• Description for 3M TE040

    One-component, moisture curing, urethane adhesive with low viscosity. Has a fast set time and is ideal for bonding most wood, plastics, metal and glass.

    *See Terms of Use Below

    Chemical Resistance Chemical Resistance: Highly plasticizer resistant
    Application Type Bond
    1 Part or 2 Part 1-Part
    Material Form Liquid
    Substrate Polyacrylic, FRP, Glass, Metal, Polycarbonate, PVC, Maple, Polystyrene, ABS, Plastic, Wood
    Manufacturer 3M
    Chemistry Polyurethane, Urethane
    Cure Method Moisture
    Application Temperature (°F) 250
    Viscosity (cPs) Low, 7,000
    Color White/Off-White, White/Off-White
    Density (g/cm³) 8.9 (lbs/gal)
  • Technical Data for 3M TE040

    Overview
    • Chemical Resistance
      • Chemical Resistance : Plasticizer Resistance - Highly plasticizer resistant
    • Application Type
    • 1 Part or 2 Part
      • 1-Part
    • Material Form
      • Liquid
    • Substrate
    • Chemistry
    • Cure Method
      • Moisture / Condensation Cure - Moisture
    • Color
      • Off-White - White/Off-White
      • White - White/Off-White
    Specifications
    Cure Specs
    Application Temperature (°F) 250
    Viscosity (cPs) Low, 7,000 Test Method
    Set Time (min) Fast, 0.67 Test Method
    Work / Pot Time (min) 2.00 Test Method
    Bond Strength
    General Bond Strength (psi) High
    Peel Strength (piw) 66, 60, 67, 22, 65, 90, 52, 54, 22, 35 Test Method
    Shear Strength (psi) 970, 2,310, 1,590, 1,110, 690, 1,290, 2,110, 260, 880, 230, 385, 810, 945 Test Method
    Tensile Strength (psi) 2,750 Test Method
    Hardness
    Shore D Hardness 35 Test Method
    Elongation (%) 860 Test Method
    Flexibility Flexible
    Modulus (psi) 2,850 Test Method
    Other Properties
    % Solids (%) 100
    Density (g/cm³) 8.9 (lbs/gal) Test Method
    Business Information
    Shelf Life Details For maximum shelf life, store product at normal indoor warehouse storage (below 120°F/49°C)., Products in 10 fluid ounce cartridge and 2 kilogram have 12 months while all others have a 6 month shelf life in unopened containers., For maximum shelf life, store product at normal indoor warehouse storage (below 120°F/49°C)., Products in 10 fluid ounce cartridge and 2 kilogram have 12 months while all others have a 6 month shelf life in unopened containers.
    Shelf Life Temperature (°F) <120, <120
    Shelf Life (mon) 12, 6
    Not Good For
    Don't Use With Substrates that exceed 275°F (135°C).
  • Best Practices for 3M TE040

    *See Terms of Use Below

    1. Surface Preparation

      See Vendor Technical Data Sheet for more info.

    2. Curing

      The cure rate will vary depending on air temperature, relative humidity, substrate type and bond line thickness. Cure rate is more rapid on wood (moisture-rich substrate) than on plastic.

    3. Clean-Up

      Allow product to solidify. Remove uncured waxy material (usually within the first 20 minutes after application) by scraping with a putty knife or similar tool. For cured material, remove by cutting or sanding. Do not use heat or flame to remove adhesive.

