• Description for 3M 4150S

    Acrylic solution in Xylene, Clear Liquid, Aircraft Films to help prevent the aircraft film from, Excellent water resistance.

    *See Terms of Use Below

    Chemical Resistance LD-4, Chemical Resistance: Mild Acids, Chemical Resistance: Fluid Resistance: Excellent water resistance, Mild Alkalis, Salts, Hydraulic Fluid
    Application Type Seal
    1 Part or 2 Part 1-Part
    Material Form Liquid
    Manufacturer 3M
    Chemistry Acrylic solution in Xylene
    Cure Method Air dry
    Application Temperature (°F) 50 to 100
    Viscosity (cPs) >700
    Color Clear
    High Temperature Resistance (°C) 65
    Low Temperature Resistance (°C) -51
  • Technical Data for 3M 4150S

    Overview
    • Chemical Resistance
      • Chemical Resistance : Fluid Resistance : Water Resistance - Excellent water resistance
      • Chemical Resistance - Mild Alkalis, Salts, Hydraulic Fluid, LD-4
      • Chemical Resistance : Acid Resistance - Mild Acids
    • Application Type
    • 1 Part or 2 Part
      • 1-Part
    • Material Form
      • Liquid
    • Industry
      • Other - around all exposed edges of film
    • Chemistry
      • Acrylic - Acrylic solution in Xylene
    • Application Method
      • Brush
      • Other - dauber
    • Cure Method
      • Room Temperature / Air Dry - Air dry
    • Color
      • Clear / Transparent - Clear
    Specifications
    Cure Specs
    Application Temperature (°F) 50 to 100
    Viscosity (cPs) >700
    Material Resistance
    High Temperature Resistance (°C) 65 Test Method
    Low Temperature Resistance (°C) -51 Test Method
    Other Properties
    % Solids (%) 36 to 41
    Business Information
    Shelf Life Details Use within two years from the date of manufacture on the original can.;Use within one year after opening the can.;Storage conditions! +4°C to +40°C, out of sunlight, original container in clean and dry area.;The shelf life as defined above remains an indicative and maximum data, subject to many external and non-controllable factors. It may never be interpreted as warranty., Use within two years from the date of manufacture on the original can.;Use within one year after opening the can.;Storage conditions! +4°C to +40°C, out of sunlight, original container in clean and dry area.;The shelf life as defined above remains an indicative and maximum data, subject to many external and non-controllable factors. It may never be interpreted as warranty.
    Shelf Life Temperature (°F) 39 to 104, 39 to 104
    Shelf Life Type From the date of manufacture, Shelf Life Type
    Shelf Life (mon) 24, 12
  • Best Practices for 3M 4150S

    *See Terms of Use Below

    1. Application

      Do not apply edge sealer unless the temperature is above the minimum recommended temperature.

      Remove any application tape and re-squeegee the edges before applying the edge sealer.

      Make sure all edges to be sealed are clean, dry and free of contaminants.

      To preserve the unused portion of the edge sealer, transfer the desired amount into a separate disposable container and tightly recap the original container immediately. Leaving the original container open allows air to contaminate, reducing future shelf life.

      Applying a Liquid Edge Sealer: 1. Do not thin the sealer.

      2. Use the dauber supplied with edge sealer or a 1/4 inch (0.6 cm) brush.

      3. Wipe any excess edge sealer off the dauber or brush.

      4. Hold the brush or the flat edge of the dauber so that it straddles the film and substrate.

      5. Pull the dauber or brush along the edge in a smooth, continuous motion. Make sure the entire edge is covered with no gaps.

      6. Use opened and/or mixed sealer within two hours and discard any used sealer.

      7. Air dry for 24 hours before putting the graphic into service.

    2. Clean-Up

      Wipe any excess edge sealer off the dauber or brush

    3. Removal

      Removal of Edge Sealer Edge Sealer can be removed using isopropyl alcohol or 3M™ Scotch-Weld™ Citrus Cleaner.

  • Comparable Materials for 3M 4150S

    *See Terms of Use Below

    Spec Engine® Results

    Closest Results from this Manufacturer

Popular Articles

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Read Article

Testing the effectiveness of surface treatments

Read Article

Silicones in LED Lighting | Gluespec

Read Article

What Are the Differences Between Adhesives and Sealants?

Read Article

Sponsored Articles

Unique Advantages of Contact Adhesives

Read Article

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Read Article

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Read Article

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Read Article

Featured Ads

Top Catalog Pages for 3M 4150S

Gluespec Poll

What level of expertise do you have in specialty chemicals like adhesives, sealants, conformal coatings, etc.?
High Temperature Resistance Test Methods
High Temperature Resistance Test Method
65°C After Application
Low Temperature Resistance Test Methods
Low Temperature Resistance Test Method
-51°C After Application