Bostik Hydroment 1900 Epoxy-Modified Grout and Mortar Admixture Datasheet Bostik Hydroment 1900 Epoxy-Modified Grout and Mortar Admixture

Information provided by Gluespec
  • Description for Bostik Hydroment 1900 Epoxy-Modified Grout and Mortar Admixture

    Epoxy modified grout & mortar admixture.

    *See Terms of Use Below

    Chemical Resistance Cleaners, Chemical Resistance: Other hydrocarbon solvents, Chemical Resistance: Dilute acids, De-icing salts, Diesel fuel, Household foods, Food waste, Gasoline
    Application Type Grout and Mortar Admixture
    1 Part or 2 Part 2-Part
    Material Form Liquid
    Substrate All ceramic, Dimension stone tiles, Plywood, Ceramic tile, Granite, Quarry, Slate, Limestone
    Industry Exterior installations, Food processing, Restaurants
    Manufacturer Bostik
    Chemistry Epoxy
    Application Method Flat edge of trowel, Notch trowel
    Cure Method 2-Part Cure
    Other Resistance Freeze, Thaw
    Key Specifications ANSI (American National Standards Institute): ANSI A118.8
  • Technical Data for Bostik Hydroment 1900 Epoxy-Modified Grout and Mortar Admixture

    Overview
    • Chemical Resistance
      • Chemical Resistance - Cleaners, De-icing salts, Diesel fuel, Food waste, Gasoline, Household foods
      • Chemical Resistance : Relative Solvent Resistance - Other hydrocarbon solvents
      • Chemical Resistance : Acid Resistance - Dilute acids
    • Application Type
      • Gap Filler - Grout and Mortar Admixture
    • 1 Part or 2 Part
      • 2-Part
    • Material Form
      • Liquid
    • Substrate
      • Ceramic - Ceramic tile, All ceramic
      • Wood - Plywood
      • Stone - Dimension stone tiles, Granite, Quarry, Slate, Limestone
      • Other - Marble, Porcelain
    • Industry
      • Food & Beverage - Food processing, Restaurants
      • Industrial - Concourses, Malls, Service garages, Back splashes
      • Industrial Exterior - Exterior installations
      • Construction - Bathrooms, Counter tops, Residential kitchens, Commercial kitchens
      • Packaging - Packaging plants
      • Other - Interior installations
    • Chemistry
    • Application Method
      • Dispenser - Rubber grout float
      • Spatula/Trowel - Flat edge of trowel, Notch trowel
    • Cure Method
      • 2-Part Cure
    • Key Specifications
      • ANSI (American National Standards Institute) : A118.8 - ANSI A118.8
    Specifications
    Cure Specs
    Open Time Temperature (°C) 21
    Set Time (min) 318, 540 Test Method
    Work / Pot Time (min) 120, Excellent Test Method
    Open Time (min) 60
    Bond Strength
    Shear Strength (psi) Superior, 240, 128, 179, 439, 378, 372, 251, 263, 600, 387, 475, 300, 280 Test Method
    Compressive Strength (psi) Superior, 3,950, 6,000 Test Method
    Flexural Strength (psi) Superior
    Tensile Strength (psi) Superior, 492 Test Method
    Material Resistance
    Other Resistance Freeze, Thaw
    Business Information
    Shelf Life Details Store in a clean, dry area at temperatures between 34°F and 100°F. Shelf life is one year from date of manufacturing.
    Shelf Life Temperature (°F) 34 to 100
    Shelf Life Type From date of manufacturing
    Shelf Life (mon) 12
    Not Good For
    Don't Use With moisture sensitive stone., oriented strand board, particle board, masonite,luaun, metal, fiberglass, similar unstable substrates., plywood
  • Best Practices for Bostik Hydroment 1900 Epoxy-Modified Grout and Mortar Admixture

    *See Terms of Use Below

    1. Surface Preparation

      USE AS A SETTING SYSTEM:SURFACE PREPARATION: All surfaces must be clean, dry and smooth

      free of voids, projections, loose materials, oil, grease, sealers, curing compounds, waxes and all other surface contaminants that may inhibit proper bond. For best results, surface, mortar, and tile should be at room temperature (70°F to 75°F). Do not apply at temperatures below 60°F, or above 85°F.

      USE AS A GROUTING SYSTEM:SURFACE PREPARATION: Ensure tile is firmly set and mortar completely dry before grouting. Remove all spacers, debris or adhesive from tile joints. Application of a grout release agent may be necessary to prevent staining of tile.

