Henkel Lite-Lok 465 Datasheet Henkel Lite-Lok 465

Information provided by Gluespec
  • Description for Henkel Lite-Lok 465

    • Light Curable Sealant • Fast cure under UV light • 100 % solids, no solvents or by-products upon curing • Good thermal cycling resistance • Versatile adhesion • Hard, tack free cured surface • High strength and durable •<br/>

    *See Terms of Use Below

    Brand Bondmaster
    Application Type Seal
    1 Part or 2 Part 1-Part
    Material Form Liquid
    Substrate Metal, Polyolefins
    Industry Motor
    Manufacturer Henkel
    Chemistry Urethane Acrylate, Urethane Acrylate, Urethane Acrylate
    Cure Method UV
    Cure Time (min) Fast, 0.02 to 0.05
    Viscosity (cPs) 10,000
    Color Transparent
    Other Resistance Good thermal cycling resistance
  • Technical Data for Henkel Lite-Lok 465

    • Application Type
    • 1 Part or 2 Part
      • 1-Part
    • Material Form
      • Liquid
    • Substrate
      • Polyolefin - Polyolefins
      • Metal
    • Industry
      • Motors - Motor
    • Chemistry
      • Acrylated Urethane - Urethane Acrylate
      • Acrylic - Urethane Acrylate
      • Polyurethane - Urethane Acrylate
    • Application Method
      • Dispenser - Piston pump dispensing system, Pressure pot
    • Cure Method
      • UV / Visible Light - UV
    • Color
      • Clear / Transparent - Transparent
    • Brand
      • Bondmaster
    Cure Specs
    Cure Time (min) Fast, 0.02 to 0.05
    Viscosity (cPs) 10,000 Test Method
    Bond Strength
    General Bond Strength (psi) High
    Impact Strength (psi) Impact strength
    Material Resistance
    Impact Resistance Good impact resistance
    Moisture/Humidity Resistance Good
    Other Resistance Good thermal cycling resistance
    Other Properties
    Specific Gravity 1.070
    Flash Point (°F) >212.0
    % Solids (%) 100
    Business Information
    Shelf Life Details LITE LOK 465 has a shelf life of six months when stored at or below 27°C (80°F). Do not freeze.
    Shelf Life Temperature (°F) <81
    Shelf Life (mon) 6
  • Best Practices for Henkel Lite-Lok 465

    *See Terms of Use Below

    1. Surface Preparation

      LITE-LOK 465 bonds well to many untreated surfaces. However, adhesion is often improved by surface preparation before bonding. The surface should be free of contamination such as dirt, dust, grease or oil. An alcohol wipe is suitable for cleaning most surfaces. Optimum strength is obtained by abrading the surface followed by a solvent wipe to remove any loose particles. Polyolefins must be corona treated, or flame treated before bonding.

    2. Application

      LITE-LOK 465 is best applied by extruding the product onto the substrate to be sealed or bonded using a 14-16 gauge dispensing tip. Sufficient product must be applied to seal all gaps, and completely coat the part to be bonded or sealed. After dispensing onto the part, the product should be cured as soon as possible to prevent any pre-reaction with ambient light.

      LITE-LOK 465 may be applied via a pressure pot, or piston pump dispensing system. All fittings and tubing used in the dispensing system must be opaque to light.

    3. Curing

      Optimum cure is obtained when LITE-LOK 465 is exposed to UV light. The peak reactivity of the product is from exposure to light from 325 nm through 365 nm. The time needed for curing is a combination of many factors. Some of these are as follows: The thicker the substrate, the longer the exposure time needed for curing. The more UV light absorbing that the substrate is, the longer the exposure time needed for curing. The lower that the intensity of the UV light source is, the longer the exposure time needed for curing. The farther the distance of the product from the UV light source, the longer the exposure time needed for curing.

      Typically, LITE-LOK 465 will cure after a UV light exposure from one to three seconds, when cured at or near the focal point of a high intensity UV light source. To achieve complete cure, all of the product must be exposed to the UV light source.

  • Comparable Materials for Henkel Lite-Lok 465

    *See Terms of Use Below

    Spec Engine® Results

    Closest Results from this Manufacturer

Popular Articles

Testing the effectiveness of surface treatments

Read Article

What Are the Differences Between Adhesives and Sealants?

Read Article

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Read Article

An Overview of Fluid Dispensing Systems & How They’re Used

Read Article

Sponsored Articles

Unique Advantages of Contact Adhesives

Read Article

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Read Article

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Read Article

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Read Article

Featured Ads

Top Catalog Pages for Henkel Lite-Lok 465

Gluespec Poll

Which answer best describes a project you are currently working on?
Viscosity Test Methods
Viscosity Test Method Temperature
10,000 cPs Approximate 25°C