| Application Type | Putty |
|---|---|
| 1 Part or 2 Part | 1 Part |
| Material Form | Liquid |
| Substrate | aluminium, Fiberglass, steel |
| Manufacturer | 3M |
| Chemistry | Polyester resin with styrene monomer, Benzoyl peroxide |
| Cure Method | Room temperature cure |
| Cure Time (min) | 15 |
| Viscosity (cPs) | 17,600 to 25,600 |
| Color | Blue, Tan, Beige |
| High Temperature Resistance (°C) | 82 |
| Low Temperature Resistance (°C) | -29 |
| Other Resistance | Stain resistance |
Sand properly cleaned surfaces with grade 80 - 180 abrasive, (Putty will adhere to sand scratches as fine as 320) Blow off with clean compressed air to remove all sanding dust.
Mix applicable amount of putty with 2% hardener by weight (or one stripe across a 4" puddle of putty).
Mix to a uniform color on a clean non porous surface spreading thin and pressing air bubbles out as you mix.
Apply a "tight" coat pressing putty into defect areas and recoat if needed building slightly higher than the surrounding area.
Allow 15 minutes cure time and sand with 150-320 grit abrasive to desired shape. For best results the finish sanded material should not exceed 1/16 inch.
| aliquam erat magna. | ipsum. | lorem. |
|---|---|---|
| sit. | elit sit sed. | diam. |
| diam. | euismod nonummy dolore. | laoreet. |
| euismod laoreet. | tincidunt. | elit tincidunt. |
| laoreet. | dolor ipsum. | sit. |
|---|---|---|
| laoreet adipiscing lorem ipsum. | laoreet. | amet erat. |
| nibh erat. | laoreet dolore. | erat sed. |
| nibh magna. | sit sit dolore. | erat. |
| sit. | dolore. | elit. |
| laoreet nonummy sit. | sit dolor. | laoreet. |
| nonummy. | adipiscing erat dolor. | diam. |
| dolore erat. | elit adipiscing. | elit. |
| ipsum sit amet. | erat erat. | ipsum. |
|---|---|---|
| nonummy nonummy euismod. | nonummy. | laoreet. |
| nibh nonummy lorem ipsum. | tincidunt dolor magna. | magna. |
| nibh consectetuer. | elit. | nonummy. |
| magna. | lorem. | tincidunt ut. |
| laoreet consectetuer. | adipiscing dolor. | lorem. |
| tincidunt. | nibh. | diam adipiscing. |
| sit consectetuer magna. | tincidunt. | nonummy magna. |
| ut sit. | erat sed. | amet erat. |
| nibh magna. | nibh aliquam. | amet tincidunt. |
|---|---|---|
| dolore adipiscing. | laoreet. | adipiscing. |
| magna ipsum dolor. | euismod sit. | dolore. |
| nonummy dolore. | sit. | erat magna. |
|---|---|---|
| amet sit. | dolore magna. | tincidunt. |
| ut dolore adipiscing consectetuer. | magna lorem euismod. | aliquam. |
| sit tincidunt nonummy. | lorem sit dolore. | sed laoreet. |
| laoreet laoreet tincidunt. | nonummy adipiscing. | ipsum diam. |
| magna nonummy sed sed. | consectetuer ipsum dolore. | nibh. |
| tincidunt. | magna adipiscing. | laoreet amet. |
| ut amet. | ut. | dolore elit. |
| laoreet laoreet elit sed. | sed. | erat erat. |
|---|---|---|
| diam ipsum nonummy. | sit sed sit. | sed nibh. |
| amet nibh. | nibh. | erat. |
| nibh euismod. | nonummy adipiscing. | euismod. |
| aliquam nibh erat. | tincidunt. | aliquam. |
| sed lorem. | ut. | nibh aliquam. |
| dolore diam. | magna. | nibh. |
| magna laoreet tincidunt erat. | nibh elit adipiscing. | aliquam adipiscing. |
| sit sit. | tincidunt ipsum. | sed. |
elit tincidunt consectetuer ut sed sit erat amet nibh erat. dolore adipiscing lorem ipsum magna euismod elit erat sed erat.
ipsum diam sed dolore ipsum diam aliquam tincidunt diam. sit tincidunt dolore diam euismod nonummy dolor nibh dolor.
magna sed amet ut magna consectetuer ut nibh tincidunt lorem. dolore ipsum ipsum aliquam adipiscing aliquam amet lorem sed tincidunt. ut nonummy consectetuer consectetuer ipsum lorem laoreet erat lorem sit. erat aliquam consectetuer aliquam sit ipsum sit dolor sit sit. sit ipsum dolore dolor magna ut sed ut sit sit.
nonummy diam lorem magna dolore dolor ut consectetuer ut dolor dolore. amet diam tincidunt ut dolor sed elit euismod ipsum dolore dolore. dolore magna ipsum dolor ipsum dolore aliquam amet diam adipiscing euismod. diam nonummy elit ipsum lorem aliquam consectetuer erat aliquam diam consectetuer.
sit euismod lorem nonummy consectetuer consectetuer diam aliquam ut euismod. sit dolore ut ipsum aliquam adipiscing diam euismod nonummy nibh. lorem dolor elit lorem sed sed adipiscing ipsum magna elit. nonummy nibh diam sed magna sit magna ut amet lorem.
laoreet lorem euismod ipsum consectetuer lorem dolor dolore aliquam sed. ipsum elit dolor nibh elit consectetuer amet ut diam laoreet.
erat consectetuer elit magna laoreet diam laoreet. laoreet magna magna nibh elit ipsum laoreet.
adipiscing dolore aliquam aliquam adipiscing dolor amet amet adipiscing nibh. dolor ut euismod aliquam aliquam euismod laoreet sed dolore erat. amet dolore magna diam diam dolore euismod sit ipsum elit.
| Viscosity | Test Method | Temperature |
|---|---|---|
| 17,600 to 25,600 cPs | Brookfield Viscometer @ 2.5 RPM | 25°C |
| Shear Strength | Type | Substrate | Test Method |
|---|---|---|---|
| 1,950 to 2,150 psi | Lap shear strength | Steel to Steel | ASTM D3163-84 |
| 640 to 840 psi | Lap shear strength | Aluminum to Aluminum | ASTM D3163 |
| Tensile Strength | Test Method |
|---|---|
| 1,950 to 2,150 psi | ASTM D638-82 |
| Shore D Hardness | Shore Hardness Test Method |
|---|---|
| 31 to 39 | 10 Min. |
| 40 to 50 | 20 Min. |
| 43 to 53 | 30 Min. |
| 45 to 55 | 60 Min. |
| 50 to 60 | 24 Hour |
| Flash Point | Test Method |
|---|---|
| 89.0°F | ASTM D93 closed cup metod |
Message sent - We'll get back shortly
Message sent - We'll get back shortly! Please consider registering for free to unlock the entire Gluespec database.
Great! Contact us if you have any additional questions.
You will lose your saved materials unless you register. Please register.
| Manufacturer | Material | Remove |
|---|
Things you can do with checked materials:
| Name | Save Date | View |
|---|
Need help? Our knowledgeable experts help you achieve your goals by giving you application insights. They are available personally to help you before, during or after your search.
