Henkel 531 Datasheet Henkel 531

CONTACT REP
Information provided by Gluespec

  • Description for Henkel 531

    • Structural Acrylic Adhesive • Magnet Bonding Structural • Metal & Glass Bonding • Rapid Room Temperature Cure • Fixtures Parts in 15 to 30 Seconds • 50% Strength Obtained in 15 Minutes • Environmentally Friendly – 100% Solids • Nonflammable • No Mix Application • Excellent Adhesion to Ferrite Magnet and Metal Surfaces<br/>

    *See Terms of Use Below

    Brand Bondmaster
    Chemical Resistance Salt Spray
    Application Type Bond
    1 Part or 2 Part 2-Part
    Material Form Liquid
    Substrate Glass, Alnico, Plastics, Zinc plated Steel, Stainless Steel, Zinc Dichromate, Galvanized Steel, Galvanized Steel, Epoxy-Coated Metal, Rigid Plastics, Steel, Zinc Plated, Ferrite, Zinc plated Steel, Metals, Painted Metal
    Industry Electrical, Automotive, Magnets, Sensors, FlyWheels, DC motors, Motors, Generators
    Manufacturer Henkel
    Chemistry Acrylic
    Cure Method Room Temperature Cure
    Cure Temperature (°C) 20 to 25 Room Temperature, 25
    Cure Time (min) Rapid, 60
    Viscosity (cPs) 3,000
    Color Amber
    High Temperature Resistance (°C) 163
    Low Temperature Resistance (°C) -65

  • Technical Data for Henkel 531

    *See Terms of Use Below

    Overview
    • Chemical Resistance
      • Chemical Resistance - Salt Spray
    • Application Type
    • 1 Part or 2 Part
      • 2-Part
    • Material Form
      • Liquid
    • Substrate
      • Glass
      • Metal - Alnico, Epoxy-Coated Metal, Ferrite, Metals, Painted Metal
      • Steel - Zinc plated Steel
      • Zinc - Zinc Dichromate, Zinc Plated, Zinc plated Steel
      • Galvanized - Galvanized Steel
      • Plastic - Plastics, Rigid Plastics
      • Stainless Steel
      • Galvanized Steel
      • Other - Rare earth
    • Industry
    • Chemistry
    • Application Method
      • Brush - Wipe
      • Spray
    • Cure Method
      • Room Temperature / Air Dry - Room Temperature Cure
    • Color
      • Red - Amber
    • Brand
      • Bondmaster
    Specifications
    Cure Specs
    Cure Temperature (°C) 20 to 25 Room Temperature, 25
    Cure Time (min) Rapid, 60
    Viscosity (cPs) 3,000 Test Method
    Fixture or Handling Strength Time (min) 0.25 to 0.50 Test Method
    Work / Pot Time (min) 30 Test Method
    Mix Ratio 30:1 (by volume)
    Bond Strength
    Structural/Load-Bearing Structural
    General Bond Strength (psi) Excellent
    Peel Strength (piw) 20 to 25 Test Method
    Shear Strength (psi) High, 3,500, 3,000, 2,000, 3,500, 3,000, 2,000, 2,000, 2,000, 2,000, 250 Test Method
    Impact Strength (psi) High, 15 Test Method
    Material Resistance
    High Temperature Resistance (°C) 163
    Impact Resistance Impact resistance
    Low Temperature Resistance (°C) -65
    Hardness
    Shore D Hardness 60 to 65 Test Method
    Other Properties
    Specific Gravity 1.100
    Flash Point (°F) >199.4
    % Solids (%) 100
    Business Information
    Shelf Life Details A shelf life of one year when stored in a refrigerator.
    Shelf Life (mon) 12
    Not Good For
    Don't Use With Delrin, Polyethylene, Polyproplene, Polyurethane, Any type of elastomer, Acetal

  • Best Practices for Henkel 531

    *See Terms of Use Below

    1. Surface Preparation

      The 531 adhesive requires no surface preparation on most metal, ferrite, and glass surfaces. For optimum bond strength on metal parts, the surface should be washed with a solvent or cleansing solution, abraded with an abrasive pad, and then rinsed with a solvent or cleansing solution. Glass surfaces should be cleaned with a commercial glass cleaner before bonding. Painted surfaces should be abraded lightly and then wiped clean.

