Resin Designs GT-1010 Sealing Strip Datasheet Resin Designs GT-1010 Sealing Strip

Information provided by Gluespec
  • Description for Resin Designs GT-1010 Sealing Strip

    Provide sealing and corrosion protection for indoor and outdoor equipment, including connectors and electrical components. Teflon-backed, one side tacky, forms tight environmental seal.

    *See Terms of Use Below

    Chemical Resistance Chemical Resistance: Solvent resistance
    Application Type Gasket
    1 Part or 2 Part 1-Part
    Material Form Strip
    Industry Connectors, Electrical components
    Manufacturer Resin Designs
    Chemistry Pre-cured silicone gel, Teflon®-backed
    Cure Method Pressure sensitive
    High Temperature Resistance (°C) 125, Forms an instant environmental barrier in hot temperatures
    Low Temperature Resistance (°C) -40, Forms an instant environmental barrier in cold temperatures
    Volume Resistivity (O) >1e11 (ohms/cm)
    Conformable Superior in conformability
    Key Specifications UL (Underwriters Laboratory), ULC (Underwriters Laboratories of Canada), NFPA (National Fire Protection Association): UL 94 HB
  • Technical Data for Resin Designs GT-1010 Sealing Strip

    Overview
    • Chemical Resistance
      • Chemical Resistance : Relative Solvent Resistance - Solvent resistance
    • Application Type
      • Gasketing - Gasket
    • 1 Part or 2 Part
      • 1-Part
    • Material Form
      • Strip
    • Industry
      • Electronics - Electrical components
      • Connectors
      • Industrial - Indoor equipment, Outdoor equipment, High-performance, Used as stamped pads where additional abrasion resistance to the non-sealing surface is required
    • Chemistry
      • Other - Teflon®-backed
      • Silicone - Pre-cured silicone gel
    • Cure Method
      • Pressure Sensitive (min) - Pressure sensitive
    • Key Specifications
      • UL (Underwriters Laboratory), ULC (Underwriters Laboratories of Canada), NFPA (National Fire Protection Association) : UL 94 HB
    Specifications
    Bond Strength
    General Bond Strength (psi) One side tacky
    Material Resistance
    Non-Corrosive Provide corrosion protection
    Abrasion Resistance Additional abrasion resistance
    Environmental Resistance Forms tight environmental seal
    High Temperature Resistance (°C) 125, Forms an instant environmental barrier in hot temperatures Test Method
    Low Temperature Resistance (°C) -40, Forms an instant environmental barrier in cold temperatures Test Method
    Conductivity
    Dielectric Strength (V/mil) 225
    Volume Resistivity (O) >1e11 (ohms/cm)
    Hardness
    Conformable Superior in conformability
    Elongation (%) >150
    Other Properties
    Specific Gravity 0.970 Test Method
    Business Information
    Shelf Life Details Because these are precured materials, there is no special storage condition required. Product should be stored in the original packaging under normal warehouse conditions to maintain the integrity of the packaging materials. Product shelf life and usage date is 48 months from the manufacturing date as the surface tack on some of the products can change after this time.
    Shelf Life Type From the manufacturing date
    Shelf Life (mon) 48
  • Best Practices for Resin Designs GT-1010 Sealing Strip

    *See Terms of Use Below

    1. Application

      Cold-applied, it is easily installed

      Installation: Application of Resin Designs sealing strips is fast and cost-effective. The product is installed easily and forms an instant environmental barrier in both hot and cold temperatures – no heating or other tools are required – and a rapid seal is created without the delay of lengthy cure cycles. Should inspection or repair be necessary, Resin Designs strips can be peeled away cleanly from the substrate.

  • Comparable Materials for Resin Designs GT-1010 Sealing Strip

    *See Terms of Use Below

    Spec Engine® Results

Popular Articles

Electrically Conductive Adhesives

Read Article

Testing the effectiveness of surface treatments

Read Article

6 objects held together by adhesives you probably can't live without

Read Article

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Read Article

Sponsored Articles

Unique Advantages of Contact Adhesives

Read Article

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Read Article

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Read Article

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Read Article

Featured Ads

Top Catalog Pages for Resin Designs GT-1010 Sealing Strip

Gluespec Poll

What level of expertise do you have in specialty chemicals like adhesives, sealants, conformal coatings, etc.?
High Temperature Resistance Test Methods
High Temperature Resistance Test Method
125°C Useful temperature
Forms an instant environmental barrier in hot temperatures
Low Temperature Resistance Test Methods
Low Temperature Resistance Test Method
-40°C Useful temperature
Forms an instant environmental barrier in cold temperatures
Specific Gravity Test Methods
Specific Gravity Test Method
0.970 Without backing