Bostik FRP Panel Adhesive Datasheet Bostik FRP Panel Adhesive

Information provided by Gluespec
  • Description for Bostik FRP Panel Adhesive

    Synthetic acrylic, latex based adhesive; low odor; production controlled viscosity; water resistant; easy application; fast grab.

    *See Terms of Use Below

    Chemical Resistance Chemical Resistance: Fluid Resistance: Excellent water resistance
    Application Type Bond
    1 Part or 2 Part 1-Part
    Material Form Liquid
    Manufacturer Bostik
    Chemistry Resin, Synthetic rubber, Solvent-based
    Application Method Trowel
    Cure Method Solvent
    Application Temperature (°F) 41 to 100
    Cure Time (min) 14,400 to 20,160
    Viscosity (cPs) 320,000
    Ozone Resistance Excellent ozone resistance
    High Temperature Resistance (°C) 49
    Low Temperature Resistance (°C) -18
    Density (g/cm³) 5.4 (kg)
    Key Specifications ASTM (American Standard Test Method): ASTM C-557
  • Technical Data for Bostik FRP Panel Adhesive

    Overview
    • Chemical Resistance
      • Chemical Resistance : Fluid Resistance : Water Resistance - Excellent water resistance
    • Application Type
    • 1 Part or 2 Part
      • 1-Part
    • Material Form
      • Liquid
    • Chemistry
    • Application Method
      • Spatula/Trowel - Trowel
    • Cure Method
      • Solvent
    • Key Specifications
      • ASTM (American Standard Test Method) : C-557 - ASTM C-557
    Specifications
    Cure Specs
    Application Temperature (°F) 41 to 100
    Cure Time (min) 14,400 to 20,160
    Viscosity (cPs) 320,000
    Work / Pot Time (min) 30
    Bond Strength
    Shear Strength (psi) 50, 233, 265, 100, 125, 175, 270 Test Method
    Material Resistance
    Ozone Resistance Excellent ozone resistance
    High Temperature Resistance (°C) 49
    Low Temperature Resistance (°C) -18
    Hardness
    Flexibility Very good
    Other Properties
    Flash Point (°F) -23.8
    Density (g/cm³) 5.4 (kg)
    Business Information
    Shelf Life Type From date of purchase
    Shelf Life (mon) 12
    Not Good For
    Don't Use With foamboard (Polystyrene), wallpaper, NRP Panels (nonreinforced plastic), Bad Substrates
  • Best Practices for Bostik FRP Panel Adhesive

    *See Terms of Use Below

    1. Surface Preparation

      For best results, adhesive and substrates should be between 50°- 90° F. Surfaces must be structurally sound and dry, free of grease, dirt, dust, wall paper, paint or anything that would interfere with a bond. Level any high spots and fill all cracks and holes with appropriate fillers.

    2. Application

      Cut and pre-fit FRP panels.

      Spread adhesive with the recommended trowel over entire back of the FRP panel.

      As soon as adhesive is spread over entire panel and before adhesive skins over (within 45 minutes), set panel in position and press against wall.

      Press panel firmly into place, working from the center to the edges until full contact has been made.

      Bracing may be required if walls or panels are not completely straight.

      For channel moldings, permanent fasteners, and panel spacings, follow FRP panel manufacturer’s specifications.

      For application over concrete: Concrete surfaces must be dry and completely cured. When installing FRP panels over below-grade concrete, where moisture can penetrate, you must first attach furring strips to the concrete block and then attach a solid surface, such as wood or drywall, to those furring strips. Then continue with standard FRP application.

    3. Curing

      Full cure 10-14 days on most substrates

    4. Clean-Up

      Use LIQUID NAILS™ Adhesive & Caulk Remover for best results. Mineral spirits can be substituted. Note warnings on mineral spirits container.

  • Comparable Materials for Bostik FRP Panel Adhesive

    *See Terms of Use Below

    Spec Engine® Results

    Closest Results from this Manufacturer

Popular Articles

Conformal Coatings Guide

Read Article

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Read Article

Testing the effectiveness of surface treatments

Read Article

Electrically Conductive Adhesives Guide

Read Article

Sponsored Articles

Unique Advantages of Contact Adhesives

Read Article

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Read Article

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Read Article

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Read Article

Featured Ads

Top Catalog Pages for Bostik FRP Panel Adhesive

Gluespec Poll

When you're researching or sourcing materials online, what device are you using?
Shear Strength Test Methods
Shear Strength Substrate Test Time
50 psi Wood to wood 86,400 sec
233 psi Wood to wood 172,800 sec
265 psi Wood to wood 604,800 sec
100 psi Wood to FRP 86,400 sec
125 psi Wood to FRP 172,800 sec
175 psi Wood to FRP 604,800 sec
270 psi Wood to FRP 1,209,600 sec