Brand Bumpon Application Type Bumpons 1 Part or 2 Part 1 Part Material Form Strip Substrate Nylon Hook to Nylon Loop Manufacturer 3M Cure Method Pressure Sensitive Color Black, Beige, White Durability Very durable Key Specifications CID (United States Government Commercial Item Description): CID A-A-55126A: Type II, Class 1, Mil-Spec (United States Military Standard): F-21840: MIL-F-21840, Type IA, II and III Class 3; meet the physical requirements of CID A-A-55126A, Type II, Class 1.
Technical Data for 3M Hook Fastener SJ3402
1 Part or 2 Part
- 1 Part or 2 Part - 1 Part
- Nylon - Nylon Hook to Nylon Loop
- Tape Backing - Woven nylon
- Pressure Sensitive (min) - Pressure Sensitive
- Brown - Beige
- CID (United States Government Commercial Item Description): CID A-A-55126A: Type II, Class 1
- Mil-Spec (United States Military Standard): F-21840: Type IA, II and III Class 3 - MIL-F-21840, Type IA, II and III Class 3; meet the physical requirements of CID A-A-55126A, Type II, Class 1.
Peel Strength (piw) 3.5 (g/cm), 3.9 (g/cm) Test Method Shear Strength (psi) 10 (pounds force/square inch), 10 Test Method Cleavage Strength (psi) 0 13.1 (g/cm) Test Method Tensile Strength (psi) 8, 5 Test Method
Durability Very durable Dimensional Stability Maximum Flexibility Fexible
Shelf Life Details Shelf Life when stored in original packaging at 72°F (22°C) and 50% RH is 24 months. Shelf Life Temperature (°F) 72 Shelf Life (mon) 24
Best Practices for 3M Hook Fastener SJ3402
Attachment Procedure: To obtain optimum bond to any surface, both the fasteners and the target surfaces should have equilibrated for a minimum of one hour at temperatures between 68°F (20°C) to 100°F (38°C) before application. The liner protecting the adhesive is removed and preferably without touching the adhesive, the fastener is applied to the substrate. Exposure of the adhesive to ambient conditions without the protective liner, before applying to the surface, should be minimized as initial adhesive tack may decrease. Flexible materials should be lying on a hard at surface so as to permit uniform adhesive contact with the surface. Use of a rubber hand roller, press platen or similar device is recommended to ensure full adhesive contact or wet- out with the substrate surface. Approximately 4.5 pounds of force per square inch, (310 grams per square centimeter) is recommended to increase adhesive contact, improving bond strength. For all adhesive applications, it is important to ensure that the edges are rolled down to reduce the chance of edge lifting.
Plain backed: The plain backed 3M hook and loop fasteners are most commonly sewn into their applications. Liquid or hot melt adhesives and staples are other forms of attachment that can be utilized.
Sewing: Although the selvedge edge was initially developed for stitching on, customers often nd that they get better anchorage when stitching through the 3M hook and loop portions of the fastener – this may be application dependant. The type of thread and stitch type is also best determined based on individual application, however, the fastener should be stitched on all edges for the best seam strength. Typically, special machine adjustments are not necessary when using our 3M hook and loop fasteners
Highly textured surfaces may reduce the ultimate adhesion levels and care should be given to minimize the surface texture or roughness. Adhesive backed fasteners should be applied to surfaces that are clean, dry and free of oil, grease, dust, mold release agents or surface contaminants that could reduce the adhesion. It is recommended to remove any surface contaminants that may reduce adhesion by using a method suited for the type and quantity of surface contaminants present. Isopropal alcohol is a good general use solvent for cleaning contaminants from surfaces for example. In exceptional cases, especially when removing silicone mold release agents or on rough, porous surfaces, it may be necessary to lightly abrade the surface, use an adhesion promoter, or surface sealer to optimize the adhesive bond to the substrate. The selection of abrasion, priming or sealing methods will depend upon the substrates and the environmental conditions the product will be exposed to during use.
Comparable Materials for 3M Hook Fastener SJ3402
Spec Engine® Results
Questions about this material?
Get personal assistance with your specific application needs.
Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of MaterialsRead Article
Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:Read Article
Shear Strength Test Methods
|Shear Strength||Type||Substrate||Test Method|
|10 (pounds force/square inch)||Dynamic shear strength||ASTM D5169|
|10 psi||Dynamic shear strength||Nylon Hook to Nylon Loop||Run at 12 inches per minute|
Tensile Strength Test Methods
|Tensile Strength||Type||Substrate||Test Method|
|8 psi||Dynamic Tensile Strength|
|5 psi||Dynamic Tensile Strength||Nylon Hook to Nylon Loop||Run at 12 inches per minute|
Peel Strength Test Methods
|Peel Strength||Type||Substrate||Test Method|
|3.5 (g/cm)||T-Peel Adhesion||Nylon Hook to Nylon Loop||Run at 12 inches per minute, width|
|3.9 (g/cm)||90° Peel Adhesion||Nylon Hook to Nylon Loop||Run at 12 inches per minute; width|
Cleavage Strength Test Methods
|Cleavage Strength||Substrate||Test Method|
|0 psi 13.1 (g/cm)||Nylon Hook to Nylon Loop||width|