3M 130C

3M 130C Datasheet
CONTACT REP

  • Description for 3M 130C

    A highly conformable, linerless, ethylene rubber (EPR), high-voltage insulating tape, formulated to provide excellent thermal dissipation of splice heat.

    *See Terms of Use Below

    Application Type Repair, Seal
    1 Part or 2 Part 1 Part
    Material Form Tape
    Industry Terminating wires and cables, Splicing wires and cables, Moisture-sealing electrical connections, Jacketing (secondary insulation) on high-voltage splices and terminations, Primary insulation for splicing all types of solid dielectric insulated cables through 69 kV, Primary insulation for building stress cones on all types of solid dielectric insulated cables up to 35 kV, Bus bar insulation, End-sealing high-voltage cables, Motor leads, Jacket repair
    Manufacturer 3M
    Chemistry ethylene rubber (EPR)
    Cure Method Pressure Sensitive
    Color Black
    Ozone Resistance Ozone Resistance
    High Temperature Resistance (°C) Heat Resistance

  • Technical Data for 3M 130C

    *See Terms of Use Below

    Overview
    • Application Type
    • 1 Part or 2 Part
      • 1 Part or 2 Part - 1 Part
    • Material Form
      • Tape
    • Industry
      • Electronics - Terminating wires and cables, Primary insulation for building stress cones on all types of solid dielectric insulated cables up to 35 kV, Jacketing (secondary insulation) on high-voltage splices and terminations, Bus bar insulation, End-sealing high-voltage cables, Motor leads, Jacket repair
      • Connectors - Moisture-sealing electrical connections
      • Splicing - Primary insulation for splicing all types of solid dielectric insulated cables through 69 kV, Splicing wires and cables
    • Chemistry
      • Other - ethylene rubber (EPR)
    • Cure Method
      • Pressure Sensitive (min) - Pressure Sensitive
    • Color
      • Black
    Specifications
    Bond Strength
    Tensile Strength (psi) 250 Test Method
    Material Resistance
    Ozone Resistance Ozone Resistance
    UV Resistance UV Resistance Test Method
    Environmental Resistance Weather resistant
    High Temperature Resistance (°C) Heat Resistance
    Conductivity
    Dissipation Factor 0.70%, 3.00% Test Method
    Dielectric Strength (V/mil) 750, 750, 730 Test Method
    Dielectric Constant 3.50, 3.60 Test Method
    Thermal Conductivity (W/m°K) High, 0.3 (W/m.C) Test Method
    Volume Resistivity (O) >10(15) (ohm-cm), >10(14) (ohm-cm) Test Method
    Hardness
    Elongation (%) 850 Test Method
    Other Properties
    Specific Volume (mm³) >10(15) (ohm-cm), >10(14)(ohm-cm) Test Method
    Business Information
    Shelf Life Details The 130C tape has a shelf life ( from date of manufacture) when stored under the following recommended storage conditions., Store behind present stock in a clean dry place at a temperature of 70°F (21°C) and 40% to 50% relative humidity. Good stock rotation is recommended.
    Shelf Life Temperature (°F) 70
    Shelf Life Type From date of manufacture.
    Shelf Life (mon) 61

  • Best Practices for 3M 130C

    *See Terms of Use Below

    1. Application

      This tape should be applied in successive half-lapped level wound layers until desired build-up is reached. It should be applied like any rubber tape

      that is, the side of the tape wrapped inside the roll should be applied outside on the splice (tacky side up). This will help prevent the roll from getting progressively further away from the work area.

      To eliminate voids in critical areas, highly elongate 130C tape. Stretch tape in critical areas just short of the breaking point

      doing so will not alter its physical or electrical properties. In less critical areas, less elongation may be used. The tape should be stretched to a minimum of 3/4 its original width. Always attempt to half-lap to produce a uniform buildup. When using 130C tape for splicing cable above 15 kV, always highly elongate the tape throughout the entire splice. Techniques for proper usage of 130C tape are contained in standard and special prints available though the “3M System for Splicing and Terminating” program. These are available through the local 3M Electrical Products Division representative.

  • Comparable Materials for 3M 130C

    *See Terms of Use Below

    Spec Engine® Results

    • 3M
      8979 SL(3M)

      A unique tape construction that allows for both permanent and temporary applications whether indoors or outdoors. It is removable with little or no adhesive residue from most opaque surfaces up to 6 months after application.

    • 3M
      480(3M)

      A transparent polyethylene backing with a long aging transparent acrylic adhesive. It can be used for splicing and repairing polyethylene sheeting. It is also recommended for sealing and protecting applications.

    • 3M
      3939(3M)

      Composed of waterproof polyethylene film over cloth scrim backing with a rubber adhesive used for demanding duct tape applications.

    • Compare All
  Download Technical Data Sheet   Save This Material Saved Items

Questions about this material?

3M - 130C

Get personal assistance with your specific application needs.

Your Profile Edit
Submit

Popular Articles

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Read Article

Testing the effectiveness of surface treatments

Read Article

Polysulfides in the Aerospace Industry

Read Article

Anaerobic Adhesives

Read Article

Sponsored Articles

Unique Advantages of Contact Adhesives

Read Article

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Read Article

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Read Article

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Read Article
Information provided by Gluespec

Why Register?

  • View Technical Details
  • View Test Methods
  • View Key Specifications
  • View Similar Materials
  • Save your Project Searches

Already registered? Sign in.

Questions? Learn more about Gluespec

Gluespec Poll

Which answer best describes a project you are currently working on?
Tensile Strength Test Methods
Tensile Strength Test Method
250 psi ASTM-D-4325
UV Resistance Test Methods
UV Resistance Test Method
UV Resistance ASTM-D-4388
Dielectric Constant Test Methods
Dielectric Constant Temperature Test Method
3.50 23°C ASTM-D-4325, 1200 volts @ 60 Hz
3.60 90°C ASTM-D-4325, 1200 volts @ 60 Hz
Dielectric Strength Test Methods
Dielectric Strength Test Method
750 V/mil ASTM-D-4325, Original
750 V/mil ASTM-D-4325 24 hrs. in H2O
730 V/mil ASTM-D-4325, 96 hrs. @ 23°C 96% RH
Dissipation Factor Test Methods
Dissipation Factor Temperature Test Method
0.70% 23°C ASTM-D-4325, (1200 volts @ 60 Hz)
3.00% 90°C ASTM-D-4325, (1200 volts @ 60 Hz)
Thermal Conductivity Test Methods
Thermal Conductivity Temperature Test Method
High
0.3 (W/m.C) 23°C ASTM-C-518
Volume Resistivity Test Methods
Volume Resistivity Temp (°C) Test Method
>10(15) (ohm-cm) ASTM-D-4325, Original
>10(14) (ohm-cm) 23°C ASTM-D-4325, Aged 96 hrs. @ 23°C 96% RH
Elongation Test Methods
Elongation Test Method
850 % ASTM-D-4325
Specific Volume Test Methods
Specific Volume Test Method
>10(15) (ohm-cm) ASTM-D-4325 Original
>10(14)(ohm-cm) ASTM-D-4325 Aged 96 hrs. @ 23°C 96% RH
;