Parker Lord 406 Acrylic Adhesive w/ Accelerator 19GB Datasheet Parker Lord 406 Acrylic Adhesive w/ Accelerator 19GB

Information provided by Gluespec
  • Description for Parker Lord 406 Acrylic Adhesive w/ Accelerator 19GB

    A two part component is specifically formulated to provide the highest impact and peel strengths available in a room temperature curing adhesive and it is used for bonds a wide range of unprepared metals

    *See Terms of Use Below

    Chemical Resistance Resists alkalis, Chemical Resistance: Resists solvents, Chemical Resistance: Resists dilute acids, Resists greases, Resists oils, Resists salt spray
    Application Type Bond
    1 Part or 2 Part 2-Part
    Material Form Paste
    Substrate Acrylic, A wide variety of prepared metals, Engineered plastics, Polycarbonate, ABS, A wide variety of unprepared metals, Engineered thermoplastics
    Industry Heavy-Duty Truck, Trailer
    Manufacturer Parker Lord
    Chemistry Acrylic, Flammable, Versatile
    Cure Method 2-Part Cure, Heat Cure, Room temperature cure
    Cure Temperature (°C) 24 Room temperature
    Cure Time (min) 1,440
    Viscosity (cPs) Non-Sag, 100,000 to 300,000
    Color Tan
    High Temperature Resistance (°C) 149
    Low Temperature Resistance (°C) -40
    Density (g/cm³) 9.10-9.70 (lb/gal)
  • Technical Data for Parker Lord 406 Acrylic Adhesive w/ Accelerator 19GB

    Overview
    • Chemical Resistance
      • Chemical Resistance - Resists alkalis, Resists greases, Resists oils, Resists salt spray
      • Chemical Resistance : Relative Solvent Resistance - Resists solvents
      • Chemical Resistance : Acid Resistance - Resists dilute acids
    • Application Type
    • 1 Part or 2 Part
      • 2-Part
    • Material Form
      • Paste
    • Substrate
      • Metal - A wide variety of prepared metals, A wide variety of unprepared metals
      • Plastic - Engineered plastics, Engineered thermoplastics
      • Acrylic (PMMA) - Acrylic
      • Polycarbonate
      • ABS
      • Other - XENOY®, Vertical surfaces, Overhead surfaces
    • Industry
      • Heavy-Duty Truck
      • Trailer
    • Chemistry
      • Acrylic
      • Other - Flammable, Versatile
    • Application Method
      • Dispenser - Automatic meter/mix/dispense equipment
      • Other - Handheld Cartridges
    • Cure Method
      • Room Temperature / Air Dry - Room temperature cure
      • Heat - Heat Cure
      • 2-Part Cure
    • Color
      • Brown - Tan
    Specifications
    Cure Specs
    Cure Temperature (°C) 24 Room temperature Test Method
    Cure Time (min) 1,440 Test Method
    Viscosity (cPs) Non-Sag, 100,000 to 300,000 Test Method
    Fixture or Handling Strength Time (min) 12 to 17 Test Method
    Work / Pot Time (min) 6 to 10 Test Method
    Mix Ratio 4:1 (by volume), 2.91:1 (by weight)
    Bond Strength
    Peel Strength (piw) Highest
    Impact Strength (psi) Highest
    Material Resistance
    UV Resistance Excellent resistance to indirect UV exposure
    Environmental Resistance Resists weathering
    High Temperature Resistance (°C) 149 Test Method
    Low Temperature Resistance (°C) -40
    Moisture/Humidity Resistance Resists moisture
    Other Properties
    Flash Point (°F) 59.0 Test Method
    % Solids (%) 100 Test Method
    Density (g/cm³) 9.10-9.70 (lb/gal) Test Method
    Business Information
    Shelf Life Details Shelf life is nine months when stored below 80°F (27°C) in original, unopened container. Storage temperatures of 40-50°F (4-10°C) are recommended. If stored cold, allow product to return to room temperature before using. Protect from exposure to direct sunlight.
    Shelf Life Temperature (°F) <80
    Shelf Life (mon) 9
    Not Good For
    Don't Use For Household applications
  • Best Practices for Parker Lord 406 Acrylic Adhesive w/ Accelerator 19GB

    *See Terms of Use Below

    1. Surface Preparation

      Remove grease, loose contamination or poorly adhering oxides from metal surfaces. Normal amounts of mill oils and drawing compounds usually do not present a problem in adhesion. Most plastics require a simple cleaning before bonding. Some may require abrading for optimum performance.

