test Method
    Viscosity (cPs) 200 to 750 Test Method
    Dry Time (min) 30
    Bond Strength
    General Bond Strength (psi) High immediate bond strength
    Peel Strength (piw) 25, 35, 30, 20, 20, 15, 5, 10, 10, 400 (oz/in), 560 (oz/in), 480 (oz/in), 320 (oz/in), 320 (oz/in), 240 (oz/in), 80 (oz/in), 160 (oz/in), 160 (oz/in) Test Method
    Shear Strength (psi) 1100 (lb/in²), 450 (lb/in²), 60 (lb/in²), 30 (lb/in²), 40 (lb/in²), 265 (lb/in²), 315 (lb/in²), 305 (lb/in²), 285 (lb/in²), 130 (lb/in²), 140 (lb/in²), 150 (lb/in²), 125 (lb/in²), 30 (lb/in²), 80 (lb/in²), 75 (lb/in²), 50 (lb/in²) Test Method
    Tensile Strength (psi) 113 (lb/in²), 55 (lb/in²), 33 (lb/in²), 27 (lb/in²) Test Method
    Material Resistance
    High Temperature Resistance (°C) 107, 82, Heat resistant
    Low Temperature Resistance (°C) -34
    Other Properties
    % Solids (%) 47 to 51 Test Method
    Density (g/cm³) 8.9 to 9.3 (weight (lbs/gal))
    Business Information
    Shelf Life Details Best storage temperature is 60-80°F (16-27°C) for maximum storage life. Higher temperatures reduce normal storage life. Lower temperatures cause increased viscosity of a temporary nature. These water-based contact adhesives will become unusable with prolonged storage below 40°F (4°C). Rotate stock on a “first-in, first-out” basis. When stored at the recommended temperature in the original, unopened container, these products have a shelf life of 21 months from date of manufacture.
    Shelf Life Temperature (°F) 60 to 80
    Shelf Life (mon) 21
    Not Good For
    Don't Use For Un-backed wood veneers
    Don't Use With Drywall laminating, Metal surfaces (unless metal surfaces are completely dried by force drying and protected from moisture), Rubber lined hose, “Rubber” lined hose, Copper, Aluminum, Brass, Steel fittings

  • Best Practices for 3M Fastbond Contact Adhesive 30NF

    *See Terms of Use Below

    1. Surface Preparation

      Surfaces must be clean, dry and dust free. Wiping with a solvent such as 3M™ Solvent No. 3* will aid in removing oil and dirt. Temperature of adhesive and surfaces during fabrication should be at least 65°F (18°C). If used for decorative plastic laminates, the laminate should have reached moisture equilibrium for the shop conditions.

      When using solvents, extinguish all ignition sources, including pilot lights, and follow the manufacturer’s precautions and directions for use.

    2. Application

      When bonding wood veneers, success is dependent on many variables such as environmental conditions, bonding process, type of base material, type of veneer, adhesive type and top coat finishing systems to name a few. For un-backed wood veneers, water based contact adhesives are not recommended. It is the user’s responsibility to thoroughly test any adhesive for its suitability in bonding wood veneers. It is also recommended to follow the veneer manufacturers recommendation and industry guidelines.

      Apply a uniform, generous coat of adhesive to both surfaces with a nylon brush, roller (texturing type), or spray. One coat is usually sufficient on most surfaces. Dull spots when dry indicate insufficient adhesive. Very porous material may require more than one coat. (Allow adhesive to dry completely between coats.) A uniform, glossy film indicates sufficient adhesive.

      Coverage is dependent upon porosity of the substrate and the method by which the adhesive is applied. Use 3.0-3.5 gms/ft2 of dry adhesive per surface for wood, particle board and high pressure laminates with the adhesive applied by spray or roller. More adhesive (lower coverage) is recommended if very soft wood, fabrics, foams, etc. are to be bonded, or if the adhesive is applied by brushing.

      Assembly: Spacers, such as dowels or strips of laminate, may be used to help prevent premature adhesive to adhesive contact and bonding prior to positioning. Slide out the spacers and apply uniform pressure, working toward the edges. A 3 in. wide (maximum) roller with maximum body pressure should be used to help ensure adequate contact and bonding, especially on edges. Bonded assemblies may be machined, trimmed, etc. immediately after bonding. The use of a pinch or nip roll is preferred for optimum performance.

