Elantas (Altana) Conathane CE-1155-35 Datasheet Elantas (Altana) Conathane CE-1155-35

Information provided by Gluespec
  • Description for Elantas (Altana) Conathane CE-1155-35

    A two-component, high-performance, solvent-based polyurethane coating system for protecting circuit assemblies in adverse environments.

    *See Terms of Use Below

    Brand Conathane, Cytec
    Chemical Resistance Excellent, Chemical Resistance: Excellent solvent resistance
    Application Type Coat
    1 Part or 2 Part 2-Part
    Material Form Liquid
    Industry Electrical, Protecting circuit assemblies
    Manufacturer Elantas (Altana)
    Chemistry Solvent-based, Polyurethane
    Cure Method Part A/Part B
    Cure Temperature (°C) 25, 60
    Cure Time (min) 7,200 to 10,080, 180
    Viscosity (cPs) 25
    Color Clear
    Fungus Resistance Fungus resistance
    High Temperature Resistance (°C) 130
    Low Temperature Resistance (°C) -65
    Volume Resistivity (O) 1.2e16 (ohms/cm)
    Key Specifications IPC-CC-830B, Mil-Spec (United States Military Standard): I-46058-C: MIL-STD-810B; MIL-I-46058C, Type UR, Mil-Spec (United States Military Standard): MIL-STD-810B; MIL-I-46058C, Type UR
  • Technical Data for Elantas (Altana) Conathane CE-1155-35

    Overview
    • Chemical Resistance
      • Chemical Resistance - Excellent
      • Chemical Resistance : Relative Solvent Resistance - Excellent solvent resistance
    • Application Type
    • 1 Part or 2 Part
      • 2-Part
    • Material Form
      • Liquid
    • Industry
      • Electronics - Electrical, Protecting circuit assemblies
    • Application Method
      • Brush
      • Spray
      • Dip
    • Cure Method
      • 2-Part Cure - Part A/Part B
    • Color
      • Clear / Transparent - Clear
    • Key Specifications
      • IPC (Association Connecting Electronics Industries) - IPC-CC-830B
      • Mil-Spec (United States Military Standard) : I-46058-C : Type UR - MIL-STD-810B; MIL-I-46058C, Type UR
      • Mil-Spec (United States Military Standard) : STD-810B - MIL-STD-810B; MIL-I-46058C, Type UR
    • Brand
      • Conathane
      • Cytec
    Specifications
    Cure Specs
    Cure Temperature (°C) 25, 60
    Cure Time (min) 7,200 to 10,080, 180
    Viscosity (cPs) 25 Test Method
    Tack Free Time (min) 120 to 180, 25 to 30 Test Method
    Work / Pot Time (min) 480 to 600 Test Method
    Mix Ratio 1:1 (by volume)
    Material Resistance
    Fungus Resistance Fungus resistance
    High Temperature Resistance (°C) 130
    Low Temperature Resistance (°C) -65
    Moisture/Humidity Resistance Moisture/humidity resistance
    Conductivity
    Dissipation Factor 0.01600 Test Method
    Insulation Resistance (O) >2.5e13 (ohms), Insulation resistance Test Method
    Dielectric Strength (V/mil) >1500 Volts
    Dielectric Constant 3.42 Test Method
    Surface Resistivity (O) 5.7e14 (ohms) Test Method
    Volume Resistivity (O) 1.2e16 (ohms/cm) Test Method
    Hardness
    Flexibility Passes Test Method
    Other Properties
    Flash Point (°F) 89.6, 55.4 Test Method
    % Solids (%) 35, 37, 30
    Business Information
    Shelf Life Details CONATHANE CE-1155-35 should be stored at temperatures of 20°C-30ºC (68ºF-86ºF) in tightly closed containers. If containers are opened and the contents only partially used, the containers should be flushed with dry nitrogen (see CONAP® Dri-Purge) or dry air before being resealed.;The shelf life of CONATHANE CE-1155-35 Part A and Part B is 15 months from date of manufacture when stored in the original, unopened containers at the temperatures recommended above.
    Shelf Life Temperature (°F) 68 to 86
    Shelf Life Type From date of manufacture
    Shelf Life (mon) 15
  • Best Practices for Elantas (Altana) Conathane CE-1155-35

    *See Terms of Use Below

    1. Application

      CONATHANE® CE-1155-35 is a high-performance conformal coating based on raw materials of the highest purity. The ultimate performance of the cured coating on an assembly is dependent on process controls used in application of the coating.

      Specific substrates to be used in production should be thoroughly evaluated. For example: there may be differences in performance on G-10, G-1,or other laminates. Cleanliness of the substrates is a major factor in promoting adhesion and preventing under-film corrosion. Boards MUST be clean, oil-free, and dry. Request Technical Bulletin C-115 for specific cleaning recommendations prior to coating.

      Because CE-1155-35 is a solvent-based system, it is not recommended that more than 2 to 2.5 mils of wet film thickness be applied during any one application. This will prevent the possibility of solvent entrapment. If more than one coat is desired, allow 2 hours at room temperature or 2 hour at 60°C before re-coating.

      CE-1155-35 can be applied by spraying, dipping, or brushing and may be thinned with CONAP® S-8 solvent to lower the viscosity or to adjust film thickness.

  • Comparable Materials for Elantas (Altana) Conathane CE-1155-35

    *See Terms of Use Below

    Spec Engine® Results

    Closest Results from this Manufacturer

Popular Articles

Testing the effectiveness of surface treatments

Read Article

What are the Types of Adhesive Sealants? An In-Depth Q&A

Read Article

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Read Article

Primers and Surface Preparation for Proper Adhesive Wetting & Bonding - Q&A

Read Article

Sponsored Articles

Unique Advantages of Contact Adhesives

Read Article

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Read Article

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Read Article

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Read Article

Featured Ads

Top Catalog Pages for Elantas (Altana) Conathane CE-1155-35

Gluespec Poll

What level of expertise do you have in specialty chemicals like adhesives, sealants, conformal coatings, etc.?
Tack Free Time Test Methods
Tack Free Time Tack Free Temperature
120 to 180 min 25°C
25 to 30 min 60°C
Viscosity Test Methods
Viscosity Temperature
25 cPs 25°C
Work / Pot Time Test Methods
Work / Pot Time Temperature
480 to 600 min 25°C
Dielectric Constant Test Methods
Dielectric Constant Temperature Test Method
3.42 25°C Dielectric constant @ 1 MHz
Dissipation Factor Test Methods
Dissipation Factor Temperature Test Method
0.01600 25°C Dissipation Factor @ 1 MHz
Insulation Resistance Test Methods
Insulation Resistance Temperature
>2.5e13 (ohms) 25°C
Insulation resistance
Surface Resistivity Test Methods
Surface Resistivity Temperature
5.7e14 (ohms) 25°C
Volume Resistivity Test Methods
Volume Resistivity Temp (°C)
1.2e16 (ohms/cm) 25°C
Flexibility Test Methods
Flexibility Test Method
Passes MIL-I-46058C
Flash Point Test Methods
Flash Point Test Method
32.0°C TCC
13.0°C TCC