  • Comparable Materials for 3M TE040

    *See Terms of Use Below

    Spec Engine® Results

    Closest Results from this Manufacturer

Popular Articles

An Overview of Fluid Dispensing Systems & How They’re Used

Read Article

Characteristics of MMAs

Read Article

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Read Article

Testing the effectiveness of surface treatments

Read Article

Sponsored Articles

Unique Advantages of Contact Adhesives

Read Article

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Read Article

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Read Article

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Read Article

Featured Ads

Top Catalog Pages for 3M TE040

Gluespec Poll

When you're researching or sourcing materials online, what device are you using?
Set Time Test Methods
Set Time Test Method
Fast
0.67 min The minimum amount of time required between when the bond is made and when it will support a 5 psi tensile load., Open times and set times are based on a room temperature environment. High temperatures will lengthen open times and set times while lower environmental temperatures will shorten open times and set times.
Viscosity Test Methods
Viscosity Test Method Temperature
Low
7,000 cPs Brookfield viscometer with Thermosel using spindle #27. 121°C
Work / Pot Time Test Methods
Work / Pot Time Test Method
2.00 min The bonding range of a 1/8" bead of molten adhesive on a non-metallic substrate., Open times and set times are based on a room temperature environment. High temperatures will lengthen open times and set times while lower environmental temperatures will sho
Peel Strength Test Methods
Peel Strength Type Cure Time Cure Temperature Substrate Test Temperature Test Method
66 piw 180° Peel strength FRP 23°C Cotton duck failed during test, 180° peel strengths were measured on 1" x 8" pieces of flexible cotton duck (canvas) bonded to rigid 1" x 4" substrates. The rigid substrates were approximately .125" thick and the separation rate of the testing jaws was 2" per minute. All strengths were measured at 73°F (23°C).
60 piw 180° Peel strength Polycarbonate 23°C Cotton duck failed during test, 180° peel strengths were measured on 1" x 8" pieces of flexible cotton duck (canvas) bonded to rigid 1" x 4" substrates. The rigid substrates were approximately .125" thick and the separation rate of the testing jaws was 2" per minute. All strengths were measured at 73°F (23°C).
67 piw 180° Peel strength Polyacrylic 23°C 180° peel strengths were measured on 1" x 8" pieces of flexible cotton duck (canvas) bonded to rigid 1" x 4" substrates. The rigid substrates were approximately .125" thick and the separation rate of the testing jaws was 2" per minute. All strengths were measured at 73°F (23°C).
22 piw 180° Peel strength Polystyrene 23°C 180° peel strengths were measured on 1" x 8" pieces of flexible cotton duck (canvas) bonded to rigid 1" x 4" substrates. The rigid substrates were approximately .125" thick and the separation rate of the testing jaws was 2" per minute. All strengths were measured at 73°F (23°C).
65 piw 180° Peel strength ABS 23°C 180° peel strengths were measured on 1" x 8" pieces of flexible cotton duck (canvas) bonded to rigid 1" x 4" substrates. The rigid substrates were approximately .125" thick and the separation rate of the testing jaws was 2" per minute. All strengths were measured at 73°F (23°C).
90 piw 180° Peel strength PVC 23°C Cotton duck failed during test, 180° peel strengths were measured on 1" x 8" pieces of flexible cotton duck (canvas) bonded to rigid 1" x 4" substrates. The rigid substrates were approximately .125" thick and the separation rate of the testing jaws was 2" per minute. All strengths were measured at 73°F (23°C).
52 piw 180° Peel strength Aluminum 23°C 180° peel strengths were measured on 1" x 8" pieces of flexible cotton duck (canvas) bonded to rigid 1" x 4" substrates. The rigid substrates were approximately .125" thick and the separation rate of the testing jaws was 2" per minute. All strengths were measured at 73°F (23°C).
54 piw 180° Peel strength Glass 23°C 180° peel strengths were measured on 1" x 8" pieces of flexible cotton duck (canvas) bonded to rigid 1" x 4" substrates. The rigid substrates were approximately .125" thick and the separation rate of the testing jaws was 2" per minute. All strengths were measured at 73°F (23°C).
22 piw T-peel strength Plasticized Vinyl 23°C Substrate failure, T-Peel strengths were measure on 1" wide pieces of plasticized vinyl at 73°F (23°C). The separation rate of the testing jaws was 2" per minute. Plasticized Vinyl, T-Peel (piw), tested @ 73°F (23°C)
35 piw T-peel strength 20,160 min 71°C Plasticized Vinyl 23°C Substrate failure, T-Peel strengths were measure on 1" wide pieces of plasticized vinyl at 73°F (23°C). The separation rate of the testing jaws was 2" per minute. Plasticized Vinyl, T-Peel (piw), tested @ 73°F (23°C)
Tensile Strength Test Methods
Tensile Strength Cure Time Cure Temperature Cure Humidity Test Method
