Henkel Loctite E-309 Datasheet Henkel Loctite E-309

Information provided by Gluespec
  • Description for Henkel Loctite E-309

    • Single component • Toughened epoxy • Bonds well to metals, thermoset and composite materials • High strength • Excellent impact resistance • Excellent peel strength • Excellent heat resistance •<br/>

    *See Terms of Use Below

    Brand Loctite, Bondmaster
    Chemical Resistance Alcohols, Chemical Resistance: Halogenated solvents, Chemical Resistance: Fluid Resistance: Water, Aqueous, Hydrocarbons, Salt spray
    Application Type Bond, Pot
    1 Part or 2 Part 1-Part
    Material Form Paste
    Substrate Aluminum, Copper, Glass, Carbide, Plastic, Steel, Stainless Steel, Brass, Ferrite, SMC Plastic, Metal, Thermoset Plastics
    Manufacturer Henkel
    Chemistry Epoxy, Toughened
    Cure Method Heat
    Cure Temperature (°C) 150, 180, 200
    Cure Time (min) 45, 17, 12
    Viscosity (cPs) Medium, 150,000, Partial Flow, Self-leveling
    Color Cream
    High Temperature Resistance (°C) 204
    Low Temperature Resistance (°C) -85
    Volume Resistivity (O) 3.0e15 (ohms/cm)
  • Technical Data for Henkel Loctite E-309

    Overview
    • Chemical Resistance
      • Chemical Resistance : Fluid Resistance : Water Resistance - Water
      • Chemical Resistance - Alcohols, Aqueous, Hydrocarbons, Salt spray
      • Chemical Resistance : Relative Solvent Resistance - Halogenated solvents
    • Application Type
    • 1 Part or 2 Part
      • 1-Part
    • Material Form
      • Paste
    • Substrate
    • Industry
    • Chemistry
    • Cure Method
      • Heat
    • Color
      • Off-White - Cream
    • Brand
      • Loctite
      • Bondmaster
    • Also Known As
      • Old Name - ESP309
    Specifications
    Cure Specs
    Cure Temperature (°C) 150, 180, 200
    Cure Time (min) 45, 17, 12
    Viscosity (cPs) Medium, 150,000, Partial Flow, Self-leveling Test Method
    Set Time (min) 2.33, 0.67, 0.33 Test Method
    Work / Pot Time (min) 1,440 Test Method
    Bond Strength
    Structural/Load-Bearing Structural
    General Bond Strength (psi) Outstanding
    Peel Strength (piw) 24 (Pli), Excellent Test Method
    Shear Strength (psi) 6,000, 5,800, 5,800, 4,000, 3,800, 5,800, 5,800, 1,800 Test Method
    Material Resistance
    High Temperature Resistance (°C) 204
    Impact Resistance Excellent impact resistance
    Low Temperature Resistance (°C) -85
    Moisture/Humidity Resistance Excellent Heat resistance
    Vibration Resistance/Shock Resistance Excellent vibration resistance
    Conductivity
    Filler Non-Metallic, Inorganic
    Dielectric Strength (V/mil) 1,400
    Thermal Conductivity (W/m°K) 0.55
    Volume Resistivity (O) 3.0e15 (ohms/cm)
    Other Properties
    Glass Transition Temp (Tg) (°C) 113
    Specific Gravity 1.500 Test Method
    Coefficient of Thermal Expansion (CTE) 58.6e-6 (in./ in/°C), 176e-6 (in./ in/°C) Test Method
    Flash Point (°F) >199.4
    % Solids (%) 100
    Business Information
    Shelf Life Details Store product refrigerated, in a dry location, in unopened containers at a temperature between 2 to 8 C (36 to 46 F) unless otherwise labeled. Optimal storage is at the lower half of this temperature range. To prevent contamination of unused product, do not return any material to its original container. For further specific shelf life information, contact Application Engineering at (860) 571-5100.
    Shelf Life Temperature (°F) 36 to 46
  • Best Practices for Henkel Loctite E-309

    *See Terms of Use Below

    1. Surface Preparation

      For optimum bond strength, substrate surfaces must be dry and preferably clean. Chemical treatment of metallic surfaces gives optimum durability, but a simple abrade and degrease process may often be adequate. The high bond strength achieved even on oily surfaces is sometimes beneficial where removal of oil is not practical.

    2. Clean-Up

      Unreacted epoxy can be cleaned using acetone, isopropanol, or MEK.

  • Comparable Materials for Henkel Loctite E-309

    *See Terms of Use Below

    Spec Engine® Results

Popular Articles

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Read Article

Electrically Conductive Adhesives

Read Article

Epoxies in the Medical Device Industry

Read Article

Testing the effectiveness of surface treatments

Read Article

Sponsored Articles

Unique Advantages of Contact Adhesives

Read Article

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Read Article

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Read Article

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Read Article

Featured Ads

Gluespec Poll

When you're researching or sourcing materials online, what device are you using?
Set Time Test Methods
Set Time Set Temperature
2.33 min 150°C
0.67 min 180°C
0.33 min 200°C
Viscosity Test Methods
Viscosity Temperature
Medium
150,000 cPs 25°C
Partial Flow
Self-leveling
Work / Pot Time Test Methods
Work / Pot Time Test Method
1,440 min The work life refers to the use life of the epoxy after application of the adhesive to the bonding surface
Peel Strength Test Methods
Peel Strength Substrate Test Method
24 (Pli) Steel/Steel ASTM 1876
Excellent
Shear Strength Test Methods
Shear Strength Substrate Test Method
6,000 psi Steel/Steel ASTM D1002
5,800 psi Aluminum/Aluminum ASTM D1002
5,800 psi Stainless steel/Stainless steel ASTM D1002
4,000 psi Copper/Copper ASTM D1002
3,800 psi Brass/Brass ASTM D1002
5,800 psi Carbide/Carbide ASTM D1002
5,800 psi Ferrite/Ferrite ASTM D1002, Denotes substrate failure of the bonded material, not the adhesive joint.
1,800 psi SMC Plastic/SMC Plastic ASTM D1002, Denotes substrate failure of the bonded material, not the adhesive joint.
Coefficient of Thermal Expansion (CTE) Test Methods
Coefficient of Thermal Expansion (CTE) CTE Test Method
58.6e-6 (in./ in/°C) Below Tg
176e-6 (in./ in/°C) Above Tg
Specific Gravity Test Methods
Specific Gravity Temperature
1.500 25°C