    2. Application

      Apply BONDMASTER 534 Activator by spraying, wiping, or brushing a thin film of the activator on one of the bonding surfaces.

      Apply BONDMASTER 531 Adhesive to the bond area on the non-activated bonding surface.

      Join surfaces with sufficient pressure to maintain intimate contact between the parts until handling strength is obtained.

      A 15 - 30 second clamp time is usually required for bonding of parts with minimal gap.

    3. Clean-Up

      Unreacted Part A & Part B can be cleaned up using acetone, isopropanol, or MEK.

  • Comparable Materials for Henkel 531

    *See Terms of Use Below

    Spec Engine® Results

    • Henkel
      Loctite 3875(Henkel)

      Two-component, Bead-on-bead, thermally conductive adhesive is designed to thermally couple and structurally bond heats sinks to heat dissipating electronic components.

    • Henkel
      533(Henkel)

      • Structural Acrylic Adhesive • Rapid Room Temperature Cure • Fixtures Parts in 15 to 30 Seconds • 50% Strength Obtained in 15 Minutes • Excellent Adhesion to Magnet and Metal Surfaces • Nonflammable • Environmentally Friendly - 100% Solids • No Mix Application • Non-Drip Rheology •

    • Compare All
  Download Technical Data Sheet   Save This Material   Compare View Saved Items

Popular Articles

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Read Article

Testing the effectiveness of surface treatments

Read Article

Plastic Bonding with Adhesives - Considerations Q&A

Read Article

What Projects Require Custom Adhesive Formulations and Why?

Read Article

Sponsored Articles

Unique Advantages of Contact Adhesives

Read Article

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Read Article

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Read Article

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Read Article

Featured Ads

Top Catalog Pages for Henkel 531

All Henkel Materials
View Now
Sensors
View Now
Plastic Bonding
View Now

Gluespec Poll

When you're researching or sourcing materials online, what device are you using?
Fixture or Handling Strength Time Test Methods
Fixture or Handling Strength Time Fixture-Handling Strength Time Temperature
0.25 to 0.50 min 25°C
Viscosity Test Methods
Viscosity Test Method Temperature
3,000 cPs Viscosity, Brookfield, 25oC @ 20 rpm 25°C
Work / Pot Time Test Methods
Work / Pot Time Temperature
30 min 25°C
Impact Strength Test Methods
Impact Strength Substrate Test Method
High
15 psi Steel ASTM 950
Peel Strength Test Methods
Peel Strength Substrate Test Method
20 to 25 piw Steel/Steel ASTM 1876
Shear Strength Test Methods
Shear Strength Type Substrate Test Temperature Test Method
High
3,500 psi Lap shear strength Steel/Steel 25°C ASTM D1002
3,000 psi Lap shear strength Aluminum/Aluminum 25°C ASTM D1002
2,000 psi Lap shear strength Galvanized steel/Galvanized steel 25°C ASTM D1002
3,500 psi Lap shear strength Stainless steel/Stainless steel 25°C ASTM D1002
3,000 psi Lap shear strength Zinc plated Steel/Zinc plated steel 25°C ASTM D1002
2,000 psi Lap shear strength Ferrite /Steel 25°C ASTM D1002, Substrate failure
2,000 psi Lap shear strength Ferrite/Zinc Dichromate 25°C ASTM D1002, Substrate failure
2,000 psi Lap shear strength Ferrite/Galvanized Steel 25°C ASTM D1002, Substrate failure
2,000 psi Lap shear strength Ferrite/Zinc plated 25°C ASTM D1002, Substrate failure
250 psi Lap shear strength Glass/Glass 25°C ASTM D1002, Substrate failure
Shore D Hardness Test Methods
Shore D Hardness Hardness Temperature
60 to 65 25°C