Dow 3145 RTV Grey Adhesive/Sealant Datasheet Dow 3145 RTV Grey Adhesive/Sealant

Information provided by Gluespec
  • Description for Dow 3145 RTV Grey Adhesive/Sealant

    Noncorrosive; high tensile strength, elongation, peel and lap shear values, good for high temperature applications; non-flow.

    *See Terms of Use Below

    Application Type Bond, Seal, Gaskets
    1 Part or 2 Part 1-Part
    Material Form Pre-Cure: Paste, Post-Cure: Elastomer
    Substrate Ceramics, Glass, Reactive metals, Selected Plastics
    Industry Circuit boards, Light Emitting Diodes (LEDs), Smart Meters, E-Mobility Solutions, Smart Home Devices, Power Tools, CRT module, Electrical leads, Electronic equipment, Electronics, LCD module, Modules, PDP module, Power supplies, PWBs
    Manufacturer Dow
    Chemistry Silicone elastomer
    Cure Method RTV, Moisture
    Cure Temperature (°C) Faster or lower, 20 to 25, 20 to 25
    Viscosity (cPs) Non-flow
    Color Gray
    High Temperature Resistance (°C) 200
    Low Temperature Resistance (°C) -45, -55
    Volume Resistivity (O) 4.4E+14 (ohm-cm)
    Key Specifications Mil-Spec (United States Military Standard): MIL-A-46146; MIL-A-46146 Group II/III, TY I, Mil-Spec (United States Military Standard): A-46146: MIL-A-46146; MIL-A-46146 Group II/III, TY I
  • Technical Data for Dow 3145 RTV Grey Adhesive/Sealant

    Overview
    • Application Type
    • 1 Part or 2 Part
      • 1-Part
    • Material Form
      • Elastomer - Post-Cure: Elastomer
      • Paste - Pre-Cure: Paste
    • Substrate
    • Industry
      • LED (Light-Emitting Diodes) - Light Emitting Diodes (LEDs)
      • Smart Meters
      • Smart Home Devices
      • E-Mobility Solutions
      • Electronics - Circuit boards, CRT module, Electrical leads, Electronic equipment, LCD module, Modules, PDP module, Power supplies, PWBs
      • Power Supplies
      • Industrial - Housings, Yoke
      • Power Tools
    • Chemistry
    • Application Method
      • Dispenser - Automated or manual needle dispense system
    • Cure Method
      • Moisture / Condensation Cure - Moisture
      • RTV (Room Temperature Vulcanization) - RTV
    • Color
      • Gray
    • Key Specifications
      • Mil-Spec (United States Military Standard) : A-46146 - MIL-A-46146; MIL-A-46146 Group II/III, TY I
      • Mil-Spec (United States Military Standard) : A-46146 : Group II and III, TY I - MIL-A-46146; MIL-A-46146 Group II/III, TY I
    Specifications
    Cure Specs
    Cure Temperature (°C) Faster or lower, 20 to 25, 20 to 25
    Cure Time (min)
    Viscosity (cPs) Non-flow
    Tack Free Time (min) Fast Test Method
    Bond Strength
    Peel Strength (piw) High, 106 (ppi) Test Method
    Shear Strength (psi) High Test Method
    Tear Strength (piw) 190 (ppi) Test Method
    Tensile Strength (psi) High, 1,035
    Material Resistance
    Environmental Resistance Environmental resistance
    High Temperature Resistance (°C) 200
    Low Temperature Resistance (°C) -45, -55
    Moisture/Humidity Resistance Moisture/humidity resistance
    Conductivity
    Dissipation Factor 0.00050, <0.00020 Test Method
    Dielectric Strength (V/mil) Good, Durable
    Dielectric Constant 2.83, 2.83 Test Method
    Volume Resistivity (O) 4.4E+14 (ohm-cm)
    Hardness
    Shore A Hardness 51
    Elongation (%) High, 670
    Flexibility Flexible
    Modulus (psi) 150 Test Method
    Other Properties
    Specific Gravity 1.120
    Coefficient of Thermal Expansion (CTE) 375 (Linear micron/m °C or ppm)
    Business Information
    Shelf Life Details Shelf life is indicated by the “Use Before” date found on the product label. For best results, Dow Corning RTV adhesives should be stored at or below the storage temperature listed on the product label. Special precautions must be taken to prevent moisture from contacting these materials. Containers should be kept tightly closed with head or air space minimized. Partially filled containers should be purged with dry air or other gases, such as nitrogen.
    Shelf Life Temperature (°F) 77
    Shelf Life Type From date of manufacture
    Shelf Life (mon) 12
    Not Good For
    Don't Use With Non-reactive plastic surfaces, Rubber substrates that are highly plasticized, Teflon, Polyethylene, Polypropylene, Plastic substrates that are highly plasticized
  • Best Practices for Dow 3145 RTV Grey Adhesive/Sealant

    *See Terms of Use Below

    1. Surface Preparation

      All surfaces should be thoroughly cleaned and/or degreased with Dow Corning® brand OS Fluids, naphtha, mineral spirits, methyl ethyl ketone (MEK) or other suitable solvent. Solvents such as acetone or isopropyl alcohol (IPA) do not tend to remove oils well, and any oils remaining on the surface may interfere with adhesion. Light surface abrasion is recommended whenever possible, because it promotes good cleaning and increases the surface area for bonding. A final surface wipe with acetone or IPA is also useful. Some cleaning techniques may provide better results than others

      users should determine the best techniques for their particular applications.

    2. Mixing

      Upon standing, some filler may settle to the bottom of the liquid containers after several weeks. To ensure a uniform product mix, the material in each container should be thoroughly mixed prior to use. Two-part materials should be mixed in the proper ratio (1:1 or 10:1) either by weight or volume. The presence of light colored streaks or marbling indicates inadequate mixing.

    3. Deairing/Degassing

      Automated airless dispense equipment can be used to reduce or avoid the need to de-air. If de-airing is required to reduce voids in the cured elastomer, consider a vacuum de-air schedule of >28 inches Hg for 10 minutes or until bubbling subsides.

  • Comparable Materials for Dow 3145 RTV Grey Adhesive/Sealant

    *See Terms of Use Below

    Spec Engine® Results

Popular Articles

What Are the Differences Between Adhesives and Sealants?

Read Article

Testing the effectiveness of surface treatments

Read Article

Silicones in LED Lighting | Gluespec

Read Article

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Read Article

Sponsored Articles

Unique Advantages of Contact Adhesives

Read Article

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Read Article

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Read Article

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Read Article

Featured Ads

Gluespec Poll

When you're researching or sourcing materials online, what device are you using?
Tack Free Time Test Methods
Tack Free Time Tack Free Temperature
Fast
Peel Strength Test Methods
Peel Strength Type
High
106 (ppi) 180 Degree Peel Strength
Tear Strength Test Methods
Tear Strength Test Method
190 (ppi) Die B
Shear Strength Test Methods
Shear Strength Type
High Lap shear strength
Dielectric Constant Test Methods
Dielectric Constant Test Method
2.83 Dielectric Constant, 100 Hz
2.83 Dielectric Constant, 100 KHz
Dissipation Factor Test Methods
Dissipation Factor Test Method
0.00050 Dissipation Factor, 100 Hz
<0.00020 Dissipation Factor, 100 KHz
Modulus Test Methods
Modulus Test Method
150 psi Tensile Modulus