• Description for Bostik 2402

    Light brown, Marine adhesive. Tough resilient bond. Good adhesion to Hypalon inflatables. Resistant to heat, moisture, acids, alkalis, gasoline, oil and kerosene.

    *See Terms of Use Below

    Application Type Bond, Gasket
    1 Part or 2 Part 2 Part
    Material Form Liquid
    Substrate Rubber
    Industry Marine, Belt splicing, Flooring installation, Hypalon rubber boat repair, News print splicing
    Manufacturer Bostik
    Chemistry Synthetic rubber, Natural rubber based, Solvent-based, Water borne, Polychloroprene Rubber
    Cure Method 2 parts, Heat
    Cure Temperature (°C) >70
    Cure Time (min) <10,080, 120
    Viscosity (cPs) 3,300 to 4,200, 2,500 to 3,200
    Color Light brown
    Chemical Resistance Good, Acids, Gasoline, oil, kerosene
    High Temperature Resistance (°C) high heat resistance
    Durability Tough
    Density (g/cm³) 8 (WT./GAL.), 0.890
  • Technical Data for Bostik 2402

    • Application Type
    • 1 Part or 2 Part
      • 1 Part or 2 Part - 2 Part
    • Material Form
      • Liquid
    • Substrate
    • Industry
      • Marine - Hypalon rubber boat repair
      • Splicing - Belt splicing, News print splicing
      • Flooring - Flooring installation
      • Other - Cabinet lamination, Carpet bonding, Vacuum forming vinyls, Films
    • Chemistry
    • Application Method
      • Roll - Roller
      • Brush
    • Cure Method
      • Heat
      • 2-Part Cure - 2 parts
    • Color
      • Brown - Light brown
    Cure Specs
    Cure Temperature (°C) >70
    Cure Time (min) <10,080, 120
    Viscosity (cPs) 3,300 to 4,200, 2,500 to 3,200 Test Method
    Work / Pot Time (min) 360 to 480, 0.10 Test Method
    Mix Ratio 12:5:1 (by volume)
    Material Resistance
    Chemical Resistance Good, Acids, Gasoline, oil, kerosene
    High Temperature Resistance (°C) high heat resistance
    Moisture/Humidity Resistance Moisture resistance
    Durability Tough
    Flexibility Resilient
    Other Properties
    % Solids (%) 25 to 28 Test Method
    Density (g/cm³) 8 (WT./GAL.), 0.890
    Business Information
    Shelf Life Details Store away from heat sources and under cover. The solvent vapours are highly flammable. A minimum shelf life of 12 months from date of manufacture if stored under cover below 30°C.
    Shelf Life Temperature (°F) <86
    Shelf Life Type From date of manufacture
    Shelf Life (mon) 12
  • Best Practices for Bostik 2402

    *See Terms of Use Below

    1. Surface Preparation

      Surfaces must be clean and grease free. They may be cleaned by abrading the surface with clean emery cloth or by using Bostik 9913 Solvent to remove surface contamination. Solvent cleaning should not be adopted for those surfaces where the bond strength is likely to be affected adversely by the penetration of the solvent into the materials. For maximum adhesion, abrading is preferable to solvent cleaning. Some rubbers (particularly natural) require priming with Bostik 9300 Primer prior to application of Bostik 2402 adhesive. Test strips should be made up and tested to ensure the best bond possible will be obtained. For the strongest adhesion to metal, and some plastics Bostik 9252 Primer must be used. Stir the primers thoroughly prior to the application of a medium brush coat to the prepared metal surfaces. Allow the primer coat to dry for at least one hour before applying adhesive.

    2. Application

      In some cases a single adhesive application to each surface may not be sufficient (e.g. porous surfaces) then multicoat applications may be needed to build up film thickness. In this case, each coat should be allowed to dry for about 40-45 minutes except the final one which should have 10 - 20 minutes. It is always advisable to build up film thickness with a number of thin coats rather than a single heavy coat.

      Allow the 2 films to dry for 10-20 minutes, or until they can be touched with the knuckles without any cement being transferred.

    3. Mixing

      Add approximately 4% w/w Bostik 9101 Curing Agent to 2402 Adhesive and stir in thoroughly for at least 2 minutes.

    4. Clean-Up

      Clean up and thin with Bostik 9913 solvent only.

  • Comparable Materials for Bostik 2402

    *See Terms of Use Below

    Spec Engine® Results

    Closest Results from this Manufacturer

Questions about this material?

Get personal assistance with your specific application needs.

Your Profile Edit
  1. 726be975-c18e-41d3-bd2f-e2cc163c5963
  2. 726be975-c18e-41d3-bd2f-e2cc163c5963

Popular Articles

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Read Article

Water-based Adhesives in Furniture

Read Article

Testing the effectiveness of surface treatments

Read Article

Water Based Adhesives in the Textile Industry

Read Article

Sponsored Articles

Unique Advantages of Contact Adhesives

Read Article

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Read Article

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Read Article

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Read Article
Information provided by Gluespec

Why Register?

  • View Technical Details
  • View Test Methods
  • View Key Specifications
  • View Similar Materials
  • Save your Project Searches

Already registered? Sign in.

Questions? Learn more about Gluespec

Gluespec Poll

When you're researching or sourcing materials online, what device are you using?
Viscosity Test Methods
Viscosity Test Method Temperature
3,300 to 4,200 cPs
2,500 to 3,200 cPs BTM V001 25°C
Work / Pot Time Test Methods
Work / Pot Time Temperature
360 to 480 min 25°C
0.10 min
% Solids Test Methods
% Solids Test Method
25 to 28 % BTM N001, w/w