    2. Application

      Apply adhesive using handheld cartridges or automatic meter/mix/dispense equipment

      Handheld Cartridges: Load the cartridge into the applicator gun and remove the end caps.

      Level the plungers by expelling a small amount of adhesive to ensure both sides are level.

      Attach mixing tip and expel a mixer’s length of adhesive.

      Apply adhesive to substrate and mate the parts within the working time of the adhesive. Clamp in position until adhesive reaches handling strength.

      Meter/Mix/Dispense Equipment Contact your LORD representative if assistance is needed using this equipment.

    3. Mixing

      Mix LORD 406 acrylic adhesive with the proper amount of LORD Accelerator 19GB. Handheld cartridges will automatically dispense the correct volumetric ratio of each component. Even color distribution visually indicates a thorough mix. Once mixed, the adhesive cures rapidly.

    4. Curing

      Cure begins immediately once adhesive and accelerator are mixed. Time to handling strength is dependent on adhesive used. Complete cure requires 24 hours at room temperature. Mating surfaces must be held in contact during the entire curing process. Cure rate can be accelerated by applying modest heat [<150°F (<66°C)]. Cured adhesive is colored to visually indicate a full cure

      cure color depends on the accelerator used.

      Cure rate can be accelerated by applying modest heat [<150°F (<66°C)].

    5. Clean-Up

      Clean equipment and tools prior to the adhesive cure with solvents such as isopropyl alcohol, acetone or methyl ethyl ketone (MEK). Once adhesive is cured, heat the adhesive to 400°F (204°C) or above to soften the adhesive. This allows the parts to be separated and the adhesive to be more easily removed.

  • Comparable Materials for Parker Lord 406 Acrylic Adhesive w/ Accelerator 19GB

    *See Terms of Use Below

    Spec Engine® Results

Popular Articles

Testing the effectiveness of surface treatments

Read Article

Infographic: ENSURING A STRONG BOND - 6 Basic Methods of Surface Preparation

Read Article

Plastic Bonding with Adhesives - Considerations Q&A

Read Article

What Projects Require Custom Adhesive Formulations and Why?

Read Article

Sponsored Articles

Unique Advantages of Contact Adhesives

Read Article

Using LOCTITE® 454™ is a Valid Option for Engineers Working with a Wide Variety of Materials

Read Article

Sylgard 184 by DOW is the Top Choice for a Transparent, Silicone Encapsulant. Read Why:

Read Article

Case Study: Creating reliable, corrosion-free bonds with LORD® 406 acrylic adhesive

Read Article

Featured Ads

Top Catalog Pages for Parker Lord 406 Acrylic Adhesive w/ Accelerator 19GB

Gluespec Poll

What level of expertise do you have in specialty chemicals like adhesives, sealants, conformal coatings, etc.?
Cure Temperature Test Methods
Cure Temperature Cure Time Test Method
24°C Room temperature Full Cure Time, Mixed, Data is typical and not to be used for specification purposes.
Cure Time Test Methods
Cure Time Test Method
1,440 min Full Cure Time, Mixed, Data is typical and not to be used for specification purposes.
Fixture or Handling Strength Time Test Methods
Fixture or Handling Strength Time Fixture-Handling Strength Test Method Fixture-Handling Strength Time Temperature
12 to 17 min Time to Handling Strength, Mixed, 60 psi Shear, Data is typical and not to be used for specification purposes. 24°C
Viscosity Test Methods
Viscosity Test Method Temperature
Non-Sag
100,000 to 300,000 cPs Brookfield, Data is typical and not to be used for specification purposes. 25°C
Work / Pot Time Test Methods
Work / Pot Time Test Method Temperature
6 to 10 min Working Time, Mixed, Data is typical and not to be used for specification purposes. 24°C
High Temperature Resistance Test Methods
High Temperature Resistance Test Method
149°C Based on test results, LORD 406/19GB adhesive system exhibits post bake/powder coating temperature resistance up to 400°F (204°C) for 90 minutes. Customer specific substrates should always be evaluated for specific application performance
Density Test Methods
Density Test Method
9.10-9.70 (lb/gal) Data is typical and not to be used for specification purposes.
Flash Point Test Methods
Flash Point Test Method
15.0°C Data is typical and not to be used for specification purposes
% Solids Test Methods
% Solids Test Method
100 % Data is typical and not to be used for specification purposes