3M SA24 Rite-Lok Structural Adhesive

3M SA24 Rite-Lok Structural Adhesive Datasheet
CONTACT REP

  • Description for 3M SA24 Rite-Lok Structural Adhesive

    Excellent adhesion to all metals, glass, ferrite, and composite materials. Generally, best applications include flat bond lines. Here tough, durable bonds that perform well under moderate temperatures are formed.<br/>

    *See Terms of Use Below

    Application Type Bond
    1 Part or 2 Part 2 Part
    Material Form Liquid
    Substrate composite materials, ferrite, more absorbent (more porous) surface, Glass, metals, Wood, mirror
    Industry bonded substrates include electronic components, speaker magnets, firearm components
    Manufacturer 3M
    Chemistry Acrylic, Urethane Methacrylate, Urethane Methacrylate, Urethane Methacrylate
    Cure Method 2-Part Cure
    Cure Time (min) 1,440
    Viscosity (cPs) 10,000 to 25,000
    Color Amber

  • Technical Data for 3M SA24 Rite-Lok Structural Adhesive

    *See Terms of Use Below

    Overview
    • Application Type
    • 1 Part or 2 Part
      • 1 Part or 2 Part - 2 Part
    • Material Form
      • Liquid
    • Substrate
    • Industry
    • Chemistry
      • Acrylated Urethane - Urethane Methacrylate
      • Acrylic - Urethane Methacrylate
      • Polyurethane - Urethane Methacrylate
    • Cure Method
      • 2-Part Cure
    • Color
      • Red - Amber
    Specifications
    Cure Specs
    Cure Time (min) 1,440
    Viscosity (cPs) 10,000 to 25,000
    Fixture or Handling Strength Time (min) 1.00, 1.00 to 5.00
    Bond Strength
    Structural/Load-Bearing Structural
    General Bond Strength (psi) Excellent
    Shear Strength (psi) 2,500 Test Method
    Material Resistance
    Impact Resistance impact resistant
    Other Properties
    Specific Gravity 1.130
    Business Information
    Shelf Life Details Storage: Store product in a cool, dry area out of direct sunlight.;Twelve months when stored at 60° to 80°F 16° to 27°C) in the original unopened container.
    Shelf Life Temperature (°F) 140 to 176
    Shelf Life (mon) 12

  • Best Practices for 3M SA24 Rite-Lok Structural Adhesive

    *See Terms of Use Below

    1. Surface Preparation

      For optimum strength surfaces should be clean and free of all surface contaminants including paint, oxide films, oils, dust, mold release agents, etc. However, the amount of surface preparation depends on the required bond strength and the environmental resistance desired by the user. Typical quick surface preparation would include wiping with a clean solvent (such as isopropyl alcohol), abrading the surface with a clean fine abrasive, and then wiping again with a clean solvent to remove loose particles.

      Note: When using solvents, extinguish all ignition sources, including pilot lights, and follow the manufacturer's precautions and directions for use.

      For best results, ensure that parts are clean, dry, and free from oil and grease. However, bonds can still be achieved on 'as received' or slightly oily parts.

    2. Application

      Rite Lok™ structural Acrylic Activator AC380D should be applied to the less absorbent (less porous) substrate. If necessary, it may be applied to both bonding surfaces.

      Rite lok™ structural Acrylic Adhesive should be applied to the more absorbent (more porous) surface in beads or spread as a thin layer using a flat edge.

      The two parts should then be brought together and clamped or held in position to achieve best results.

      Due to its anaerobic nature, any Rite-Lok™ Structural Acrylic Adhesive squeezed outside of the joint will remain soft.

    3. Curing

      Full bond strength will typically be achieved within a 24 hour cure time.

  • Comparable Materials for 3M SA24 Rite-Lok Structural Adhesive

    *See Terms of Use Below

    Spec Engine® Results

    Closest Results from this Manufacturer

    • 3M
      DP8010(3M)

      Acrylic bonds low surface energy polyolefins without surface preparation • Excellent environmental resistance • 1.5-2 hour handling strength • High shear and peel strength acrylic

    • 3M
      DP810(3M)

      Acrylic bonds many metals and plastics without surface prep • Fast strength buildup • Fully cured in 8 hours • Low odor

    • Compare All
  Download Technical Data Sheet   Save This Material Saved Items

Questions about this material?

Get personal assistance with your specific application needs.

Your Profile Edit
  1. 96476c17-3b99-42fa-b8d5-dee5198bc484
  2. 96476c17-3b99-42fa-b8d5-dee5198bc484
Submit

Popular Articles

What Projects Require Custom Adhesive Formulations and Why?

Read Article

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Read Article

Characteristics of MMAs

Read Article

Testing the effectiveness of surface treatments

Read Article

Sponsored Articles

Unique Advantages of Contact Adhesives

Read Article

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Read Article

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Read Article

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Read Article
Information provided by Gluespec

Why Register?

  • View Technical Details
  • View Test Methods
  • View Key Specifications
  • View Similar Materials
  • Save your Project Searches

Already registered? Sign in.

Questions? Learn more about Gluespec

Gluespec Poll

When you're researching or sourcing materials online, what device are you using?
Shear Strength Test Methods
Shear Strength Type Substrate Test Method
2,500 psi Overlap Shear Strength cold rolled steel ASTM D1002 using cold rolled steel substrates with MEK wipe, Scotch-Brite™ abrade, MEK wipe bonding surface prep and 3-5 mil spacer beads.