      Handling/Application Information (continued): (1) Working Temperature: The adhesive and both surfaces to be bonded should be 65°F (18°C) or above at the time of bonding. After storage at low temperature and before using, the adhesive must be warmed to room temperature. Do not place in oven or on stove

      bring to temperature by placing in a warm room. If this is not done, the open time and other working properties of the adhesive may be adversely affected. (2) Use Enough Adhesive: It is important to remember that it is difficult to use too much adhesive, but you can have problems if you don’t use enough. 3M™ Fastbond™ Contact Adhesive 30 must be applied to both surfaces. Adhesive can be applied by spray (see Application Equipment Suggestions), brush or a texturing type roller., Non-porous surfaces should require only one coat, while porous surfaces may require two coats. Wherever you use more than one coat, be sure to let the adhesive dry completely between coats. Hardwoods, tempered hardboard and decorative laminates are non-porous. Soft woods, untempered hardboard, plywood and plaster are typical porous surfaces which may require two coats.

      Note: 3M water-dispersed contact adhesives should never be thinned.

      Let Adhesive Dry Completely: Under normal temperature and humidity conditions, Fastbond contact adhesive 30 will dry in approximately 30 minutes. In very warm, low humidity conditions, drying may take as little as 10-15 minutes. Lower temperatures and higher humidity mean slower drying. When the adhesive coating completely loses its milky appearance and becomes clear it is ready to bond. You have four (4) hours after the adhesive is dry in which to complete the bonding job. You can bond as soon as it is dry, but the longer you wait the stronger the initial bond will be.

      To speed drying, infrared heat lamps may be used. When force drying is used, assembly and bonding must be completed while one or both of the bonding surfaces is warm. If both surfaces are cold, reheat either or both before bonding., If your two surfaces do not grab onto each other immediately when brought into contact, the adhesive has dried too long or not enough adhesive was applied. In either case, another coat of adhesive over each surface will remedy the problem.

      Apply Pressure Thoroughly: Bonding is immediate upon contact. Sustained pressure is not required, but good uniform pressure must be applied to every square inch of the surface. Apply pressure by using heavy body pressure on a small (not over 3”) hand “J”-roller. The use of a pinch roll is preferred for optimum performance.

      Note: Rolling pins and other wide rollers are unsatisfactory because they bridge low spots and because they distribute the pressure over too large an area.

      Assembling: Position the surfaces carefully before assembly. No adjustment is possible after the adhesive films make contact. Use the paper slip sheet method or spacers to position large pieces.

      Finishing: Bonded assemblies can be machined, trimmed and finished immediately after bonding.

      Cleaning: Brushes or rollers which are to be reused should be wrapped with plastic wrap to keep adhesive wet as complete cleaning is difficult.

      Application Equipment: Note: Appropriate application equipment can enhance adhesive performance. We suggest the following application equipment for the user’s evaluation in light of the user’s particular purpose and method of application.

      1. Air Atomizing Spray Equipment

      To measure fluid flow: Pressurize fluid source only

      pull trigger

      flow material into measuring device for 60 seconds

      increase or decrease fluid source pressure to obtain desired fluid flow.

      Note: Low pressure, air operated piston pumps should not be used with these products.

      2. Pressure Pot: Polyethylene liner.

    3. Curing

      Drying Time: The adhesive dries sufficiently in 30 minutes under normal temperatures and humidities to make bonds. High humidity will slow the drying

      high temperature will speed the drying. After the adhesive is dry the bond must be completed within four hours.

    4. Clean-Up

      If adhesive has not dried, clean equipment with water containing a small amount of detergent.** Adhesive cannot be cleaned off rollers or brushes after it has dried.

      Cleaning solution: One pint of cleaner to five gallons of water. Flush with clean water.

    5. Testing

      3M™ Fastbond™ Contact Adhesive 30 has been tested and approved for use by the Woodwork Institute of California under the provisions of ANSI/HPMA HP 1983 for Type II adhesive and the heat resistance test set forth in its Manual of Millwork.

  • Comparable Materials for 3M Fastbond Contact Adhesive 30NF

    *See Terms of Use Below

    Spec Engine® Results

    Closest Results from this Manufacturer

    • 3M
      Aluminum Foil Tape 1120(3M)

      Commonly used for EMI/RFI shielding applications in the electronics industry and for static charge draining, seaming shielded rooms, cable wrapping and surface contact to non-solderable materials.

