3M PR600B Rite-Lok Cyanoacrylate Datasheet 3M PR600B Rite-Lok Cyanoacrylate

Information provided by Gluespec
  • Description for 3M PR600B Rite-Lok Cyanoacrylate

    Designed to give exceptional performance on difficult-to-bond plastic and rubber substrates.

    *See Terms of Use Below

    Chemical Resistance Excellent, Chemical Resistance: Excelent Solvent resistance, Most oils
    Application Type Bond, Adhesive: Instant Adhesives
    1 Part or 2 Part 1-Part
    Material Form Liquid
    Substrate composite, in combination with metal, Nylon, Paper, difficult-to-bond plastic, polypropylene, heavily plasticized PVC, rubber, porous substrate surfaces, polyethylene, EPDM, Low surface energy plastics, ABS, Low surface energy plastics
    Manufacturer 3M
    Chemistry Cyanoacrylate, Ethyl Hybrid
    Cure Method Moisture
    Cure Time (min) 1,440
    Viscosity (cPs) 510 to 660
    Color Black
    High Temperature Resistance (°C) 82
    Low Temperature Resistance (°C) -54
  • Technical Data for 3M PR600B Rite-Lok Cyanoacrylate

    Overview
    • Chemical Resistance
      • Chemical Resistance - Excellent, Most oils
      • Chemical Resistance : Relative Solvent Resistance - Excelent Solvent resistance
    • Application Type
    • 1 Part or 2 Part
      • 1-Part
    • Material Form
      • Liquid
    • Substrate
      • Porous Substrates - porous substrate surfaces
      • Low Surface Energy - Low surface energy plastics
      • Metal - in combination with metal
      • Plastic - difficult-to-bond plastic, Low surface energy plastics
      • Nylon
      • Polypropylene
      • Polyvinyl chloride (PVC) - heavily plasticized PVC
      • Polyethylene (LDPE, HDPE) - polyethylene
      • ABS
      • Rubber
      • EPM/EPDM - EPDM
      • Composites - composite
      • Paper
      • Other - like substrates, Santoprene, Viton, common substrates, acidic surfaces, leather
    • Chemistry
    • Application Method
      • Other - Hand applied
    • Cure Method
      • Moisture / Condensation Cure - Moisture
    • Color
      • Black
    Specifications
    Cure Specs
    Cure Time (min) 1,440
    Viscosity (cPs) 510 to 660 Test Method
    Fixture or Handling Strength Time (min) 0.07 to 0.42
    Material Resistance
    High Temperature Resistance (°C) 82
    Low Temperature Resistance (°C) -54
    Other Properties
    Specific Gravity 1.070
    Business Information
    Shelf Life Details Storage: For short term storage (<30 days), keep adhesive in a cool (60°F to 80°F [16°C to 27°C]), dry place out of direct sunlight. Keep containers tightly covered and free of moisture. Refrigeration (40°F [4°C]) gives optimum long term storage stability.;3M™ Scotch-Weld™ Plastic and Rubber Instant Adhesives can be expected to have a shelf life of one year from the date of shipment from 3M when stored under refrigerated conditions.
    Shelf Life Temperature (°F) 140 to 176, 40
    Shelf Life Type From the date of shipment
    Shelf Life (mon) 12
  • Best Practices for 3M PR600B Rite-Lok Cyanoacrylate

    *See Terms of Use Below

    1. Surface Preparation

      For optimum strength structural bonds, paint, oxide films, oils, dust, mold release agents, and all other surface contaminants must be completely removed. However, the amount of surface preparation depends on the required bond strength and the environmental aging resistance desired by the user. Typical quick surface preparation would include wiping with a clean solvent (such as isopropyl alcohol), abrading the surface with a clean fine abrasive, and then wiping again with a clean solvent to remove loose particles.

      Note: When using solvents, extinguish all ignition sources, including pilot lights, and follow the manufacturer’s precautions and directions for use.

      Ensure that parts are clean, dry, and free from oil and grease.

      A Instant Adhesive Activator may be required if there are bonding gaps or porous substrate surfaces, if substrates are low surface energy plastics (e.g., polyethylene, polypropylene) or if substrates have acidic surfaces (e.g., paper, leather).

    2. Application

      Bond speed is typically very fast so ensure that parts are properly aligned before dispensing.

      Product is normally hand applied from the bottle. Apply sparingly to one surface and press parts firmly together until handling strength is achieved. As a general rule, as little cyanoacrylate as possible should be used. Over application will result in slower cure speed and lower bond strength.

    3. Curing

      Full bond strength will typically be achieved within a 24 hour cure time.

      Low humidity or low temperature conditions will slow down the cure rate

      After curing, 3M™ Scotch-Weld™ Plastic and Rubber Instant Adhesive bonds are suitable for use up to about 180°F (82°C). At 180°F (82°C) the bonds will be approximately 70% of the strength at room temperature and at 212°F (100°C) about 50% of full strength.

      Cyanoacrylate bond resistance to most oils and solvents is excellent. Long term humidity, moisture, or water immersion may affect the strength of a cured cyanoacrylate bond depending on the substrates and the bond gap. Testing is recommended to evaluate the effect

  • Comparable Materials for 3M PR600B Rite-Lok Cyanoacrylate

    *See Terms of Use Below

    Spec Engine® Results

    Closest Results from this Manufacturer

Popular Articles

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Read Article

Cyanoacrylate 202

Read Article

Cyanoacrylate 101

Read Article

Testing the effectiveness of surface treatments

Read Article

Sponsored Articles

Unique Advantages of Contact Adhesives

Read Article

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Read Article

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Read Article

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Read Article

Featured Ads

Top Catalog Pages for 3M PR600B Rite-Lok Cyanoacrylate

Gluespec Poll

What level of expertise do you have in specialty chemicals like adhesives, sealants, conformal coatings, etc.?
Viscosity Test Methods
Viscosity Test Method
510 to 660 cPs Brookfield LVF, Spindle 3 @ 30 rpm.