2,750 psi 10,080 min 25°C 50 % ASTM D 638, Die C, measured on .011" - .017" thick films cured 7 days at 77°F (25°C)/50% relative humidity (RH), @ Break
Shear Strength Test Methods
Shear Strength Type Cure Time Cure Temperature Cure Humidity Substrate Test Time Test Temperature Test Method
970 psi Overlap shear strength Maple 23°C Overlap shear (OLS) strengths were measured on 1" wide 1/2" overlap specimens. These bonds were made individually using 1" x 4" sample coupons. The thickness of the bond line was .003-.006". The thickness of the substrates were: plastics, .125", Maple, .375".The separation rate of the testing jaws was 2" per minute.
2,310 psi Overlap shear strength FRP 23°C Overlap shear (OLS) strengths were measured on 1" wide 1/2" overlap specimens. These bonds were made individually using 1" x 4" sample coupons. The thickness of the bond line was .003-.006". The thickness of the substrates were: plastics, .125", Maple, .375". The separation rate of the testing jaws was 2" per minute.
1,590 psi Overlap shear strength Polycarbonate 23°C Overlap shear (OLS) strengths were measured on 1" wide 1/2" overlap specimens. These bonds were made individually using 1" x 4" sample coupons. The thickness of the bond line was .003-.006". The thickness of the substrates were: plastics, .125", Maple, .375". The separation rate of the testing jaws was 2" per minute.
1,110 psi Overlap shear strength Polyacrylic 23°C Overlap shear (OLS) strengths were measured on 1" wide 1/2" overlap specimens. These bonds were made individually using 1" x 4" sample coupons. The thickness of the bond line was .003-.006". The thickness of the substrates were: plastics, .125", Maple, .375". The separation rate of the testing jaws was 2" per minute.
690 psi Overlap shear strength Polystyrene 23°C Overlap shear (OLS) strengths were measured on 1" wide 1/2" overlap specimens. These bonds were made individually using 1" x 4" sample coupons. The thickness of the bond line was .003-.006". The thickness of the substrates were: plastics, .125", Maple, .375". The separation rate of the testing jaws was 2" per minute.
1,290 psi Overlap shear strength ABS 23°C Substrate failure, Overlap shear (OLS) strengths were measured on 1" wide 1/2" overlap specimens. These bonds were made individually using 1" x 4" sample coupons. The thickness of the bond line was .003-.006". The thickness of the substrates were: plastics, .125", Maple, .375". The separation rate of the testing jaws was 2" per minute.
2,110 psi Overlap shear strength PVC 23°C Substrate Failure, Overlap shear (OLS) strengths were measured on 1" wide 1/2" overlap specimens. These bonds were made individually using 1" x 4" sample coupons. The thickness of the bond line was .003-.006". The thickness of the substrates were: plastics, .125", Maple, .375". The separation rate of the testing jaws was 2" per minute.
260 psi Overlap shear strength Maple 82°C Overlap shear (OLS) strengths were measured on 1" wide 1/2" overlap specimens. These bonds were made individually using 1" x 4" sample coupons. The thickness of the bond line was .003-.006". The thickness of the substrates were: plastics, .125", Maple, .375". The separation rate of the testing jaws was 2" per minute.
880 psi Overlap shear strength FRP 82°C Overlap shear (OLS) strengths were measured on 1" wide 1/2" overlap specimens.These bonds were made individually using 1" x 4" sample coupons. The thickness of the bond line was .003-.006". The thickness of the substrates were: plastics, .125", Maple, .375". The separation rate of the testing jaws was 2" per minute.
230 psi Overlap shear strength 10,080 min 25°C FRP 600 sec 23°C FRP, Overlap Shear Strength (psi), tested @ 73°F (23°C) at various times after bonding. The FRP was conditioned for 7 days at 77°F (25°C)/50% RH prior to bonding.
385 psi Overlap shear strength 10,080 min 25°C FRP 3,600 sec 23°C FRP, Overlap Shear Strength (psi), tested @ 73°F (23°C) at various times after bonding. The FRP was conditioned for 7 days at 77°F (25°C)/50% RH prior to bonding.
810 psi Overlap shear strength 10,080 min 25°C FRP 86,400 sec 23°C FRP, Overlap Shear Strength (psi), tested @ 73°F (23°C) at various times after bonding. The FRP was conditioned for 7 days at 77°F (25°C)/50% RH prior to bonding.
945 psi Overlap shear strength 10,080 min 25°C FRP 604,800 sec 23°C FRP, Overlap Shear Strength (psi), tested @ 73°F (23°C) at various times after bonding. The FRP was conditioned for 7 days at 77°F (25°C)/50% RH prior to bonding.
Elongation Test Methods
Elongation Test Method
860 % ASTM D 638, Die C, measured on .011" - .017" thick films cured 7 days at 77°F (25°C)/50% relative humidity (RH), at Break
Modulus Test Methods
Modulus Test Method
2,850 psi ASTM D 638, Die C, measured on .011" - .017" thick films cured 7 days at 77°F (25°C)/50% relative humidity (RH)
Shore D Hardness Test Methods
Shore D Hardness Shore Hardness Test Method
35 1Measured on .090" - .110" thick bars
Density Test Methods
Density Test Method
8.9 (lbs/gal) Molten