Elantas (Altana) FR-1810 Datasheet Elantas (Altana) FR-1810

Information provided by Gluespec
  • Description for Elantas (Altana) FR-1810

    A flexible two-component, low exotherm, flame retardant, long pot life epoxy potting and casting system with excellent handling properties. It is filled with a non abrasive filler to reduce wear on machine metering/dispensing equipment.

    *See Terms of Use Below

    Brand Cytec
    Application Type Casting, Potting, Encapsulation
    1 Part or 2 Part 2-Part
    Material Form Liquid
    Manufacturer Elantas (Altana)
    Chemistry Epoxy, Non-flammable: Flame-retardant
    Cure Method Resin/Hardener
    Cure Temperature (°C) 25, 80
    Viscosity (cPs) 8,000, 3,800
    Color Black
    Volume Resistivity (O) 7.1e13 (ohm-cm)
    Key Specifications Comply with Directive 2011/65/EU, UL (Underwriters Laboratory), ULC (Underwriters Laboratories of Canada), NFPA (National Fire Protection Association): UL 94: UL94 V-0, 4.8 mm
  • Technical Data for Elantas (Altana) FR-1810

    Overview
    • Application Type
    • 1 Part or 2 Part
      • 2-Part
    • Material Form
      • Liquid
    • Chemistry
      • Non-flammable : Flame Retardant - Flame-retardant
      • Epoxy
    • Application Method
      • Dispenser - machine metering, dispensing equipment
      • Other - Hand-mix Bench Potting / Casting, Meter-mix Bench Potting / Casting, Meter-mix Vacuum Potting / Casting
    • Cure Method
      • 2-Part Cure - Resin/Hardener
    • Color
      • Black
    • Key Specifications
      • RoHS (Restriction of Hazardous Substances) - Comply with Directive 2011/65/EU
      • UL (Underwriters Laboratory), ULC (Underwriters Laboratories of Canada), NFPA (National Fire Protection Association) : UL 94 : V0 - UL94 V-0, 4.8 mm
    • Brand
      • Cytec
    Specifications
    Cure Specs
    Cure Temperature (°C) 25, 80
    Viscosity (cPs) 8,000, 3,800 Test Method
    Fixture or Handling Strength Time (min) Excellent
    Set Time (min) 130 Test Method
    Linear Shrinkage (%) 0.0006 (in/in), 0.06 Test Method
    Work / Pot Time (min) Long, 80 Test Method
    Mix Ratio 100:100 (by volume), 100:100 (by weight)
    Bond Strength
    Tensile Strength (psi) 1,325, 1,300 Test Method
    Conductivity
    Dissipation Factor 0.03200, 0.03700, 0.02100, 0.03000, 0.04000, 0.02000 Test Method
    Filler Non-abrasive filler
    Dielectric Strength (V/mil) 530 Test Method
    Dielectric Constant 4.75, 4.39, 3.87, 4.80, 4.40, 3.90 Test Method
    Thermal Conductivity (W/m°K) 0.70, 0.70 Test Method
    Surface Resistivity (O) 4.7e15 (Ohm) Test Method
    Volume Resistivity (O) 7.1e13 (ohm-cm) Test Method
    Hardness
    Shore D Hardness 80 to 85, 80 Test Method
    Elongation (%) 22, High elongation for reduced stress on components Test Method
    Flexibility Flexible
    Business Information
    Shelf Life Details CONAPOXY FR-1810 has a shelf life of 18 months from date of manufacture when stored in the original unopened containers at 20C-30C (68F-86F). CONAPOXY FR-1810 Part A and Part B contain filler that may settle during storage. It is recommended that both components be thoroughly mixed before use., Store below 25°C / 77°F in a dry controlled environment out of direct sunlight. This material should be suitable for use stored under these conditions in the original sealed containers for twelve (12) months from the date of shipment.
    Shelf Life Temperature (°F) 68 to 86, <77
    Shelf Life Type From date of manufacture, From the date of shipment
    Shelf Life (mon) 18, 12
  • Best Practices for Elantas (Altana) FR-1810

    *See Terms of Use Below

    1. Mixing

      Mix and degas individual components thoroughly, prior to use. CONAPOXY® FR-1810 Part A Resin and CONAPOXY® FR-1810 Part B Hardener contain fillers that must be redistributed homogeneously.

      Mix FR-1810 Part A and FR-1810 Part B in the ratio specified above until homogeneous. Components may be preheated up to 60°C if reduced viscosity is required. If hand-mixing, degas at >27 in. Hg before use.

    2. Curing

      Cure 32 - 48 hours at 25°C / 77°F for maximum properties – or – 3 – 4 hours @ 80°C / 176°F

      The user is responsible for determining the optimum cure conditions for his application.

  • Comparable Materials for Elantas (Altana) FR-1810

    *See Terms of Use Below

    Spec Engine® Results

Popular Articles

Testing the effectiveness of surface treatments

Read Article

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Read Article

Epoxies in the Aerospace Industry

Read Article

The effectiveness of adhesives in the wind power industry

Read Article

Sponsored Articles

Unique Advantages of Contact Adhesives

Read Article

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Read Article

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Read Article

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Read Article

Featured Ads

Top Catalog Pages for Elantas (Altana) FR-1810

Gluespec Poll

What level of expertise do you have in specialty chemicals like adhesives, sealants, conformal coatings, etc.?
Linear Shrinkage Test Methods
Linear Shrinkage Test Method Temp
0.0006 (in/in)
0.06 % ASTM D2566 25°C
Set Time Test Methods
Set Time Set Temperature Test Method
130 min 25°C Gel Time, 200 gm mass, Mixed
Viscosity Test Methods
Viscosity Test Method Temperature
8,000 cPs Mixed, initial 25°C
3,800 cPs Mixed, initial 38°C
Work / Pot Time Test Methods
Work / Pot Time Test Method Temperature
Long
80 min To reach 100,000 cps, 200 gm mass, Mixed 25°C
Tensile Strength Test Methods
Tensile Strength Test Temperature Test Method
1,325 psi
1,300 psi 25°C ASTM D412
Dielectric Constant Test Methods
Dielectric Constant Temperature Test Method
4.75 25°C @ 100 Hz
4.39 25°C @ 1 KHz
3.87 25°C @ 1 MHz
4.80 25°C ASTM D150, @ 100 Hz
4.40 25°C ASTM D150, @ 1 kHz
3.90 25°C ASTM D150, @ 1 MHZ
Dielectric Strength Test Methods
Dielectric Strength Temperature Test Method
530 V/mil 25°C ASTM D149, 1/16”
Dissipation Factor Test Methods
Dissipation Factor Temperature Test Method
0.03200 25°C @ 100 Hz
0.03700 25°C @ 1 KHz
0.02100 25°C @ 1 MHz
0.03000 25°C ASTM D150, @ 100 Hz
0.04000 25°C ASTM D150, @ 1 kHz
0.02000 25°C ASTM D150, @ 1 MHZ
Surface Resistivity Test Methods
Surface Resistivity Temperature Test Method
4.7e15 (Ohm) 25°C ASTM D257
Thermal Conductivity Test Methods
Thermal Conductivity Test Method
0.70 W/m°K
0.70 W/m°K ASTM D5930
Volume Resistivity Test Methods
Volume Resistivity Temp (°C) Test Method
7.1e13 (ohm-cm) 25°C ASTM D257
Elongation Test Methods
Elongation Test Method
22 % ASTM D412, 25°C
High elongation for reduced stress on components
Shore D Hardness Test Methods
Shore D Hardness Shore Hardness Test Method Hardness Temperature
80 to 85
80 ASTM D2240 25°C