    • 3M
      Copper Foil Shielding Tape 1125(3M)

      • Non-conductive acrylic adhesive • Copper color • Flat copper foil backing • Commonly used for EMI/RFI shielding applications • Flame Retardant • Commonly used for cable wrapping

    • Compare All
  Download Technical Data Sheet   Save This Material   Compare View Saved Items

Popular Articles

Testing the effectiveness of surface treatments

Read Article

Lightweighting drives automotive adhesives demand

Read Article

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Read Article

6 objects held together by adhesives you probably can't live without

Read Article

Sponsored Articles

Unique Advantages of Contact Adhesives

Read Article

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Read Article

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Read Article

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Read Article

Featured Ads

Top Catalog Pages for 3M Fastbond Contact Adhesive 30NF

All 3M Materials
View Now
Contact Adhesives
View Now

Gluespec Poll

Who do you read or follow for engineering news and entertainment?
Viscosity Test Methods
Viscosity Test Method Temperature
200 to 750 cPs Brookfield Viscometer, RVF #2 sp. @ 20 rpm 27°C
Coverage Test Methods
Coverage Test Method
680 (sq ft/gal) Notes: @ 3 g/ft² dry
Peel Strength Test Methods
Peel Strength Type Cure Time Cure Temperature Substrate Test Time Test Temperature Test Method
25 piw T-Peel strength 1,440 min 24°C Canvas 24°C The following technical information and data should be considered representative or typical only and should not be used for specification purposes.
35 piw T-Peel strength 4,320 min 24°C Canvas 24°C The following technical information and data should be considered representative or typical only and should not be used for specification purposes.
30 piw T-Peel strength 7,200 min 24°C Canvas 24°C The following technical information and data should be considered representative or typical only and should not be used for specification purposes.
20 piw T-Peel strength 10,080 min 24°C Canvas 24°C The following technical information and data should be considered representative or typical only and should not be used for specification purposes.
20 piw T-Peel strength 20,160 min 24°C Canvas 24°C The following technical information and data should be considered representative or typical only and should not be used for specification purposes.
15 piw T-Peel strength 30,240 min 24°C Canvas 24°C The following technical information and data should be considered representative or typical only and should not be used for specification purposes.
5 piw T-Peel strength 30,240 min -37°C Canvas -37°C The following technical information and data should be considered representative or typical only and should not be used for specification purposes.
10 piw T-Peel strength 30,240 min 66°C Canvas 66°C The following technical information and data should be considered representative or typical only and should not be used for specification purposes.
10 piw T-Peel strength 30,240 min 82°C Canvas 82°C The following technical information and data should be considered representative or typical only and should not be used for specification purposes.
400 (oz/in) 1,440 min 23°C Canvas to steel 180° Peel Adhesion, Dwell, Environmental Condition: 50%RH
560 (oz/in) 4,320 min 23°C Canvas to steel 180° Peel Adhesion, Dwell, Environmental Condition: 50%RH
480 (oz/in) 7,200 min 23°C Canvas to steel 180° Peel Adhesion, Dwell, Environmental Condition: 50%RH
320 (oz/in) 10,080 min 23°C Canvas to steel 180° Peel Adhesion, Dwell, Environmental Condition: 50%RH
320 (oz/in) 20,160 min 23°C Canvas to steel 180° Peel Adhesion, Dwell, Environmental Condition: 50%RH
240 (oz/in) 30,240 min 23°C Canvas to steel 180° Peel Adhesion, Dwell, Environmental Condition: 50%RH
80 (oz/in) 30,240 min -34°C Canvas to steel 180° Peel Adhesion, Dwell, Environmental Condition: 50%RH
160 (oz/in) 30,240 min 66°C Canvas to steel 180° Peel Adhesion, Dwell, Environmental Condition: 50%RH
160 (oz/in) 30,240 min 82°C Canvas to steel 180° Peel Adhesion, Dwell, Environmental Condition: 50%RH
Tensile Strength Test Methods
Tensile Strength Substrate Test Temperature Test Method
113 (lb/in²) High pressure laminate/particle board (Particle board failure) 20 to 25°C Notes: High pressure laminate/particle board. Test speed = 0.05 in./min.
55 (lb/in²) High pressure laminate/particle board 66°C Notes: High pressure laminate/particle board. Test speed = 0.05 in./min.
33 (lb/in²) High pressure laminate/particle board 82°C Notes: High pressure laminate/particle board. Test speed = 0.05 in./min.