    2. Application

      Apply a thin coat of properly mixed Hydroment 1900 Modified Mortar with the flat edge of trowel to achieve a good mechanical bond to the substrate. Comb additional mortar with the appropriate size notch trowel. If any evidence of skinning or setting occurs, re-comb mortar with notched trowel. Apply mortar to an area no greater than can be tiled in 20 to 30 minutes. Apply tile using a twisting motion into a fresh bed of mortar to ensure maximum contact and bond. Periodically check back of tile to ensure proper transfer (interior applications-minimum 80% coverage

      exterior, wet, or plywood applications--minimum 95% coverage). A finished mortar bed thickness of 3/32" to 1/8" is required.

      See Technical Data Sheet for more info.

      Lightly moisten tile with clean, damp sponge before grouting. Spread grout over the face of the tile using a rubber grout float. Work grout back and forth at a 45° angle to the face of the tile to ensure complete filling of the joints. Remove excess grout by holding the rubber float at a 90° angle working diagonally across the face of the tile.

    3. Mixing

      Using a slow speed mixer (<150 rpm), separately mix 1900 Emulsion Resin (Part A) and then 1900 Hardener (Part B). Mix Resin (Part A) with equal volume of Hardener (Part B) until completely and thoroughly mixed. Slowly add required amount of Hydroment Sanded Ceramic Tile Grout (25 lbs. for Single Unit

      50 lbs. for Double Unit

      250 lbs. for Industrial Unit) and mix until a smooth, uniform consistency is achieved. Allow mixture to stand 15 minutes, and re-mix prior to application. Do not retemper by adding more liquid.

      Using a slow speed mixer (<150 rpm), separately mix 1900 Emulsion Resin (Part A) and then 1900 Hardener (Part B). Mix Resin (Part A) with equal volume of Hardener (Part B) until completely and thoroughly mixed. Slowly add required amount of Hydroment Sanded Ceramic Tile Grout (25 lbs. for Single Unit

      50 lbs. for Double Unit

      250 lbs. for Industrial Unit) and mix until a smooth, uniform consistency is achieved. Allow mixture to stand 15 minutes, and re-mix prior to application. Do not re-temper by adding more liquid.

    4. Curing

      Keep all foot traffic off the installation until tile is firmly set (approximately 12 hours Set times are dependent upon temperature and humidity.

    5. Clean-Up

      USE AS A SETTING SYSTEM: Clean all tools and equipment with soap and water. Do not allow material to dry on surface of tile.

      USE AS A GROUTING SYSTEM: FINAL CLEAN UP: Depending on humidity and temperature, begin final clean up approximately 1 hour after initial cleaning. Using a damp nylon scrub pad (i.e.: 3M Doodlebug®), wipe diagonally across the face of the tile. Change water and rinse pad frequently to minimize the build up of grout haze. Never use acid cleaners as they may result in irreversible damage to the grout or tile.

  • Comparable Materials for Bostik Hydroment 1900 Epoxy-Modified Grout and Mortar Admixture

    *See Terms of Use Below

    Spec Engine® Results

    Closest Results from this Manufacturer

Popular Articles

Testing the effectiveness of surface treatments

Read Article

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Read Article

The effectiveness of adhesives in the wind power industry

Read Article

Epoxies in the Aerospace Industry

Read Article

Sponsored Articles

Unique Advantages of Contact Adhesives

Read Article

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Read Article

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Read Article

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Read Article

Featured Ads

Top Catalog Pages for Bostik Hydroment 1900 Epoxy-Modified Grout and Mortar Admixture

Gluespec Poll

Who do you read or follow for engineering news and entertainment?
Set Time Test Methods
Set Time Set Temperature Test Method
318 min 21°C Initial set
540 min 21°C Final Set
Work / Pot Time Test Methods
Work / Pot Time Test Method Temperature
120 min Pot Life 21°C
Excellent
Compressive Strength Test Methods
Compressive Strength Cure Time
Superior
3,950 psi 10,080 min
6,000 psi 40,320 min
Tensile Strength Test Methods
Tensile Strength Test Time
Superior
492 psi 10,080 min
Shear Strength Test Methods
Shear Strength Substrate Test Time Test Method
Superior
240 psi Glazed Wall Tile 86,400 sec
128 psi Ceramic Mosaic Tile 86,400 sec
179 psi Quarry Tile 86,400 sec
439 psi Glazed Wall Tile 604,800 sec
378 psi Ceramic Mosain Tile 604,800 sec
372 psi Quarry Tile 604,800 sec
251 psi Glazed to Wood 604,800 sec
263 psi Quarry to Wood 604,800 sec Min. shear values due to failure of wood substrate.
600 psi Glazed Wall Tile 2,419,200 sec
387 psi Ceramic Mosain Tile 2,419,200 sec
475 psi Quarry Tile 2,419,200 sec
300 psi Glazed to Wood 2,419,200 sec
280 psi Quarry to Wood 2,419,200 sec Min. shear values due to failure of wood substrate.