3M PR10 Rite-Lok Cyanoacrylate

3M PR10 Rite-Lok Cyanoacrylate Datasheet
  • Description for 3M PR10 Rite-Lok Cyanoacrylate

    Formulated with a unique elastomer that maximizes impact, vibration, peel, and thermal cycling resistance while providing tough flexible bonds.

    *See Terms of Use Below

    Application Type Bond
    1 Part or 2 Part 1 Part
    Material Form Liquid
    Substrate dissimilar materials, porous substrate surfaces, Polyethylene, Paper, Low surface energy plastics, polypropylene, Rubber Toughened, Low surface energy plastics
    Manufacturer 3M
    Chemistry Rubber Toughened Cyanoacrylate, Ethyl Hybrid
    Cure Method Moisture
    Viscosity (cPs) high, 1,000 to 3,000, 5,000 to 10,000
    Color Black
    Chemical Resistance Excellent, Most oils
    Relative Solvent Resistance Chemical Resistance: Excelent Solvent resistance
    High Temperature Resistance (°C) Thermal cycling
  • Technical Data for 3M PR10 Rite-Lok Cyanoacrylate

    Overview
    • Application Type
    • 1 Part or 2 Part
      • 1 Part or 2 Part - 1 Part
    • Material Form
      • Liquid
    • Substrate
      • Porous Substrates - porous substrate surfaces
      • Low Surface Energy - Low surface energy plastics
      • Dissimilar Substrates - dissimilar materials
      • Plastic - Low surface energy plastics
      • Polyethylene (LDPE, HDPE) - Polyethylene
      • Polypropylene
      • Rubber - Rubber Toughened
      • Paper
      • Other - flexible substrates, Acidic surfaces, Leather
    • Chemistry
      • Toughened - Rubber Toughened Cyanoacrylate
      • Other - Ethyl Hybrid
    • Application Method
      • Other - Hand applied
    • Cure Method
      • Moisture / Condensation Cure - Moisture
    • Color
      • Black
    Specifications
    Cure Specs
    Viscosity (cPs) high, 1,000 to 3,000, 5,000 to 10,000 Test Method
    Fixture or Handling Strength Time (min) 0.33 to 1.50
    Set Time (min) very fast
    Bond Strength
    Peel Strength (piw) Peel Resistance
    Shear Strength (psi) 1,300 Test Method
    Impact Strength (psi) Impact strength
    Material Resistance
    Chemical Resistance Excellent, Most oils
    Relative Solvent Resistance Chemical Resistance: Excelent Solvent resistance
    High Temperature Resistance (°C) Thermal cycling
    Impact Resistance Impact resistance
    Vibration Resistance/Shock Resistance Vibration resistance
    Other Properties
    Specific Gravity 1.100
    Business Information
    Shelf Life Details For short term storage (<30 days), keep adhesive in a cool (60°F to 80°F [16°C to 27°C]), dry place out of direct sunlight. Keep containers tightly covered and free of moisture. Refrigeration (40°F [4°C]) gives optimum long term storage stability.;Rite-Lok™ Rubber Toughened Instant Adhesives can be expected to have a shelf life of one year from the date of shipment from 3M when stored under refrigerated conditions.
    Shelf Life Temperature (°F) 60 to 80, 40
    Shelf Life Type From the date of shipment
    Shelf Life (mon) 12
  • Best Practices for 3M PR10 Rite-Lok Cyanoacrylate

    *See Terms of Use Below

    1. Surface Preparation

      For optimum strength structural bonds, paint, oxide films, oils, dust, mold release agents, and all other surface contaminants must be completely removed. However, the amount of surface preparation depends on the required bond strength and the environmental aging resistance desired by the user. Typical quick surface preparation would include wiping with a clean solvent (such as isopropyl alcohol), abrading the surface with a clean fine abrasive, and then wiping again with a clean solvent to remove loose particles. Note: When using solvents, extinguish all ignition sources, including pilot lights, and follow the manufacturer’s precautions and directions for use.

      Ensure that parts are clean, dry, and free from oil and grease.

      A Rite lok™ Instant Adhesive Activator may be required if there are bonding gaps or porous substrate surfaces, if substrates are low surface energy plastics (e.g., polyethylene, polypropylene ) or if substrates have acidic surfaces (e.g., paper, leather).

    2. Application

      Bond speed is typically very fast so ensure that parts are properly aligned before dispensing.

      Product is normally hand applied from the bottle. Apply sparingly to one surface and press parts firmly together until handling strength is achieved. As a general rule, as little cyanoacrylate as possible should be used. Over application will result in slower cure speed and lower bond strength.

    3. Curing

      Full bond strength will typically be achieved within a 24 hour cure time.

      Low humidity or low temperature conditions will slow down the cure rate.

      After curing, Rite-Lok™ Rubber Toughened Instant Adhesive bonds are suitable for use at temperatures up to 200F (93°C) continuously, intermittently up to 250°F (121°C). At 220°F (105°C) the bond will be approximately 40% of the strength at room temperature.

      Cyanoacrylate bond resistance to most oils and solvents is excellent. Long term humidity, moisture, or water immersion may affect the strength of a cured cyanoacrylate bond depending on the substrates and the bond gap. Testing is recommended to evaluate the effect.

  • Comparable Materials for 3M PR10 Rite-Lok Cyanoacrylate

    *See Terms of Use Below

    Spec Engine® Results

    Closest Results from this Manufacturer

Questions about this material?

Get personal assistance with your specific application needs.

Your Profile Edit
  1. 43d0568e-6fcc-4907-9c49-3f49898e0c03
  2. 43d0568e-6fcc-4907-9c49-3f49898e0c03

Popular Articles

Lightweighting drives automotive adhesives demand

Read Article

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Read Article

6 objects held together by adhesives you probably can't live without

Read Article

Testing the effectiveness of surface treatments

Read Article

Sponsored Articles

Unique Advantages of Contact Adhesives

Read Article

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Read Article

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Read Article

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Read Article
Information provided by Gluespec

Why Register?

  • View Technical Details
  • View Test Methods
  • View Key Specifications
  • View Similar Materials
  • Save your Project Searches

Already registered? Sign in.

Questions? Learn more about Gluespec

Gluespec Poll

When you're researching or sourcing materials online, what device are you using?
Viscosity Test Methods
Viscosity Test Method
high
1,000 to 3,000 cPs Brookfield RVT, #3 spindle @ 20 rpm
5,000 to 10,000 cPs Brookfield RVT, #3 spindle @ 2.5 rpm.
Shear Strength Test Methods
Shear Strength Type Test Method
1,300 psi Overlap Shear Strength ASTM D1002