27 (lb/in²) High pressure laminate/particle board 93°C Notes: High pressure laminate/particle board. Test speed = 0.05 in./min.
Shear Strength Test Methods
Shear Strength Type Cure Time Substrate Test Temperature Test Method
1100 (lb/in²) Overlap shear strength 1/8” Birch 1/8” Birch -37°C
450 (lb/in²) Overlap shear strength 1/8” Birch 1/8” Birch 24°C
60 (lb/in²) Overlap shear strength 1/8” Birch 1/8” Birch 82°C
30 (lb/in²) Overlap shear strength 1/8” Birch 1/8” Birch 93°C
40 (lb/in²) Overlap shear strength 1/8” Birch 1/8” Birch 107°C
265 (lb/in²) Static shear Birch to high-pressure laminate 20 to 25°C Room temperature Notes: Laminate sprayed with adhesive, dried, and stored @RT for the given time (free of dust and dirt). Adhesive sprayed to birch and dried for 10 min. Pinch roller bond samples and aged 3 weeks. Adhesive can be activated with certain contact adhesives.
315 (lb/in²) Static shear 129,600 min Birch to high-pressure laminate 20 to 25°C Room temperature Notes: Laminate sprayed with adhesive, dried, and stored @RT for the given time (free of dust and dirt). Adhesive sprayed to birch and dried for 10 min. Pinch roller bond samples and aged 3 weeks. Adhesive can be activated with certain contact adhesives.
305 (lb/in²) Static shear 259,200 min Birch to high-pressure laminate 20 to 25°C Room temperature Notes: Laminate sprayed with adhesive, dried, and stored @RT for the given time (free of dust and dirt). Adhesive sprayed to birch and dried for 10 min. Pinch roller bond samples and aged 3 weeks. Adhesive can be activated with certain contact adhesives.
285 (lb/in²) Static shear 388,800 min Birch to high-pressure laminate 20 to 25°C Room temperature Notes: Laminate sprayed with adhesive, dried, and stored @RT for the given time (free of dust and dirt). Adhesive sprayed to birch and dried for 10 min. Pinch roller bond samples and aged 3 weeks. Adhesive can be activated with certain contact adhesives.
130 (lb/in²) Static shear Birch to high-pressure laminate 66°C Room temperature Notes: Laminate sprayed with adhesive, dried, and stored @RT for the given time (free of dust and dirt). Adhesive sprayed to birch and dried for 10 min. Pinch roller bond samples and aged 3 weeks. Adhesive can be activated with certain contact adhesives.
140 (lb/in²) Static shear 129,600 min Birch to high-pressure laminate 66°C Room temperature Notes: Laminate sprayed with adhesive, dried, and stored @RT for the given time (free of dust and dirt). Adhesive sprayed to birch and dried for 10 min. Pinch roller bond samples and aged 3 weeks. Adhesive can be activated with certain contact adhesives.
150 (lb/in²) Static shear 259,200 min Birch to high-pressure laminate 66°C Room temperature Notes: Laminate sprayed with adhesive, dried, and stored @RT for the given time (free of dust and dirt). Adhesive sprayed to birch and dried for 10 min. Pinch roller bond samples and aged 3 weeks. Adhesive can be activated with certain contact adhesives.
125 (lb/in²) Static shear 388,800 min Birch to high-pressure laminate 66°C Room temperature Notes: Laminate sprayed with adhesive, dried, and stored @RT for the given time (free of dust and dirt). Adhesive sprayed to birch and dried for 10 min. Pinch roller bond samples and aged 3 weeks. Adhesive can be activated with certain contact adhesives.
30 (lb/in²) Static shear Birch to high-pressure laminate 82°C Notes: Laminate sprayed with adhesive, dried, and stored @RT for the given time (free of dust and dirt). Adhesive sprayed to birch and dried for 10 min. Pinch roller bond samples and aged 3 weeks. Adhesive can be activated with certain contact adhesives.
80 (lb/in²) Static shear 129,600 min Birch to high-pressure laminate 82°C Notes: Laminate sprayed with adhesive, dried, and stored @RT for the given time (free of dust and dirt). Adhesive sprayed to birch and dried for 10 min. Pinch roller bond samples and aged 3 weeks. Adhesive can be activated with certain contact adhesives.
75 (lb/in²) Static shear 259,200 min Birch to high-pressure laminate 82°C Notes: Laminate sprayed with adhesive, dried, and stored @RT for the given time (free of dust and dirt). Adhesive sprayed to birch and dried for 10 min. Pinch roller bond samples and aged 3 weeks. Adhesive can be activated with certain contact adhesives.
50 (lb/in²) Static shear 388,800 min Birch to high-pressure laminate 82°C Notes: Laminate sprayed with adhesive, dried, and stored @RT for the given time (free of dust and dirt). Adhesive sprayed to birch and dried for 10 min. Pinch roller bond samples and aged 3 weeks. Adhesive can be activated with certain contact adhesives.
% Solids Test Methods
% Solids Test Method
47 to 51 % By weight