Bostik Thermogrip 6363

Bostik Thermogrip 6363 Datasheet
BUY ONLINE

  • Description for Bostik Thermogrip 6363

    General purpose hot melt adhesive: medium open time, exhibits good bonding characteristics

    *See Terms of Use Below

    Application Type Bond, Repair
    1 Part or 2 Part 1 Part
    Material Form Pellet, Stick
    Substrate Ceramics, Fabrics, Metal, Paper, Plastics, PlyWood, Porous, Wood
    Industry Automotive, Food
    Manufacturer Bostik
    Chemistry Hot melt
    Cure Method Hot melt
    Cure Time (min) 1,440
    Viscosity (cPs) 8,875, 14,250, 20,250, 33,500
    Color Off White
    Chemical Resistance Acids & Alkalies, Chemical resistance, Water
    High Temperature Resistance (°C) 52
    Low Temperature Resistance (°C) -29
    Density (g/cm³) 0.96 (g/cc)
    Key Specifications FDA (U.S. Food & Drug Administration) and/or CFIA (Canadian Food Inspection Agency): FDA 21 CFR 175.105

  • Technical Data for Bostik Thermogrip 6363

    *See Terms of Use Below

    Overview
    • Application Type
    • 1 Part or 2 Part
      • 1 Part or 2 Part - 1 Part
    • Material Form
      • Stick
      • Pellets - Pellet
    • Substrate
    • Industry
    • Chemistry
    • Cure Method
      • Hotmelt - Hot melt
    • Color
      • Off-White - Off White
    • Key Specifications
      • FDA (U.S. Food & Drug Administration) and/or CFIA (Canadian Food Inspection Agency): 175.105 - FDA 21 CFR 175.105
    Specifications
    Cure Specs
    Cure Time (min) 1,440
    Viscosity (cPs) 8,875, 14,250, 20,250, 33,500 Test Method
    Fixture or Handling Strength Time (min) 1,440
    Softening Point (°C) 75 to 92
    Open Time (min) Medium, 0.67
    Bond Strength
    Shear Strength (psi) 565 Test Method
    Material Resistance
    Chemical Resistance Acids & Alkalies, Chemical resistance, Water
    High Temperature Resistance (°C) 52
    Low Temperature Resistance (°C) -29
    Other Properties
    Specific Gravity 0.98 (gm/cc) Test Method
    Density (g/cm³) 0.96 (g/cc) Test Method
    Business Information
    Shelf Life Details Can be stored 730 days in a clean dry place in its original package at an average temperature of 25°C or below. Storage temperature should not exceed 40°C.
    Shelf Life Temperature (°F) 77
    Shelf Life (mon) 24

  • Best Practices for Bostik Thermogrip 6363

    *See Terms of Use Below

    1. Surface Preparation

      All surfaces should be clean and free of contaminants. If necessary, clean surfaces with solvent.

    2. Application

      Apply the adhesive to the more difficult-to-bond surface. In general, hard, smooth surfaces are more difficult to bond than rough, porous surfaces. Metals should be pre-warmed up to 200°F (95°C) for optimum results. Open-time varies depending on application temperature, amount of adhesive applied, type of substrate and ambient temperature conditions. Mate the surfaces to be bonded as quickly as possible after adhesive has been applied for optimum bond strength. Use firmest pressure practical for object being bonded. Do not move or adjust surfaces after contact has been made, as inferior bond strength will result. Typically, a properly formed hot melt adhesive bond will achieve 50% of its strength after 1 minute, 75% after 1 hour, and 100% after 1 day.

    3. Clean-Up

      Clean-up Procedure: Mineral oil or paraffin wax, not to exceed flash point as stated on the MSDS, followed by a thorough purge with the adhesive itself.

  • Comparable Materials for Bostik Thermogrip 6363

    *See Terms of Use Below

    Spec Engine® Results

    • 3M
      3738(3M)

      High delivery rate and long bonding range • General purpose for foundry sand cores, wood bonding, corrugated, selected plastics and chipboard

    • 3M
      3764(3M)

      Bonds variety of plastics including polycarbonate, polyethylene, and polypropylene • Flexible at low temperatures

    • Henkel
      Technomelt 0430(Henkel)

      Suitable for bonding expanded polystyrene, polyethylene, and urethane foams. Can be used in applications where solvent-based aerosols are used. Available in natural and red.

    • Compare All

    Closest Results from this Manufacturer

    • Bostik
      Thermogrip 2124(Bostik)

      Flexible hot melt adhesive, long set time, designed for high performance bonding of difficult substrates or substrate combinations.

    • Bostik
      Thermogrip 2109(Bostik)

      Medium-setting hot melt adhesive, economical with low viscosity and quick grab ability very good "gunability" in stick form.

    • Bostik
      Thermogrip 6327(Bostik)

      Medium open time hot melt; good shear strength and good adhesion to most plastics and porous substrates.

    • Compare All
  Download Technical Data Sheet   Save This Material Saved Items

Questions about this material?

Get personal assistance with your specific application needs.

Your Profile Edit
  1. a6b01794-adc2-480c-9d7c-836266d1d72e
  2. a6b01794-adc2-480c-9d7c-836266d1d72e
Submit

Popular Articles

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Read Article

What to know about Hot Melt Adhesives

Read Article

Hot Melt Adhesives in the Textile Industry

Read Article

Testing the effectiveness of surface treatments

Read Article

Sponsored Articles

Unique Advantages of Contact Adhesives

Read Article

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Read Article

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Read Article

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Read Article
Information provided by Gluespec

Why Register?

  • View Technical Details
  • View Test Methods
  • View Key Specifications
  • View Similar Materials
  • Save your Project Searches

Already registered? Sign in.

Questions? Learn more about Gluespec

Gluespec Poll

Who do you read or follow for engineering news and entertainment?
Viscosity Test Methods
Viscosity Test Method Temperature
8,875 cPs Approximately, Thermosel Viscocity Brookfield-ASTM D3236 204°C
14,250 cPs Approximately, Thermosel Viscocity Brookfield-ASTM D3236 191°C
20,250 cPs Approximately, Thermosel Viscocity Brookfield-ASTM D3236 177°C
33,500 cPs Approximately, Thermosel Viscocity Brookfield-ASTM D3236 163°C
Shear Strength Test Methods
Shear Strength Substrate
565 psi Plywood
Density Test Methods
Density Temperature
0.96 (g/cc) 25°C
Specific Gravity Test Methods
Specific Gravity Test Method
0.98 (gm/cc) After 24 Hour Cure