3M Hook and Loop Fastener SJ3401

3M Hook and Loop Fastener SJ3401 Datasheet
  • Description for 3M Hook and Loop Fastener SJ3401

    It is alternatives to zippers, screws, snaps, hooks and more. They offer greater design flexibility, faster product<br/>assembly, smoother and cleaner exterior surfaces and improved product performance in many applications

    *See Terms of Use Below

    Brand Bumpon
    Application Type Bumpons
    1 Part or 2 Part 1 Part
    Material Form Strip
    Substrate Fabric
    Industry Alternatives to screws
    Manufacturer 3M
    Chemistry Woven Nylon
    Color Black, Beige, White
    High Temperature Resistance (°C) 38
    Low Temperature Resistance (°C) 20
    Durability Very durable
    Key Specifications CID (United States Government Commercial Item Description): A-A-55126A: Type II, Class 1, Mil-Spec (United States Military Standard): F-21840: MIL-F-21840, Type IA, II and III Class 3; meet the physical requirements of CID A-A-55126A, Type II, Class 1.
  • Technical Data for 3M Hook and Loop Fastener SJ3401

    Overview
    • Application Type
      • Bumpons
    • 1 Part or 2 Part
      • 1 Part or 2 Part - 1 Part
    • Material Form
      • Strip
    • Substrate
      • Fabric
      • Other - Smoother exterior surfaces , Cleaner exterior surfaces
    • Industry
      • Mechanical Fastening Parts - Alternatives to screws
      • Textiles - Garments
      • Other - Many applications, Alternatives to hooks, Alternatives to snaps, Alternatives to zippers
    • Chemistry
      • Nylon - Woven Nylon
    • Cure Method
      • None
    • Color
      • Black
      • Brown - Beige
      • White
    • Key Specifications
      • CID (United States Government Commercial Item Description): A-A-55126A: Type II, Class 1
      • Mil-Spec (United States Military Standard): F-21840: Type IA, II and III Class 3 - MIL-F-21840, Type IA, II and III Class 3; meet the physical requirements of CID A-A-55126A, Type II, Class 1.
    • Brand
      • Bumpon
    Specifications
    Bond Strength
    Peel Strength (piw) 2.0 (lb./inch), 2.2 (Lbs/inch), 7.5 (Lbs/inch) Test Method
    Shear Strength (psi) 22 (Lbs/in2) Test Method
    Tensile Strength (psi) 11 (Lbs/in2) Test Method
    Material Resistance
    High Temperature Resistance (°C) 38
    Low Temperature Resistance (°C) 20
    Hardness
    Durability Very durable
    Dimensional Stability Maximum
    Flexibility Flexibility
    Business Information
    Shelf Life Details Shelf Life when stored in original packaging at 72°F (22°C) and 50% RH
    Shelf Life Temperature (°F) 72
    Shelf Life (mon) 24
  • Best Practices for 3M Hook and Loop Fastener SJ3401

    *See Terms of Use Below

    1. Application

      To obtain optimum bond to any surface, both the fasteners and the target surfaces should have equilibrated for a minimum of one hour at temperatures between 68°F (20°C) to 100°F (38°C) before application. The liner protecting the adhesive is removed and preferably without touching the adhesive, the fastener is applied to the substrate. Exposure of the adhesive to ambient conditions without the protective liner, before applying to the surface, should be minimized as initial adhesive tack may decrease. Flexible materials should be lying on a hard flat surface so as to permit uniform adhesive contact with the surface. Use of a rubber hand roller, press platen or similar device is recommended to ensure full adhesive contact or wetout with the substrate surface. Approximately 4.5 pounds of force per square inch, (310 grams per square centimeter) is recommended to increase adhesive contact, improving bond strength. For all adhesive applications, it is important to ensure that the edges are rolled down to reduce the chance of edge lifting.

      Plain backed: The plain backed 3M hook and loop fasteners are most commonly sewn into their applications. Liquid or hot melt adhesives and staples are other forms of attachment that can be utilized.

      Sewing: Although the selvedge edge was initially developed for stitching on, customers often find that they get better anchorage when stitching through the 3M hook and loop portions of the fastener – this may be application dependant. The type of thread and stitch type is also best determined based on individual application, however, the fastener should be stitched on all edges for the best seam strength. Typically, special machine adjustments are not necessary when using our 3M hook and loop fasteners

    2. Surface Preparation

      Highly textured surfaces may reduce the ultimate adhesion levels and care should be given to minimize the surface texture or roughness. Adhesive backed fasteners should be applied to surfaces that are clean, dry and free of oil, grease, dust, mold release agents or surface contaminants that could reduce the adhesion. It is recommended to remove any surface contaminants that may reduce adhesion by using a method suited for the type and quantity of surface contaminants present. Isopropal alcohol is a good general use solvent for cleaning contaminants from surfaces for example.

      In exceptional cases, especially when removing silicone mold release agents or on rough, porous surfaces, it may be necessary to lightly abrade the surface, use an adhesion promoter, or surface sealer to optimize the adhesive bond to the substrate. The selection of abrasion, priming or sealing methods will depend upon the substrates and the environmental conditions the product will be exposed to during use.

  • Comparable Materials for 3M Hook and Loop Fastener SJ3401

    *See Terms of Use Below

    Spec Engine® Results

Questions about this material?

Get personal assistance with your specific application needs.

Your Profile Edit
  1. cdffb57a-eed1-4696-b151-9e75f863b0a2
  2. cdffb57a-eed1-4696-b151-9e75f863b0a2

Popular Articles

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Read Article

Testing the effectiveness of surface treatments

Read Article

Sponsored Articles

Unique Advantages of Contact Adhesives

Read Article

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Read Article

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Read Article

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Read Article
Information provided by Gluespec

Why Register?

  • View Technical Details
  • View Test Methods
  • View Key Specifications
  • View Similar Materials
  • Save your Project Searches

Already registered? Sign in.

Questions? Learn more about Gluespec

Gluespec Poll

When you're researching or sourcing materials online, what device are you using?
Peel Strength Test Methods
Peel Strength Type Test Method
2.0 (lb./inch) T-Peel Strength 12 inches per minute, Width, Unless stated, typical system performance characteristics were measured under controlled laboratory conditions of 72°F (22°C) and 50% relative humidity. The user should evaluate products in the actual application to ensure suitable performance for the intended use.
2.2 (Lbs/inch) 90° Peel 12 inches per minute, Width, Unless stated, typical system performance characteristics were measured under controlled laboratory conditions of 72°F (22°C) and 50% relative humidity. The user should evaluate products in the actual application to ensure suitable performance for the intended use.
7.5 (Lbs/inch) Cleavage 12 inches per minute, Width, Unless stated, typical system performance characteristics were measured under controlled laboratory conditions of 72°F (22°C) and 50% relative humidity. The user should evaluate products in the actual application to ensure suitable performance for the intended use.
Tensile Strength Test Methods
Tensile Strength Type Test Method
11 (Lbs/in2) Dynamic Tensile Strength Unless stated, typical system performance characteristics were measured under controlled laboratory conditions of 72°F (22°C) and 50% relative humidity. The user should evaluate products in the actual application to ensure suitable performance for the intended use.
Shear Strength Test Methods
Shear Strength Type Test Method
22 (Lbs/in2) Dynamic shear strength Unless stated, typical system performance characteristics were measured under controlled laboratory conditions of 72°F (22°C) and 50% relative humidity. The user should evaluate products in the actual application to ensure suitable performance for the intended use.