• Description for 3M SJ5816

    Black and brown ▪ Excellent skid-resistance, high coefficient of friction. ▪ Excellent cushioning properties. ▪ Excellent abrasion resistance. ▪ Vibration and shock damping.

    *See Terms of Use Below

    Brand Bumpon
    Application Type Bumpons
    1 Part or 2 Part 1 Part
    Material Form Rollstock
    Substrate Aluminum, Polyethylene, Polystyrene, Low Surface Energy, ABS, Polypropylene, Stainless Steel, Many low surface energy surfaces
    Industry Die cut into circles or squares for use as skid-resistant feet on hand held , Cushions or spacers within electronic devices, Web feed machinery, Door kick pads, Die cut into circles or squares for use as skid-resistant feet on desktop computers, Calculators, Roll covering for other web feed machinery, Electric housewares, Electronic equipment, Desk top equipment
    Manufacturer 3M
    Chemistry Natural Rubber, Polyurethane
    Cure Method Pressure Sensitive
    Color Black, Brown, Opaque
    Ozone Resistance Ozone resistance
    Relative Solvent Resistance Chemical Resistance: Good, Chemical Resistance: 5% Detergent in water, Chemical Resistance: 25% Ammonia in water, Chemical Resistance: Bleach, Chemical Resistance: Hydrochloric Acid (1 normal solution), Chemical Resistance: Diesel Fuel, Chemical Resistance: Auto Oil, Chemical Resistance: Isopropyl Alcohol, Chemical Resistance: Heptane, Chemical Resistance: Toluol, Chemical Resistance: Lacquer Thinner, Chemical Resistance: Good
    High Temperature Resistance (°C) 66, 107
    Low Temperature Resistance (°C) -34 to 0
    Other Resistance Excellent skid resistance, Excellent marring resistance, Excellent staining resistance, Oxygen, Excellent cushioning properties
    Shore M Hardness 72
    Density (g/cm³) 1.300
    Key Specifications UL (Underwriters Laboratory), ULC (Underwriters Laboratories of Canada), NFPA (National Fire Protection Association): UL Classification UL94HB
  • Technical Data for 3M SJ5816

    Overview
    • Application Type
      • Bumpons
    • 1 Part or 2 Part
      • 1 Part or 2 Part - 1 Part
    • Material Form
      • Rollstock
    • Substrate
      • Low Surface Energy - Many low surface energy surfaces
      • Aluminum
      • Plastic - ABS
      • Polyethylene (LDPE, HDPE) - Polyethylene
      • Polystyrene (PS) - Polystyrene
      • Polypropylene
      • Stainless Steel
      • Other - Powder coated paints, High Surface Energy, A wide variety of surfaces
    • Industry
      • Textiles - Textile
      • Electronics - Calculators, Electric housewares, Electronic equipment, Desk top equipment, Cushions or spacers within electronic devices
      • Telecom / Datacom - Die cut into circles or squares for use as skid-resistant feet on hand held
      • Storage & Graphics - Die cut into circles or squares for use as skid-resistant feet on desktop computers
      • Industrial - Roll covering for textile industry
      • Machinery - Web feed machinery, Roll covering for other web feed machinery
      • Medical - Medical devices
      • Construction
      • Construction Door - Door kick pads
      • Other - Die cut for gasket application, Skid-resistant surface on floor, Anti-chafe protection, Corner protection strips., Selective masking for sandblast operation, Spacer or stop to prevent surface damage, Anti-rattle spacer to fill gaps, dampen noise and reduce vibration, Die cut cushioning stop for cabinetry
    • Chemistry
    • Application Method
      • Contact
      • Other - Easy application
    • Cure Method
      • Pressure Sensitive (min) - Pressure Sensitive
    • Color
      • Black
      • Brown
      • Other - Opaque
    • Key Specifications
      • UL (Underwriters Laboratory), ULC (Underwriters Laboratories of Canada), NFPA (National Fire Protection Association): UL 94 HB - UL Classification UL94HB
    • Brand
      • Bumpon
    Specifications
    Cure Specs
    Application Temperature (°F) 40 to 125
    Bond Strength
    General Bond Strength (psi) Excellent, Excellent initial adhesion
    Peel Strength (piw) Good, Good, 25 (oz. per 1/2 inch), 25 (oz. per 1/2 inch), 25 (oz. per 1/2 inch), 22 (oz. per 1/2 inch), 22 (oz. per 1/2 inch) Test Method
    Shear Strength (psi) Excellent, Fair, Poor Test Method
    Tensile Strength (psi) 600 (lb/in2) Test Method
    Material Resistance
    Ozone Resistance Ozone resistance
    Abrasion Resistance Excellent abrasion resistance., 1.7 to 1.9 (g/1000 cycles) Test Method
    Environmental Resistance Long aging resiliency
    High Temperature Resistance (°C) 66, 107 Test Method
    Low Temperature Resistance (°C) -34 to 0
    Other Resistance Excellent skid resistance, Excellent marring resistance, Excellent staining resistance, Oxygen, Excellent cushioning properties Test Method
    Conductivity
    Dielectric Strength (V/mil) 200 Test Method
    Hardness
    Shore A Hardness 65, 70 Test Method
    Shore M Hardness 72 Test Method
    Elongation (%) 100 Test Method
    Flexibility High tack
    Other Properties
    Density (g/cm³) 1.300
    Business Information
    Shelf Life Details The shelf life of 3M™ Bumpon™ Protective Products is 18 months from the date of manufacture when stored in the original packaging materials and stored at 16-27°C (60-80°F) and 50% relative humidity.
    Shelf Life Temperature (°F) 61 to 81
    Shelf Life Type From date of manufacture.
    Shelf Life (mon) 18
  • Best Practices for 3M SJ5816

    *See Terms of Use Below

    1. Surface Preparation

      To obtain maximum adhesion, surfaces must be unified, dry and free of contaminants. Surface contact is essential to adhesive performance. To maximize contact on a substrate: Clean surfaces with low strength solvent such as isopropyl alcohol (rubbing alcohol) or heptane. Note: Be sure to follow the solvent manufacturer’s precautions and directions for use when using solvents.

    2. Application

      Apply firm pressure to help increase the cold flow and contact of the adhesive with the substrate.

      Allow time (dwell) to increase the surface contact and adhesion (see illustration below).

    3. Testing

      Product selection is ultimately the responsibility of the user and should conduct their own tests under actual use and storage conditions to determine whether product is fit for a particular purpose and user’s method of application.

  • Comparable Materials for 3M SJ5816

    *See Terms of Use Below

    Spec Engine® Results

Questions about this material?

Get personal assistance with your specific application needs.

Your Profile Edit
  1. 334e7e67-48c1-487d-ac1e-dbc4e6f1329e
  2. 334e7e67-48c1-487d-ac1e-dbc4e6f1329e

Popular Articles

Testing the effectiveness of surface treatments

Read Article

Characteristics of MMAs

Read Article

The effectiveness of adhesives in the wind power industry

Read Article

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Read Article

Sponsored Articles

Unique Advantages of Contact Adhesives

Read Article

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Read Article

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Read Article

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Read Article
Information provided by Gluespec

Why Register?

  • View Technical Details
  • View Test Methods
  • View Key Specifications
  • View Similar Materials
  • Save your Project Searches

Already registered? Sign in.

Questions? Learn more about Gluespec

Gluespec Poll

What level of expertise do you have in specialty chemicals like adhesives, sealants, conformal coatings, etc.?
Shear Strength Test Methods
Shear Strength Type Test Temperature
Excellent Static Shear Strength 24°C
Fair Static Shear Strength 49°C
Poor Static Shear Strength 70°C
Tensile Strength Test Methods
Tensile Strength Test Method
600 (lb/in2) ASTM-D-412, Die A
Peel Strength Test Methods
Peel Strength Type Substrate Test Time Test Method
Good Low Surface Energy
Good High Surface Energy
25 (oz. per 1/2 inch) 90° Peel Strenth Polypropylene 4,320 min TM-2011, 72 hour dwell, 1/2 inch wide samples pulled at 12 inches per minute. Testing completed using Bumpon resilient rollstock products SJ-5816, SJ-6016, and SJ-6216.
25 (oz. per 1/2 inch) 90° Peel Strenth Polystyrene 4,320 min TM-2011, 72 hour dwell, 1/2 inch wide samples pulled at 12 inches per minute. Testing completed using Bumpon resilient rollstock products SJ-5816, SJ-6016, and SJ-6216.
25 (oz. per 1/2 inch) 90° Peel Strenth ABS 4,320 min TM-2011, 72 hour dwell, 1/2 inch wide samples pulled at 12 inches per minute. Testing completed using Bumpon resilient rollstock products SJ-5816, SJ-6016, and SJ-6216.
22 (oz. per 1/2 inch) 90° Peel Strenth Stainless Steel 4,320 min TM-2011, 72 hour dwell, 1/2 inch wide samples pulled at 12 inches per minute. Testing completed using Bumpon resilient rollstock products SJ-5816, SJ-6016, and SJ-6216.
22 (oz. per 1/2 inch) 90° Peel Strenth Aluminum 4,320 min TM-2011, 72 hour dwell, 1/2 inch wide samples pulled at 12 inches per minute. Testing completed using Bumpon resilient rollstock products SJ-5816, SJ-6016, and SJ-6216.
Abrasion Resistance Test Methods
Abrasion Resistance Test Method
Excellent abrasion resistance.
1.7 to 1.9 (g/1000 cycles) Taber H 18, 1 kg, ASTM-C-501
Other Resistance Test Methods
Other Resistance Test Method
Excellent skid resistance
Excellent marring resistance
Excellent staining resistance 24 hrs. @ 158°F against white paint, 7 days exposed to UV
Oxygen 30 days @50 ppm ozone
Excellent cushioning properties 30 days @50 ppm ozone
High Temperature Resistance Test Methods
High Temperature Resistance Test Method
66°C
107°C Intermittent exposure
Dielectric Strength Test Methods
Dielectric Strength Test Method
200 V/mil ASTM-D-1000
Elongation Test Methods
Elongation Test Method
100 % ASTM-D-412, Die A
Shore A Hardness Test Methods
Shore A Hardness Shore Hardness Test Method
65
70 ASTM-D-2240
Shore M Hardness Test Methods
Shore M Hardness Shore Hardness Test Method
72